I N F O INSTALLATION AND INSTRUCTION MANUAL BUILT-IN REFRIGERATOR 2222 680-53 ER 6424 U-ER 1424 U
WARNINGS GB It is most important that this instruction book should be retained with the appliance for future reference. Should the appliance be sold or transferred to another owner, or should you move house and leave the appliance, always ensure that the book is supplied with the appliance in order that the new owner can be acquainted with the functioning of the appliance and the relevant warnings. These warnings are provided in the interest of safety.
CONTENTS GB Installation 3 ª Positioning the door shelves 8 ª Positioning 3 ª Freezing fresh food 9 ª Cleaning the interior 3 ª Storage of frozen food 9 ª Door reversibility 4 ª Thawing 9 ª Building the appliance in under a worktop 4 ª Ice-cube production 10 ª Inner door reversal 6 ª Defrosting 10 ª Electrical connection 6 Maintenance 11 Technical specification 6 ª Periodic cleaning 11 ª Periods of non-operation 11 Use 7 ª Temperature regulation ª Interior light 11 7
Door reversibility Before carrying out any work, remove the plug from the power socket. Slide the ventilation grille into the guide rails and remove the left-hand side (1) (Fig. 1). Changing the door opening direction to the left Unscrew pins (A) at top and bottom and remove the corresponding spacers. Remove the door. Unscrew screws (C) and move the right-hand hinges (top and bottom) towards the inside and the left-hand hinges (top and bottom) towards the outside. Re-insert the screws into holes (D) (Fig.
Refer to Fig. 5 for required dimensions of the recess. Fig. 5 600 820÷870 600 550 D100 The appliance is equipped with adjustable support feet (Fig. 6). To adapt the appliance to the height of the installation area, remove the feet, screw on nuts (A) (which you will find in the pack) then refit the feet. Finally, adjust the height and fully tighten the nuts. Fig. 6 A D101 Fig. 7 Slide the appliance into the recess, pushing it against the adjacent cabinet wall on the handle side.
Open both the appliance door and that of the kitchen unit to approx. 90°. Place the little plates over the runners. Hold the doors of the appliance and the unit together and mark the holes. Remove the little plates and make the holes with a diam. of 2 mm. Replace the little plates over the runners and screw in the screws provided (3.5x16 mm). For the alignment of the kitchen unit door, if necessary, use the clearance size of the slotted holes.
USE GB Operation Fresh food refrigeration Insert the plug into the wall socket. Open the refrigerator door and turn the thermostat knob, clockwise, beyond the «O» (STOP) position. The appliance will start to operate. To obtain the best performance: Temperature regulation Position food so that air can circulate freely round it.
Movable shelves Fig. 13 The walls of the refrigerator are equipped with a series of runners so that the shelves can be positioned as desired. Positioning the door shelves D040 Fig. 14 To permit storage of food packages of various sizes, the door shelves can be adjusted in height. To make these adjustments proceed as follows: Gradually pull the shelf in the direction of the arrows until it comes free, then reposition as required.
Freezing fresh food Storage of frozen food The 4-star compartment ( ) is suitable for long term storage of commercially frozen food and for freezing fresh food. The compartment marked is suitable for long-term storage of frozen and deep-frozen food. To freeze fresh foods it is not necessary to change the setting of the thermostat knob.
Ice-cube production This appliance is equipped with one or more trays for the production of ice-cubes. Fill these trays with water, then put them in the freezer compartment. Do not use metallic instruments to remove the trays from the freezer. Defrosting Frost is automatically eliminated from the evaporator of the refrigerator compartment every time the motor compressor stops, during normal use.
MAINTENANCE Unplug the appliance before carrying out any maintenance operation. GB Interior light The light bulb inside the refrigerator compartment can be reached as follows: Periodic cleaning Fig. 18 Never use metal objects for cleaning your appliance as it may get damaged. Clean the inside with warm water and bicarbonate of soda. Rinse and dry thoroughly. Clean the condenser and compressor with a brush or vacuum cleaner. This will improve efficiency of operation and so save energy. Fig.