Specification

Sealed Lead-Acid Charger
24BC5000T-4
UPG No. 71698
All specifications are subject to change without notice.
488 S. Royal Lane Coppell, Texas 75019 P 469.892.1122 T 866.892.1122 F 469.892.1123 [e-mail]
www.upgi.com
Dimensions: inches (mm)
Input Voltage 100 - 240Vac +/-10%
Input Frequency
50 - 60Hz
Over Voltage Protection
DC 31V Max.
Over Current Protection
DC 6A Max.
Leakage Current
0.75mA Max.
Input Power
180W
Output Voltage
Fast Charge (AGM)
DC 29.6V (+/- 0.2V)
DC 28.6V (+/- 0.2V)
Float Charge (AGM)
Fast Charge (GEL)
Float Charge (GEL)
DC 27.4V (+/- 0.2V)
DC 26.6V (+/- 0.2V)
Charging Current
Fast Charge
DC 5000mA +/- 5%
Float Charge
<DC 1000mA
Maintenance Stage
Auto-Restart @ 25.3VDC
Specification
Input Standby Power <0.5W
>85% @ Full Load
Battery Charging Capacity
15 - 50 Amp Hours
Output Cord
Dielectric Withstand Voltage
Insulation Resistance
Operation Temperature
Storage Temperature
Features:
Protections:
1.8m long, SJT type (Hard Usage) with XLR
3-pin Male Connector
AC 3.0KV for 1 min. @ 10mA leakage
A HighCurrent Fast Charge State: battery charges at 5000mA fast charge
current rate until battery voltage of 29.6V is reached.
1.
A Topping Charge State: battery charges at 29.6V constant voltage and
current begins to taper until current is less than 1000mA.
2.
A Precision Float Charge State
holds the battery voltage at 27.4V.
3.
For AGM batteries the charger provides Three Charge States. An integrated
circuit monitors and controls both the output voltage and current of the
charger through three separate charge states.
A HighCurrent Fast Charge State: battery charges at 5000mA fast charge
current rate until battery voltage of 28.6V is reached.
1.
A Topping Charge State: battery charges at 28.6V constant voltage and
current begins to taper until current is less than 1000mA.
2.
A Precision Float Charge State
holds the battery voltage at 26.6V.
Short Circuit Protection
Over Current Protection
Over Voltage Protection
Battery Polarity Reversal
3.
For GEL batteries the charger provides Three Charge States. An integrated
circuit monitors and controls both the output voltage and current of the
charger through three separate charge states.
50Mohm Min. at 500Vdc between Primary
and Secondary
8.00 (203)
3.30 (83.8)
2.04 (51.8)
Power On
No Battery/Full Charge (20 Hrs)
On Steady
On
Continuous Blinking
Bulk /Absorption Charge
Float Charge
Maintenance Charge
No AC Power
On
1. Power LED (Clear Lens - Red Color)
2. Charging / Faults - LED (Clear Lens - Red / Green Color)
Description
LED
Charging - Description
Red LED
Green LED
2 LEDs for Status Indication
Over current from charger
No batteries - Voltage < 9V
12 hr. charge timed out
Battery voltage < 14V
Batteries are connected
in reverse polarity
INDICATION
CHARGE/FAULT - Red LED
FAULT
1
2
3
4
5
6
Safety Standards
The charger shall meet the requirements of
UL 1012 special purpose, ISO 7176 -14, ISO
to DOE and CEC requirements per 10 CFR 430,
subpart B, appendix Y.
Due to contiuous improvements to our products, product may vary slightly from depiction.
The factory default for this charger is set to charge AGM batteries. To charge GEL
batteries move the switch located on the front end of the charger to the GEL
position.
-13 F/-25 C to +122 F/50 C
-13 F/-25 C to +140 F/60 C
Note:
continuous operation. For battery maintenance this battery is equiped with
“Auto-Restart” that will start the charge cycle again when battery voltage drops
to 25.3VDC.
G1906-1
Copyright 2019 Universal Power Group, Inc. All rights reserved.
UPG is ISO 9001 Certified.