Owner’s Manual Patio Heater Contact us for assistance: service@u-pha.
SAFETY INFORMATION Before you assemble or operate this unit, please carefully read this entire manual. Failure to do so WARNING • The installation of this unit must adhere to local codes or Propane Storage and Handling Code, CSA B149.2. • THIS UNIT IS INTENDED FOR OUTDOOR USE ONLY! This product shall be used outdoors, in a ventilated space and shall not be used in any enclosed area. • This unit is to be used with propane gas only! (sold separately) • Do not attach a remote gas supply to this unit.
damaged parts should this occur. • Do not disconnect any part while unit is in use. • Do not store a spare propane tank on or near this unit. • If the heating unit is indoors, detach the propane tank and leave outdoors. • • Always remove protective cover before operating (if applicable). • Check for leaks after not using the unit for long periods of time. • Children should never operate this unit. Children must be supervised while near this unit. • Keep gas tank at least 5 feet away from unit when lit.
SAFETY INFORMATION 48" 48" BE CAREFUL: WHEN CERTAIN MATERIALS OR ITEMS ARE STORED ABOVE, BESIDE OR UNDER THIS HEATER WHILE IN USE, THEY WILL BE SUBJECT TO RADIANT HEAT AND COULD BE SERIOUSLY DAMAGED. Combustible materials should not be within 48 inches of the top of the unit, or within 48 inches around the entire unit. Contact us for assistance: service@u-pha.
HARDWARE AA BB CC GG HH II MM NN DD JJ OO EE KK FF LL PP Item Description Qty AA Bolt M6x10 BB CC DD EE M6 nut Screw M5x10 Stud Wing nut 4 4 18 3 3 6 4 30 1 1 1 1 1 1 4 4 FF Flat washer GG Fixing Bracket HH Screw 3/16” II JJ KK LL MM NN Knob Large flat washer OO PP Screw M4 X 8 Philips screwdriver Wrench AA Battery (1.5 V) Anchoring arm Screw M6X12 Before beginning assembly of product, make sure all parts are present.
CONTENTS A B C D E F J K G L H M I N Item Description Qty A Reflector 1 B Top Plate Assy 1 C Glass Tube 1 D Upper Support 4 E Protective Guard 4 F Black Silicone Ring 1 G Side Panel 3 H Front Panel 1 I Gas Hose & Regulator 1 J Block belt 1 K Control Box Assy 1 L Lower Support 4 M Wheel Assembly 1 N Bottom Plate 1 Page 6 Contact us for assistance: service@u-pha.
ASSEMBLY INSTRUCTIONS 1.Assemble the wheel assembly (M) to the bottom plate (N) using 4pcs bolt M6x10 (AA) and 4pcs M6 nut (BB). 1 Hardware Used AA Bolt M6x10 x4 BB M6 nut x4 AA M BB 2-1. Unscrew the ignition, load battery, tighten the ignition. 2-2. Attach 4pcs anchoring arm (OO) to 4pcs lower support (L) using 4pcs screw M6X12 (PP). 2-1 2-2 2-3. Insert the pins of the bottom plate (N) to the holes of lower support (L), press to secure the pins.
3.Assemble block belt. Fix the block belt (J) to the 2pcs of lower support (L) using 2pcs screw M5x10. ATTENTION: Ensure the block belt and wheel assembly are on the same side. CC Screw M5x10 x2 J CC 4 WARNING Remove protective cover before assembling. 4. Assemble the reflector (A) onto the top plate assy (B).
5-1. Assemble top plate assy (B) to upper support (D) using 8pcs screw 3/16” (HH) . (L) using 8pcs screw M5x10 (CC) . 5-2. Insert upper support (D) to lower support Hardware Used CC HH HH 5 D Screw M5x10 x8 Screw 3/16” x8 CC 6.Carefully install the glass tube (C) by lifting up and inserting through the centre hole in the top plate assy (B). Ensure the black silicone ring (F) is attached to the lower edge of the glass tube (C) as illustrated.
7.Assembly the protective guard (E). Hang the hooks of the protective guard (E) onto the holes in upper supports Secure the protective guards (E) with fixing brackets (GG) with 4pcs Screw 3/16” (HH). 7 GG Hardware Used E HH Screw 3/16” x4 GG Fixing Bracket x4 8. Assemble three side panels (G) to lower support (L) using 18pcs screw 3/16”. 8 Attention: Do not cover the front side where the control knob is. HH Hardware Used HH Screw 3/16” x 18 Page 10 Contact us for assistance: service@u-pha.
9.Attach the knob (II) to front panel (H) using screw M4x8 (KK) and large flat washer (JJ). 9 Note: Put screw (KK) through large flat washer (JJ) then through the end link of the retainer chain. Insert screw into hole on front door panel and attach the knob (II) Hardware Used II Knob x1 KK KK Screw M4 X 8 x1 JJ Large flat washer x1 II JJ H 10.Place the propane gas tank (not included) on the base. Tighten the belt to ensure the propane gas tank is fully secure. 11.
OPERATION Before performing a leak test, be sure that no sparks can occur and you are in a spacious outdoor area. Connect the propane gas tank to the regulator and turn the valve on the unit to the “off” position. Brush a soap and water mixture on all connections. Turn the gas supply on; if bubbles occur on any connection there may be a leak. If you smell gas or a leak is discovered turn the gas valve off, disconnect propane gas tank and do not use the appliance until the leak is repaired.
MAINTENANCE • Before performing any maintenance always disconnect propane gas tank. • Keep the heating item free and clear from combustible materials. • Visually inspect burner for obstructions and keep tank enclosure free and clear from debris. • Use a soft brush to get rid of the mild stains, loose dirt and soil after the burner is completely cooled down. Wipe down with a soft cloth. • Harsh weather conditions may cause stubborn stains, discoloration and possibly rust pitting.
TROUBLESHOOTING Problem Cause Solution The burner will not light. The burner injector is clogged. Clean the burner injector. There is low gas supply pressure. Call your gas supplier. The burner flame goes off immediately after ignition. There is low gas pressure. Call your gas supplier. The ignition is delayed. The main burner carryover ports are clogged. Clean the main burner ports. There is low gas pressure. Call your gas supplier. The combustion on the burner is There is not enough air.