Operation Manual

ETW193
electronic programmable timer
OWNER’S
MANUAL
Congratulations on your
purchase of a UPM timer.
Please take the time to
read and understand this
manual so you can begin
to enjoy the security and
energy saving benefits this
product has to offer.
FEATURES
!
!
!
!
!
!
20 ON programs /
20 OFF programs
3 random functions
12/24 hour clock
500W loading
single pole or three-way
Countdown timer -
“One-Touch Countdown”
SINGLE POLE INSTALLATION
1
2
Remove existing switch and identify the wires in the wall box.
Using the supplied wire nuts, securely fasten the wires on the timer
to the wires in the wall box according to diagram FIGURE 1.
3
Disconnect the power supply at the circuit breaker or fuse before
proceeding with the installation.
Connect one of the (hot) wire on the timer to the
wire in the wall box.
black hot
Connect the other (hot) wire on the timer to the wire
in the wall box coming from the light fixture.
black hot
GETTING STARTED
setting the clock
1
4
2
1
5
6
7
8
Press SET
Day select with
Press SET
Hour select with
Press SET
Minute select with
3
5
7 9
2
4
6
8
10
9
10
3
Press SET
Second select with
Press SET
Press SET
Minute select with
memory backup
This UPM wall switch timer comes with built-in memory backup protection. In the
event of a power outage, all program and clock settings will remain in memory.
CLOCK
ON
MO
CLOCK
ON
MO
To activate/deactivate Daylight Saving Time (DST) function, press and hold
both and together for 3 seconds in mode; solid for DST
CLOCK
To toggle between 12/24 hour format, press RND during clock setting
CAUTION!
*
This timer is only compatible with incandescent (120V) lighting
applications. The timer must be used with magnetic
transformers, motors or loads exceeding 500W.
NOT
All wiring must comply with applicable codes and regulations.
TO AVOID FIRE, SHOCK, OR DEATH; SHUT OFF POWER SUPPLY AT
THE CIRCUIT BREAKER OR FUSE AND TEST THAT THE POWER IS
OFF BEFORE WIRING.
Handle installation with caution to prevent any risk of electrical shock
that could cause serious injury or death. If you are not sure about any
part of the given instructions, consult a qualified electrician.
For proper grounding, connect the (ground) wire on
the timer to the ground “screw” found inside the wall box.
green
Mount timer into the wall box carefully.
Restore power supply at the circuit breaker or fuse.
4
5
Terminate the (three-way) wire on the timer with a wire nut.
(For a single pole installation, the red wire is not needed).
red
INSTALLING THE TIMER IN PLACE OF LOAD SWITCH
FIGURE 3
THREE-WAY INSTALLATION DIAGRAM
JUMPER WIRE
COMMON TERMINAL
HOT WIRE
HOT WIRE
CLOSE UP VIEW OF THE HOT SWITCH
Go to using
CLOCK
GETTING STARTED
button placements
display
1
2
CD - activates countdown timer
3
4
SET - activates set functions
RND - activates random functions
5
- scrolls through selections
6
ON/OFF - manual on/off control
7
Main On/Main Off
R - reset
1
4
2
5
6
7
3
CLOCK CDSETRND
L
-
PROG
ONOFF
MO TU WE TH FR SA SU
X
Set function indicator
Weekday indicators
Random function indicator
AM/PM
Clock function
indicator
Disabled program
icon
ON/OFF indicator
8
8
One-Touch Countdown Button
One-Touch
Countdown
Countdown function indicator
Power Source
Red
ETW193
JUMPER
3Way
Black
Black
LOAD
COMMON
Green
HOT SWITCH
PAGE 1 PAGE 2 PAGE 3
PAGE 10 PAGE 11 PAGE 12
http://waterheatertimer.org/UPM-timers
-and-manuals.html