Total Control HDA–I/O Owner’s Manual HDA-I/O Owner’s Manual
HDA-I/O Owner’s Manual Total Control Introducing the HDA-I/O The HDA-I/O Single-Zone Amplifier is URC’s powerful and discrete amplifier! This document highlights product features, LED status conditions, basic installation, and general speaker wiring instructions. Online Support: Total Control is sold direct only and must be installed/programmed by a certified custom integrator. Table of Contents Overview ......................................................................................................
HDA-I/O Owner’s Manual Total Control Overview URC’s HDA-I/O Stream Receiver/Injector creates or receives HDA audio streams over the network. This device must be configured by a certified URC integrator to function as either a Stream Injector or Stream Receiver. As a Stream Injector, this device distributes any connected audio source (digital or analog) over the network to any available HDA controlled zone.
HDA-I/O Owner’s Manual Total Control Parts & Pieces Included with the HDA-I/O are the following: 2
HDA-I/O Owner’s Manual Total Control Front Panel Descriptions 2. Status LED: Indicates one (1) of the following: There are three (3) LEDs on the front panel of the HDA-IO: • Solid Blue: The device has been programmed with Total Control software and is ready for operation. 1. Power LED: Indicates one (1) of the following: • Solid Blue: Power has been applied to the device and it has successfully initialized.
HDA-I/O Owner’s Manual Total Control 3. Ethernet LED: Indicates one (1) of the following: 4. Reset Button: There are two (2) ways to press this button: • Solid Blue: The device has received an IP address from the local network. • Single Press: Tap the Reset button to power cycle the device. • Blinking Blue: The device is connected to the local network; however, it has not received an IP address. • Factory Reset: Press-n-hold the Reset button for 10 seconds or more.
HDA-I/O Owner’s Manual Total Control Rear Panel Description - Using as a Stream Injector 4. Analog/Digital Inputs: Both of the following inputs can be used to provide HDA “high-definition” audio streams. Only one input can be in use at any given time. Below are the available connections on the rear of the HDA-IO: 1. DC IN: Connect the supplied 12VDC adapter to this port to power the HDA-IO. 2.
HDA-I/O Owner’s Manual Total Control Rear Panel Description - Using as a Stream Receiver 4. Analog/Digital Outputs: All three (3) available outputs can be used. The HDA-IO as a stream receiver provides 3rd party audio zones with access to audio sources streaming via HDA. Below are the available connections on the rear of the HDA-IO: 1. DC IN: Connect the supplied 12VDC adapter to this port to power the HDA-IO. • Analog - RCA Style 2.
HDA-I/O Owner’s Manual Total Control 1 Installation Instructions The HDA-IO amplifier is supplied with two (2) “L” shaped brackets for mounting on the wall or secure vertical surface. 1. Insert the supplied screws into the two (2) keyed slots on the L shaped bracket (as displayed on the image at the right). This L shaped bracket can be pre-installed and the HDA-IO amplifier can be inserted afterwards. 2. Insert the supplied screws into the four (4) keyed slots for wall mounting. Keyhole Diameter: 0.
HDA-I/O Owner’s Manual Total Control 3 3. Assure that all screws have been installed securely.
HDA-I/O Owner’s Manual Total Control Network Setup When using more than one (1) HDA devices, URC’s HDA-SW5 Network Switch is REQUIRED on the local network. For more information of the HDA-SW5 Network Switch, please refer to the HDA-SW5 Owner’s Manual. Although 3rd Party AVB switches may be utilized, they are not supported by URC’s Technical Support team. Local Router HDA-SW5 Network Switch Connecting the HDA-I/O to the Network 1 1.
HDA-I/O Owner’s Manual Total Control HDA Modules Room / Zone Status URC’s HDA line of products contains several two-way modules that are accessible from any graphical user interface. These modules serve a variety of residential and commercial applications providing end-users with advanced functionality directly from any URC interface. Amplifier Status For specific instructions on how to use these HDA modules, please refer to the HDA User’s Guide.
HDA-I/O Owner’s Manual Total Control Specifications Connections Audio Inputs: ■ 1x Stereo Analog RCA style input ■ 1x Toslink (Optical) Digital Input ■ 1x Digital Coaxial Input Audio Outputs: ■ 1x Stereo Analog RCA style output Audio ■ 96 kHz / 24-bit streaming ■ Dolby Digital® and DTS® 5.1 channel Downmixing (digital inputs only) ■ Ducking input capability ■ Page event support ■ Store up to 10 .
HDA-I/O Owner’s Manual Total Control Warning! The manufacturer is not responsible for any Radio or TV interference caused by unauthorized modifications to this equipment. Changes or modifications not expressly approved by the manufacturer could void the user's authority to operate the equipment. Regulatory Information to the User • CE conformity Notice Products with “CE” marking comply EMC Directive 2014/30/EU issued by the commission of the European Community. 1.
