Use and Care Manual

ManualsBrandsUS Stove ManualsHeating, Ventilation, and Air ConditioningWonderwood 1,700 sq. ft. Wood-Burning Stove/Circulator

When ordering repair parts or options, always give the

following information as shown in this list:

1. The PART NUMBER

2. The PART DESCRIPTION

3. The MODEL NUMBER: 2941 2941B B2941 B2941B

4. The SERIAL NUMBER:________________

OWNERS MANUAL

Models 2941, B2941, 2941B, B2941B

WONDERWOOD

THERMOSTAT CONTROLLED WOOD BURNING CIRCULATOR

SAFETY NOTICE:

If this heater is not properly installed, a house fire may result.

For your safety, follow the installation directions.

Contact local building or fire officials about restrictions and

inspection requirements in your area.

CAUTION:

Read all instructions carefully before starting the installation

or operation of this heater.

Improper installation may void your warranty.

*ASSEMBLY

*INSTALLATION

*OPERATION

*REPAIR PARTS

85947M

HOW TO ORDER REPAIR PARTS

This manual will help you to obtain efficient, dependable service

from the heater, and enable you to order repair parts correctly.

Keep this manual in a safe place for future reference.

When writing, always give the full model number which is on the

nameplate attached to the inside of the cabinet door of the

heater.

WONDERWOOD

Before installing your heater, fill in the serial number of your

heater in the space provided above.

United States Stove Company

227 Industrial Park Rd.

P.O.Box 151

South Pittsburg, TN 37380

(423) 837-2100

www.USSTOVE.com

United States Stove Company

227 Industrial Park Rd.

P.O.Box 151

South Pittsburg, TN 37380

(423) 837-2100

www.USSTOVE.com

DO NOT USE THIS HEATER IN A MOBILE HOME OR TRAILER

Tested to UL 1482 & EPA Method 28A

Summary of content (10 pages)

PAGE 1
HOW TO ORDER REPAIR PARTS This manual will help you to obtain efficient, dependable service from the heater, and enable you to order repair parts correctly. OWNERS MANUAL Models 2941, B2941, 2941B, B2941B WONDERWOOD THERMOSTAT CONTROLLED WOOD BURNING CIRCULATOR Keep this manual in a safe place for future reference. When writing, always give the full model number which is on the nameplate attached to the inside of the cabinet door of the heater.
PAGE 2
CB36 BLOWER KIT TOOLS AND MATERIAL NEEDED TOOLS • • • • • Pencil 6 Foot Folding rule or tape Tin Snips Drill, hand or electric Drill bit, 1/8" dia.
PAGE 3
NOTE: DURING OPENING AND CLOSING OF THE FEED AND ASH DOORS OF THIS HEATER, IT MAY SEEM THAT THE FIT OF THE DOOR IS "TOO TIGHT". AS THE HEATER IS FIRED, THE GASKETING "SETTLES" OR "SEATS" ITSELF IN THE DOOR. THE TIGHT FIT AT THE FACTORY AND BEFORE THE HEATER'S INITIAL FIRING IS TO INSURE A GOOD SEAL AFTER THE GASKETING "SETTLES". NOTE: FOR YOUR SAFETY, WE RECOMMEND INSTALLING SMOKE DETECTORS IN YOUR HOME IF NOT ALREADY INSTALLED.
PAGE 4
heater or chimney connector. The 1 inch air space provides free air circulation. It is essential that there be openings at the top and bottom of these clearance reducers so cool air can enter at the bottom and hot air exit at the top. It is the "chimney effect" whereby when the air in the space is heated, it rises exiting from the top and being replaced by cooler air at the bottom, that makes these shields effective.
PAGE 5
EXTERIOR REPAIR PARTS CHIMNEY CONNECTION AUTOMATIC WOOD BURNING CIRCULATOR HEATER MODELS B2941, B2941B (SEE PAGE 14) (color - BLACK) REPAIR PARTS LIST KEY NO. 1 PART NO. 89635 DESCRIPTION Cabinet Door Knob QTY.
PAGE 6
FIG. 6A - Thru-The-Wall Installation EXTERIOR REPAIR PARTS AUTOMATIC WOOD BURNING CIRCULATOR HEATER MODEL NUMBER 2941, 2941B (SEE PAGE 14) (color - BROWN) NON-COMBUSTIBLE WALL THIMBLE COLLAR PIPE REPAIR PARTS LIST DAMPER BAROMETRIC DRAFT CONTROL (OPTIONAL) FLOOR PROTECTOR CLASS A UL 103HT CHIMNEY KIT INCLUDING WALL THIMBLE. FIG. 6B - Typical Masonry Chimney Installation APPROVED COWL 2 FT MIN. 10 FT. MINIMUM 6" MIN. 3 FT. MIN. APPROVED THIMBLE 60" MIN. DAMPER BAROMETRIC DRAFT CONTROL 6" MIN.
PAGE 7
REPAIR PARTS - EXTERIOR VENTING INTO A FIREPLACE (Not recommended) Many prefabricated fireplaces fall into the "zero-clearance fireplace" category. This is a factory metal fireplace with multi-layered construction. It is designed to provide enough insulation and/or air cooling so that the base, back and sides can be safely placed in close contact with combustible floors and walls.
PAGE 8
SERVICE HINTS FIREPLACE INSTALLATION Connection of the stovepipe directly into the existing masonry chimney over the fireplace opening is the only approved method. This installation performs better, yielding easy to clean and inspect for creosote. Before beginning this type of installation plan carefully; a high degree of skill is required to insure safety. Install the stovepipe as far as possible into the thimble, but not past the inside of the flue lining.
PAGE 9
CABINET DOOR KNOB ASSEMBLY The door knob is mounted inside of the cabinet door to facilitate shipping and must be reversed for proper usage. To get cabinet door open, place hand under cabinet frame (right hand side of cabinet door) and push door out. INSTALL THE CABINET DOOR KNOB USING THE STEPS BELOW: 1. Remove the machine screw and door knob (Fig. 10). 2. Place door knob on outside of cabinet door. Then place machine screw through hole and into door knob and tighten (Fig. 11).
PAGE 10
RULES FOR CONNECTOR PIPE INSTALLATION 1. The crimped end of the stovepipe fits inside the heater flue collar. Install additional pipe and elbow with the CRIMPED END TOWARD THE HEATER. This will allow any condensation in the flue to run back into the heater. Smoke will not escape when installed in this manner. 5. Seal each connector pipe joint with furnace cement. Also seal the pipe at the chimney. 6. Use 3 Sheet Metal screws at each joint to make the piping rigid. 7.