Owner's Manual
Table Of Contents
-3-
PA
11-VETTE
provides
two
ways
to
control
your
iPod
through
car
radio,
namely
P'ay'ist
Mode
and
Direct
Mode.
2-1
Direct
Mode:
Search
and
select
music
on
iPod
directly
just
as
you
would
in
portable
use.
The
music
will
play
back
through
your
car
stereo.
Use
the
track
up/down,
fast
forward,
and
reverse
buttons
on
your
radio
to
control
music
playback.
All
control
functions
on
iPod
are
available
for
use
as
well.
Please
see
section
4 in
this
manual
for
additional
information
2-2
P'ay'ist
Mode:
Operate
and
control
the
iPod
like
it is a
CD
changer.
This
mode
allows
you
to
access
up
to
five
Playlists
on
the
iPod.
This
is
also
referenced
as
the
External
Control
Mode
of
the
iPod.
Display
of
artist
and
song
title
on
radio
is
supported
by
PA11-VETTE
only
in
this
mode
of
operation.
The
detail
of
Playlist
creation
and
playback
controls
are
in
section
5
of
this
manual.
DIP
switch
#2
is
for
mode
selection
use.
"ON"
position
is
for
P'ay'ist
Mode
and
the
"OFF"
position
is
for
Direct
Mode.
Note:
Disconnect
iPod
from
PA11-VETTE
before
switching
DIP
switch
#2
for
mode
alteration.
2-3
Additional
AUX
INPUT
Option
Selection
PA
11-VETTE
interface
adaptor
is
capable
of
connecting
two
audio
sources
to
your
GM
radio,
including
the
iPod.
The
additional
audio
source
connects
to
the
RCA
input
jack
labeled
as
AUX
INPUT.
If
you
choose
to
use
AUX
INPUT,
the
DIP
switch
#1
at
the
side
of
adaptor
box
must
be
set
to
the
"OFF"
position
(factory
presets
it
at
"ON"
position).
The
audio
source
at
AUX
INPUT
can
be
accessed
at
CD
6
Track
1. CD1
to
CD
4
are
for
accessing
Playlists,
and
CD
5 is
for
accessing
all
songs
on
iPod.
Operation
of
AUX
If
the
"AUX
INPUT"
option
is
selected,
"CD
6
Track
1"
gives
access
to
the
audio
source
connected
to
AUX
INPUT
port.
Adjust
VOLUME,
BASS,
TREBLE
and
etc.
As
you
would
normally
do
for
the
other
program
sources
on
the
radio.
(Professional
installation
is
strongly
suggested.
Installation
in
the
CTS
and
SRX
are
skill
demanding
works.)
3-1
Step
1-a-
Set
the
01
P
switch
#2
to
"OFF"
position
only
if
the
Direct
Mode
is
preferred.
Step
1-b-
If
your
vehicle
is
neither
equipped
with
a
GM
XM
satellite
radio
receiver
nor
pre-wired
for
GM
XM
receiver,
got
to
step
3 directly.
Step
2-a-
Unplug
the
16-pin
connector
from
GM
XM
receiver
and
connect
it
to
the
"FEMAL"
16-pin
connector
on
USkSPEC
cable
CB-VET
(Note:
Pull-out
the
BLUE
color
lock
at
the
top
side
of
the
16-pin
connector
before
unplug
it
from
the
receiver.)
Step
2-b-
Plug
USkSPEC
CB-VET
cable's
"MALE"
16-pin
connector
to
XM
receiver.
Step
2-c-
Set
both
DIP
switch
#3
and
#4
at
side
panel
of
PA11-VETTE
to
"OFF"
position.
Be
sure
the
ACC
power
is
OFF
before
go
to
next
step.
Step
2-d-
Connect
USkSPEC
cable
CB-F12
to
the
12-pin
"MALE"
connector
CB-VET.
Plug
the
round
DIN
connector
on
CB-F12
to
PA11-VETTE
adopter
where
labeled
"RADIO".
Step
2-e-
Plug
the
blue
wire
on
USkSPEC
CB-VET
cable
to
PA
11-VETTE
adaptor
where
labeled
"XM".
Go
to
step
4 directly.
(Note: If
XM
service is not activated, the tree-at-charge
XM
preview and alert channels can be disables
by
setting DIP switch
#3
to
OFF
position
and
DIP switch
#4
to ON position.)
Step
3-a-
Remove
radio
from
dash.
Unplug
the
24
pin
and
12
pin
connectors
from
the
radio
and
connect
them
to
USkSPEC
CAS-G7i
cable.
Step
3-b-
Plug
USkSPEC
CAS-G7i
cable's
24
pin
and
12
pin
connectors
to
the
radio.
Step
3-c-
Set
the
DIP
switch
#3
to
"ON"
position
and
#4
to
"OFF"
position
Step
3-d-
Connect
CAS-F12
cable
to
G7i
cable.
Plug
the
round
01
N
connector
on
CAS-F12
to
adapter
where
labeled
"RADIO".
Go
to
Step
4.
Step
4 -
Connect
the
audio
output
of
your
auxiliary
sources
to
AUX
input
jack
on
PA11-
VETTE
adapter
box
if
the
additional
AUX
option
is
selected
by
setting
the
DIP
switch
#1
to
"OFF"
position.