Specification

with Sheetrock lightweight all purpose joint compound with dust control; however, higher-quality sandpaper will
provide optimal results.
These products typically feature a heavier-grade paper and more uniformly bonded grit, which make them
less susceptible to sandpaper packing (i.e., sanding dust caught between the back of the sandpaper and the
face of the sanding block), which can cause uneven surface sanding.
The following high-quality drywall sandpapers are recommended for use with
Sheetrock lightweight all
purpose joint compound with dust control:
– 3M
™
SandBlaSter
™
Bare Surfaces Sandpaper (purple)
– Johnson Abrasives
Smooth-kut
™
Paper (black)
– Sancap Abrasives
Golden touch
®
Paper
– Mercer Abrasives Premium Green Drywall Paper
Decorating For painting and decorating, follow manufacturer directions for materials used. All surfaces, including applied
joint compound, must be thoroughly dry, dust free and not glossy. Sand all joints, fasteners and beads before
decorating. Remove any sanding dust from surfaces. If smoothing and dry sanding, use 150-grit sandpaper or
220-grit abrasive mesh cloth, or finer.
Sheetrock
®
brand First Coat
™
primer or a comparable interior latex wall
primer, that will equalize the texture and porosity variation between the joint compound and the gypsum board
face paper, should be applied and allowed to dry before painting, texturing or wallpapering. Walls to be covered
with wallpaper or vinyl wallcovering should be sealed per wallcovering manufacturer's instructions.
Where walls and ceilings will be subject to severe artificial or natural side lighting and/or decorated with
gloss paint (eggshell, semi-gloss or high-gloss), skim-coat gypsum panels with
Sheetrock
®
brand conventional
weight all purpose joint compound or
cover coat
®
compound to improve fastener concealment and minimize
decorating problems such as joint banding. Skim coating fills imperfections in joint work, smoothes the paper
covering of drywall panels and provides a uniform surface for priming and painting. As an alternative to skim
coating, apply
Sheetrock
®
brand tuff-hide
™
primer-surfacer.
For large projects a mock up of the selected system (substrate, joint compounds and finish coatings)
should be evaluated by all responsible parties for suitability, appearance and durability before any large-scale
applications begin.
Product Data
Material: Latex-type formulation.
Types: Hand or mechanical application.
Freezing Sensitivity: Protect from freezing.
Coverage: Approx. 9.4 gal./1,000 ft.
2
(38.3 L/100 m
2
) of gypsum panels.
Compliance with Standards: Meets ASTM Standard C475.
Packaging: 3.5-gal. (13.2 L) pail/3.5-gal. (13.2 L) carton.
VOC Content: <2g/L.
Storage Store in dry location and protect from moisture, freezing and exposure to extreme heat and direct sunlight.
Keep tightly sealed. Shelf life of unopened container under protected storage conditions is up to nine months.
Check product date codes periodically. Rotate stock on first-in, first-out basis.
When lifting joint compound packages, observe proper lifting techniques. Keep the load close to your
body and use your legs, not your arms, to lift. Use mechanical assistance such as pallet lifters or hand dollies
wherever possible. Confine manual lifting and carrying to the shortest possible distance.
Submittal
Job Name
Approvals:
Contractor Date
Manufactured by
United States Gypsum Company
550 West Adams Street
Chicago, IL 60661
(800) USG.4YOU (874.4968)
usg.com
J1832/rev. 6-09
© 2009, United States Gypsum Company
Printed in U.S.A.
Gypsum Company: cover coat,
P
luS 3, Sheetrock, tuff-hide. 3M
and
SandBlaSter are trademarks
of 3M Company.
Smooth-kut is a
trademark of Johnson Abrasives.
Golden touch is a trademark of
Sancap Abrasives, Inc.
Note
Products described here may not be
available in all geographic markets.
Consult your U.S. Gypsum Company
sales office or representative for
information.
Notice
We shall not be liable for incidental
or consequential damages, directly
or indirectly sustained, nor for any
loss caused by application of these
goods not in accordance with current
printed instructions or for other than
their intended use. Our liability is
expressly limited to replacement
of defective goods. Any claim shall
be deemed waived unless made in
writing to us within thirty (30) days
from the date it was or reasonably
should have been discovered.
Safety First!
Follow good safety and industrial
hygiene practices during handling
and installation of all products
and systems. Take necessary
precautions and wear the
appropriate personal protective
equipment as needed. Read
material safety data sheets and
related literature on products before
specification and/or installation.
ingested, call physician. Do not use
if material has spoiled, i.e., there is a
moldy appearance or an unpleasant
odor. Close container and discard
properly.
Product safety information:
[phone] or www.usg.com
KEEP OUT OF REACH OF CHILDREN.
Product Information
See usg.com for the most
up-to-date product information.
Trademarks
The following trademarks used
herein are owned by United States
CAUTION!
Dust generated from sanding product
may cause irritation to eyes, skin,
nose, throat and upper respiratory
tract. Avoid irritation by reducing
exposure to dust. Use in a well-
ventilated area or provide sufficient
local ventilation. If dusty, wear a
NIOSH/MSHA-approved respirator.
Wear eye protection. If eye contact
occurs, flush thoroughly with water
for 15 minutes. If irritation persists,
call physician. Wash with soap and
water after use. Do not ingest. If