Installation Instructions

ManualsBrandsUTC Fire & Security ManualsElectronicsKeypad with proximity reader transmitter

AL-111X Arming Station

Product Summary

AL-111X Arming Station

Installation and Programming Instructions

Models:

AL-1110 - two-line LCD AL-1111 - four-line LCD

AL-1115 - two-line LCD with Smart Card reader AL-1116 - four-line LCD with Smart Card reader

Used with Alliance control panels, AL-111X Series RAS are used for controlling security system alarm and access

functions. Product features include:

• Beeper

• Integrated tamper switch

• Two- or four-line Liquid Crystal Display (LCD)

• Multiple text formats for four-line LCD models (AL-1111 and AL-1116)

• Embedded Smart Card Reader (AL-1115 and AL-1116)

• Access and system status Light Emitting Diodes (LED)

• The RAS may be used up to 5,000 feet (1.5 km) from the control panel or four-door controller DGP.

• One open collector output is provided to drive a small relay, LED, etc. One input is provided for an egress function.

• Plastic hinged cover

Allian

Figure 1.

Status LEDs

LCD Display

Keypad

Smart Card Reader

(AL-1115 and

AL-1116 only)

behind keypad

Area LEDs

Cover

Locking

Screw

DIP Switches

COMMS

Terminal

Tamper

Switch

Cable

Entry

Cable

Entry

Mounting

Plate

Mounting

Screw

Holes

Cable

Entry

Power

Fault

Access

Alarm

Summary of content (8 pages)

PAGE 1
g Alliance Power Fault AL-111X Arming Station Installation and Programming Instructions Access Alarm Cable Entry Status LEDs LCD Display Mounting Screw Holes COMMS Terminal Keypad DIP Switches Smart Card Reader (AL-1115 and AL-1116 only) behind keypad Cable Entry Mounting Plate Cable Entry Tamper Switch Area LEDs Locking Screw Cover Figure 1.
PAGE 2
Removing the Cover and Mounting Plate The RAS cover is hinged at the bottom. To open, grasp the cover at the sides or the top and pull gently - the cover will swing down on its pins (see Figure 1). The cover may be fully removed by gently prizing one of the pins away from the body of the RAS and pulling. The metal mounting plate at the back is held by a locking screw (see Figure 1). To remove the mounting plate, loosen the screw by at least 8mm (0.315 in.
PAGE 3
Connections A terminal block on the back of the RAS (see Figure 1) is used for the COMMS (System BUS) connection. System BUS Connection (D+ and D-) The RAS is connected to the Alliance panel via the RS-485 System BUS, up to 5,000 feet (1.5 km) from the control panel or the four-door controller DGP. It is recommended to use a 2-pair twisted, shielded data cable (Beldon 8723). The shield of any System BUS cable must be connected to system ground at one end only.
PAGE 4
Status LED Indications AL-111X RAS have four status LEDs above the LCD panel (see Figure 1): • • • • Power - The Green LED illuminates when the control panel is powered by the AC supply. Fault - The Yellow LED illuminates to indicate detection of a system fault. Access - The Blue LED flashes when access to an area assigned to the RAS is granted. It also flashes once when a card is badged at an AL-1115 or AL-1116 (subject to Valid Card Flashing Programming).
PAGE 5
Programming Introduction The AL-111X Series has a number of options that are programmable at the time of installation to help integrate the keypad into the local environment. In particular, the AL-1115 and AL-1116 RAS are fitted with a Smart Card reader. If used in the default “secure” mode, the reader must be configured via a reader configuration card before it can be used.
PAGE 6
Menu Option Description 1 - Access LED Controls the blue Access LED (enabled by default). The blue Access LED may be disabled if not required. 2 - Night Light A dimly lit keypad backlight provides the night light to easily locate the keypad in dark locations (enabled by default). The night light may be disabled if not required. 3 - Keypad Backlight The keypad backlight turns on bright for night-time illumination of the key labels (enabled by default).
PAGE 7
Offline Mode If the RAS has power available but loses communications with the panel, the RAS will go into offline mode. In this mode, all LEDs will flash at the slow rate and the LCD will display “-System Fault-”. This condition may be caused by the following: • • RAS is set to an address that is not polled by the panel or 4-door controller DGP. The D+ or D- wire is dissconnected. Unused Keys There are four keys on the keypad reserved for future use.
PAGE 8
FCC Compliance for AL-1115/AL-1116 This device complies with Part 15 of the FCC rules. Operation is subject to the following conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. 3. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.