Installation Guide

ManualsBrandsUtilitech Pro ManualsLighting & FansDesigner 14.12-in Hardwired/Plug-In Under Cabinet LED Light Bar

Utilitech & UT Design® are registered

ITEM #0378137, 0378139, 0378141

MODEL #GU0414CL-BA-I

GU0622CL-BA-I

GU0830CL-BA-I

DESIGNER LED

CABINET LIGHT

Français p. 8

Español p. 15

Questions, problems, missing parts? Contact the customer service department at

1-866-994-4148, 8 a.m. - 6 p.m., EST, Monday - Thursday, 8 a.m. - 5 p.m., EST, Friday.

ATTACH YOUR RECEIPT HERE

Serial Number: Purchase Date:

Summary of content (7 pages)

PAGE 1
ITEM #0378137, 0378139, 0378141 DESIGNER LED CABINET LIGHT MODEL #GU0414CL-BA-I GU0622CL-BA-I GU0830CL-BA-I Utilitech & UT Design® are registered trademarks of LF, LLC. All Rights Reserved. Français p. 8 Español p. 15 ATTACH YOUR RECEIPT HERE Serial Number: Purchase Date: Questions, problems, missing parts? Contact the customer service department at 1-866-994-4148, 8 a.m. - 6 p.m., EST, Monday - Thursday, 8 a.m. - 5 p.m., EST, Friday.
PAGE 2
PACKAGE CONTENTS A C B PIECE A B C D D DESCRIPTION Fixture Wire Compartment Cover Power Cord Linking Cord QUANTITY 1 1 1 1 HARDWARE CONTENTS (shown actual size) AA Wood Screw Qty. 2 BB Wire Nut CC Strain Qty. 1 Relief (not shown to size) Qty. 3 WARNINGS AND CAUTIONS WARNING • Please read and understand this entire manual before attempting to assemble, operate or install the product. CAUTION • This fixture is dimmable with a forward phase electronic dimmer.
PAGE 3
IMPORTANT SAFETY INSTRUCTIONS insulation may go unnoticed. To prevent fire danger, do not run cord behind walls, ceilings, soffits, cabinets, or a similiar permanent structure where it may be inaccessible for examination. Cords should be visually examined periodically and immediately replaced when any damage is noted. 17. You must limit your installation to a total of 60 LED fixtures in any given circuit chain.
PAGE 4
INSTALLATION INSTRUCTIONS 3. KEYHOLE INSTALLATION: Position the fixture (A) and mark the location of the narrow ends of the keyhole slots onto the mounting surface. Drill a 1/16 in. pilot hole into the marked screw locations. You can also use an awl or nail to dimple the screw holes. While holding the fixture in place tighten the wood screws (AA) with a phillips head screwdriver until the fixture is flush with the surface. 3 A Hardware Used AA AA Wood Screw x2 4 A B 4.
PAGE 5
DIRECT WIRE INSTALLATION 2. Once you have determined the position the fixture will be mounted, mark the corresponding knock-out closest to your supply wire feed and remove it. CAREFULLY REMOVE THE KNOCK-OUT BY HAMMERING A FLATHEAD SCREWDRIVER OR PUNCH UNTIL THE SURFACE BREAKS. If the knock-out did not break free, use pliers and bend it back and fourth until it snaps off. 3. Attach the supplied strain relief (CC) by inserting the threaded end (from outside the fixture) through the knock-out.
PAGE 6
DIRECT WIRE INSTALLATION 8. For safety and proper operation, your fixture must be properly grounded. If you are unfamiliar with the methods of properly grounding your fixture, consult a qualified electrician. A copper or green ground wire is pre-attached to your fixture. If your electrical box is made of plastic and/or has a green or bare copper grounding wire inside, connect the ground wire to the fixtures’ ground wire lead using one of the wire nuts.
PAGE 7
CARE AND MAINTENANCE You may want to periodically clean the fixture using a mild, non-abrasive glass cleaner and soft cloth. Do NOT use solvents or cleaners containing abrasive agents. When cleaning the fixture, make sure you have the power turned off and do not spray liquid cleaner directly onto the LEDs, fixture, diffuser, or wiring. TROUBLESHOOTING Minor problems often can be fixed without the help of an electrician.