Installation Guide

ManualsBrandsUtilitech Pro ManualsLED Under Cabinet LightsUC1051-AL3-22LF0-U

ITEM #0774383, 0774384, 0774385

MODEL #UC1051-AL3-14LF0-U,

UC1051-AL3-22LF0-U,

UC1051-AL3-30LF0-U

LED CONVERTIBLE

UNDER CABINET BAR

Français p. 8

Español p. 15

Questions, problems, missing parts? Contact the customer service department at

1-866-994-4148, 8 a.m. - 6 p.m., EST, Monday - Thursday, 8 a.m. - 5 p.m., EST, Friday.

ATTACH YOUR RECEIPT HERE

Serial Number: Purchase Date:

Lowes.com

AB15828

Summary of content (7 pages)

PAGE 1
ITEM #0774383, 0774384, 0774385 LED CONVERTIBLE UNDER CABINET BAR MODEL #UC1051-AL3-14LF0-U, UC1051-AL3-22LF0-U, UC1051-AL3-30LF0-U Français p. 8 Español p. 15 ATTACH YOUR RECEIPT HERE Serial Number: Purchase Date: Questions, problems, missing parts? Contact the customer service department at 1-866-994-4148, 8 a.m. - 6 p.m., EST, Monday - Thursday, 8 a.m. - 5 p.m., EST, Friday. AB15828 1 Lowes.
PAGE 2
PACKAGE CONTENTS A C B D PART A B C D E E DESCRIPTION Fixture Wire Compartment Cover Locking Tab Power Cord Linking Cord QUANTITY 1 1 2 1 1 HARDWARE CONTENTS (shown actual size) AA Wood Screw Qty. 2 BB Strain Relief Qty. 1 SAFETY INFORMATION WARNING • Please read and understand this entire manual before attempting to assemble, operate or install the product. CAUTION • This fixture is dimmable with a forward phase electronic dimmer.
PAGE 3
SAFETY INFORMATION 15. Do not use an extension cord. Use power strip with integral overcurrent protection to supply power to the fixture. 16. The total wattage of ALL the fixtures linked together in one chain should NOT exceed 360 watts. Exceeding the total wattage will result in a hazardous situation. Fixture wattage can be found on back of fixture. IMPORTANT: These LED light heads use light emitting diodes to provide light.
PAGE 4
TRADITIONAL MOUNTING INSTALLATION 1. Locate the mounting keyhole slots on the back of the fixture. Measure the center-to-center distance to determine the distance the wood screws need to be installed. Measure and mark the corresponding placement on the mounting surface. NOTE: The wire compartment cover can be opened on the fixture and trace the perimeter of keyhole slots. 2. Use a nail or awl to dimple the surface to help guide the wood screws (AA).
PAGE 5
DIRECT WIRE INSTALLATION 2. Located on each side of the fixture are two locking tabs (C) that lock the cover to the wire compartment cover (B) in place. Disengage each tab by carefully prying them out with a flathead screwdriver (not included) far enough to remove the cover to expose the wire connections and keyhole slots inside. DO NOT try to remove tabs from the fixture. 3. Determine which corresponding knock-out is closest to the supply wire feed and remove it.
PAGE 6
DIRECT WIRE INSTALLATION 7. Connect the supply leads from flexible whip or NM cable to the fixture leads using the pre-installed push-in connectors as per the illustration. Insert the black supply lead into the open hole in the push-in connector pre-attached to the black fixture wire. Insert the white supply lead into the open hole in the push-in connector pre-attached to the white fixture wire. All wire connections should be made and stowed inside wire compartment of the fixture.
PAGE 7
LINKING INSTRUCTIONS 4. Insert the opposite end of the linking cord into the “Power-In” port of the additional unit. NOTE: Each light can be individually operated by the on/off switch located on each fixture. 4 E 5. Restore power to the powered unit. CARE AND MAINTENANCE Periodically clean the fixture using a mild, non-abrasive glass cleaner and soft cloth. Do NOT use solvents or cleaners containing abrasive agents. When cleaning the fixture, make sure the power is turned off.