Installation Guide

1. The fixture (A) can be mounted without utilizing pilot holes.
Firmly hold the fixture against the mounting surface and begin
turning the mounting screws until they are fully driven in and the
fixture is firmly attached to the mounting surface. NOTE: DO
NOT overtighten the screws, as it may result in damage to the
fixture or the mounting surface. Direct Wire Installation Only:
Determine the fixture location, but do not mount until the wiring
steps are completed.
EASY MOUNTING INSTALLATION
MOUNTING OPTIONS
1
WARNING
• Please read and understand this entire manual before attempting to assemble, operate
or install the product.
CAUTION
• This fixture is dimmable with a forward phase electronic dimmer. Dimmers tested to be
compatible with this fixture are the Lutron: Diva® C
•
L™: DVWCL-153P or DVCL-153P,
Lumea® C
•
L™: LGCL-153P, and Toggler® C
•
L™: TGCL-153P8. If unfamiliar with electrical
installations, it is recommended a qualified electrician do the installation.
• This device complies with Part 15 of the FCC rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
There are two methods to mount the fixture to a cabinet. The first is the EASY MOUNTING
INSTALLATION method that uses the pre-installed screws located at both ends of the fixture. The
second is the TRADITIONAL MOUNTING INSTALLATION method, which utilizes the keyhole slots
located on the backside of the fixture.
Before mounting, find a suitable location to mount the fixture that
will reach the power supply (within 5 feet) or to reach adjoining
fixture (within 18 inches). The fixture has two power ports located
at each end of the fixture. The “Power-In” port is located on the
end next to the on/off switch and is used to connect the fixture to
a power supply. The “Power-Out” port is located at the opposite
end and is used to link power to additional fixtures connected
together.
WARNING: To reduce the risk of FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS:
1. For INDOOR USE ONLY.
2. Not intended for installation in plastic cabinets.
3. The mounting surface should be flat and sturdy enough to support the fixture.
4. Do NOT mount the fixture to cabinets having a material thickness less than 1/4 in.
5. Not intended for recessed installation in ceilings or soffits.
6. Do NOT use in wet locations.
7. Do NOT use for illumination of aquariums.
8. Do NOT mount over sinks or stoves.
9. Do NOT touch, operate, or install fixture while in contact with water.
10. Do not remove the protective LED lens or touch the LEDs at any time.
11. Use a soft cloth to clean the diffuser and/or fixture.
PLUG-IN/LINKING SAFETY INFORMATION:
12. Do NOT attempt to install while plugged in.
13. Use only insulated staples or plastic ties to secure the power or linking cords.
14. The National Electrical Code (NEC) does not permit cords to be concealed where damage to
insulation may go unnoticed. To prevent fire danger, do not run cord behind walls, ceilings, soffits,
cabinets, or similiar permanent structures where it may be inaccessible for examination. Cords
should be visually examined periodically and immediately replaced when any damage is noted.
15. Do not use an extension cord. Use power strip with integral overcurrent protection to supply
power to the fixture.
16. The total wattage of ALL the fixtures linked together in one chain should NOT exceed 360 watts.
Exceeding the total wattage will result in a hazardous situation. Fixture wattage can be found on
back of fixture.
IMPORTANT: These LED light heads use light emitting diodes to provide light. LEDs are electronic
semiconductors and do not have a filament that can burn out like an ordinary light bulb. As such, the
LED light heads can last up to 50,000 hours when used intermittently, and therefore, never need
replacing.
SAVE THESE INSTRUCTIONS IN A LOCATION CLOSE TO THE LIGHT FIXTURE TO REFER TO
THEM AT A LATER TIME. Before installation, plug in fixture to a 120 V, 60 Hz electrical outlet to check
for proper operation. Then, unplug and begin the installation.
SAFETY INFORMATION
Power-Out
Port
Power-In
Port
A
PREPARATION
Before beginning assembly of product, make sure all parts are present. Compare parts with
package contents list and hardware contents list. If any part is missing or damaged, do not
attempt to assemble the product.
Estimated Assembly Time: 25 minutes
Tools required for assembly (not included): Phillips screwdriver, flathead screwdriver, pliers.
Lowes.com
3