Installation Guide

MODEL: 13111,13112,13113,15619,15672,15674,15675,15679,16170,16172,105849,105851,105895...
READ & SAVE
INSTALLATION & OPERATION INSTRUCTIONS
ASSEMBLY TIME: 30~60 minutes.
TOOLS & MATERIALS REQUIRED
° Screwdriver ° Wire Connectors
° Insulated Pliers ° Keyhole Saw
° Ladder ° Pencil
° Hammer
° Wiring Supplies as required by Electrical Code
GENERAL
1. To ensure the success of the installation, be sure to read these
instructions and review the diagrams thoroughly before
beginning.
2. All electrical connections must be in accordance with local
codes, ordinances, and the National Electric Code. If you are
unfamiliar with methods of installing electrical wiring, secure the
services of a qualified licensed electrician.
3. This Non-IC fixture is intended for use in recessed cavities or
suspended ceilings where the recessed portions of the fixture,
other than at points of support, are at least 1/2" (1.27 cm) from
combustible material and 3" (7.6 cm) from thermal insulation.
(Fig.1)
4. This fixture can be converted to be used in Insulated Ceiling
application also by using INSULATED CEILING
CONVERSION BOX # model 105896 (NOT INCLUDED)
5. This fixture is thermally protected. A blinking of the bulb in the
fixture indicates thermal insulation has been placed too close to
the fixture, an incorrect lamp has been installed, or heat from
another source is affecting the fixture. Always double-check
your intended locations prior to making the installation holes.
6. Before starting the installation, disconnect the power by turning
off the circuit breaker or by removing the appropriate fuse at the
fuse box. Turning the power off using the light switch is not
sufficient to prevent electrical shock.
7. Check if the power source is suitable for the added electrical
load.
8. If the power source is suitable, but not at the same intended
location of the fixture, run the appropriate wiring (not included)
to the intended location. Leave an additional 18" (45.8 cm) of
wiring for installation in a pre-existing ceiling with no or limited
access.
UNPACK THE FIXTURE
Check the contents of the box. You should receive:
1 -Housing (can) 1-Template
1 -Fixture trim 2-Pre attached remodel clips
PREPARE THE FIXTURE AND MOUNTING LOCATION
NOTE: First turn off electricity.
Pre-existing ceiling remodel applications with no or
limited access:
1.
Choose the location for the fixture, taking into consideration
the location of the joists, the 6-1/2” (16.5 cm) depth
clearance, electrical supply, and the 1/2” clearance from the
joists or any other combustible material.
2. Cut a 3-3/8” (85 mm) hole in the ceiling (Fig 2) after choosing
the appropriate location. A template is provided to assist in
cutting hole.
3. Pull the additional 18" (45.8 cm) of wiring from the hole into
the room and make the electrical connections to the housing
(Fig 3).
4. Adjust the preformed “L” shaped ceiling tabs in outward
position. This will prevent the housing from being pushed up
into the ceiling while installing the trim. (Fig 4)
5. Press the top portion of the pre attached remodel clips
against the side of the housing. (Fig 5). Push the housing
with the top side of the clips through the hole until you feel
tension. Continue to push the housing until it snaps into place
(Fig 6).
For new construction prior to the installation of the
ceiling:
1. Remove pre attached 2 remodel clips from the housing.
2. Plaster Frame Kit model 105895 (NOT INCLUDED) will be
needed to attach fixture to the joist. Plaster frame kit includes 2
sets of Hanger bars and 2 sets of snap in brackets. Secure the
plaster frame kit to the housing as follows:
a) Determine the ceiling thickness.Refer to Figure 7 and
determine appropriate slots on housing to match ceiling
thickness. Install snap in bracket in the slots
accordingly(Fig 7A). Press the snap in bracket and make
sure it is secured properly in the slots.
b) The hanger bars can be extended on each side of the
housing towards the joists where they are hammered into
position at ceiling level (Fig 7A) Proceed to Electrical
Connections( Fig 3).
c) Press the L shape Ceiling tabs inwards towards the
center of the housing, install the ceiling material (Fig 8).
Adjust the preformed “L” shaped ceiling tabs in outward
position. This will prevent the housing from being pushed
up into the ceiling while installing the trim.
ELECTRICAL CONNECTIONS
WARNING-Use supply wires rated 90 degrees C.
1.
Detach the Junction box from the housing by removing J-box
securement screw. Attach the appropriate wiring method from
the power source to the hole in the junction box( Fig 3)
2. Connect the white wire(s) from the fixture to the white wire
(neutral) of the supply circuit. Connect the black wire(s) from
the fixture to the black wire (hot) of the supply circuit. Connect
the green (or bare copper) colored wire to the grounding
conductor of the supply circuit. Use UL/CSA Listed wire
connectors suitable for the size, type, and number of
conductors. No loose strands or loose wires should be
present. Secure wire connectors with electrical tape.
3. Secure the junction box onto the top of the housing by
inserting the slotted end in first and then screwing the tab end
into the housing with the screw provided, making sure that all
wiring is contained within the box.
FINAL ASSEMBLY
Trim Assembly:
1. Mount the bulb in the socket, secure bulb in the Trim and push
the trim towards the housing (Fig9).
CAUTION: Use only JDR-C/GU10 Maximum 50 watt Bulb( included)
DO NOT EXCEED RECOMMENDED MAXIMUM WATTAGE
Restore electrical power.
For electrical connection inspection, turn off the electricity.
Remove the trim from the housing and pull the housing out
gently with the pull strap (Fig 10). Repeat all the above steps
for reinstallation.
USE & MAINTAINS
1. This unit is suitable for indoor use only.
2. To avoid risk of electric shock, fire, do not modify this fixture, if
any modification is made it may render the product unsafe.
3. Clean the surface finish only using water and mild soap dry
with a soft cloth. Never use rough cloth, abrasives or chemical
cleaners containing acids or harsh solvents.
TROUBLE SHOOTING TIPS
1. If the fixture fails to operate normally, please check the bulb,
and wire and wire connections. Cycling on and off may be
because of over-lamping.
2. For any missing or damaged parts or problems related to your
fixture, you may call our free customer service line for help:
For USA: 1-800-USA-LAMP
For CANADA: 1-800-498-4704
Office hours: Mon.-Fri. 9am-5pm Eastern time.
PRINTED in CHINA