Installation Guide

ManualsBrandsUtilitech ManualsLighting & FansWhite Ceiling Fluorescent Light ENERGY STAR (Common: 4-ft; Actual: 4-ft 0.12-in )

WARNING

CAUTION

Before beginning installation of product, make sure all parts are present. Compare parts with package

contents list and diagram above. If any part is missing or damaged, do not attempt to assemble, install or

operate the product. Contact customer service for replacement parts.

Estimated assembly time is 45 minutes.

Tools required for assembly: Eye protection, screwdriver, ladder

Helpful too

ls: Wire cutter, pliers, stud finder, wire stripper, drill with 1

/4 in. bit.

WARNINGS AND CAUTIONS

PREPARATION

LOW PROFILE FLUORESCENT WRAP

NVOLVENTE FLUORESCENTE DE BAJO PERFIL

(page 6)

ITEM # 184346

MODEL # PLW432R8

Questions, problems, missing parts? Before returning

to your retailer, call our customer service department at

1 (866) 994-4148, 8:00 am - 6:00 pm EST, Monday - Thursday,

Friday 8:00 am - 5:00 pm EST

Instant-on 120 Volt, 60 Hz electronic

For installation in dry or damp

ballast with minimum 0°F start

residential applications

LAMPE FLUORESCENTE EXTRA-PLATE

(página 4)

Clear prismatic diffuser

White steel fixture assembly

White steel ballast cover

Part

Description Quantity

PACKAGE CONTENTS

F32T8, 32 watt, 4 ft. lamps

Screws or toggle bolts

Wire nuts

Part Description

Quantity

ADDITIONAL PARTS REQUIRED (not provided)

Electrical tape

Read all safety precautions and installation instructions carefully before installing or servicing this fixture.

Failure to comply with these instructions could result in potentially fatal electrical shock and/or property damage.

It is recommended that a qualified electrician perform all wiring. This fixture must be wired in accordance

with all national and local electrical codes.

To reduce the risk of electrical sho

ck, and to assure proper operation, this fixture must be adequately

grounded.

Do not handle any energized fixture or attempt to energize any fixture with wet hands or while standing on a

wet or damp surface or in water.

Disconnect electrical power before installing or servicing any part of this fixture.

Do not use with dimmer switch of any kind.

8060325 R2

Summary of content (7 pages)

PAGE 1
ITEM # 184346 LOW PROFILE FLUORESCENT WRAP Instant-on 120 Volt, 60 Hz electronic ballast with minimum 0°F start LAMPE FLUORESCENTE EXTRA-PLATE (página 4) ENVOLVENTE FLUORESCENTE DE BAJO PERFIL (page 6) MODEL # PLW432R8 For installation in dry or damp residential applications PACKAGE CONTENTS Part A Description White steel fixture assembly B White steel ballast cover Clear prismatic diffuser C Questions, problems, missing parts? Before returning to your retailer, call our customer service departme
PAGE 2
INSTALLATION INSTRUCTIONS 1. Separate the diffuser from the fixture body by shifting it to one side and pulling it from assembly. (Fig. 1-A & B) 2. Separate the ballast cover from the fixture body by squeezing it in at dimples and pulling it from the assembly. (Fig. 1-D) B A 3. Plan the mounting. NOTE: When mounted, the mounting hardware must secure the fixture solidly to the ceiling. (Fig. 4) Screws must penetrate joists or toggle bolts must be placed through the ceiling boards. (Fig.
PAGE 3
CARE AND MAINTENANCE Periodically, dust the diffuser (inside and out) with a clean, dry cloth. Wipe clean with a slightly damp cloth as needed. Never use abrasive cleansers. TROUBLESHOOTING Problem Light fails to illuminate. No flickering. Light flickers blinks or lights ends only. Possible Cause 1. Fixture wiring problem. 2. No power or failed switch. 3. Worn-out lamp(s). 4. Failed ballast. 1. Fixture not properly grounded. 2. Wrong lamp(s). 3. One or more failing lamps. 4. Failing ballast.
PAGE 4
ARTICLE N o 184346 LAMPE FLUORESCENTE EXTRA-PLATE Ballast électronique à allumage instantané de 120 volts, 60 Hz, température minimale d’allumage : -18 °C Pour l’installation en milieu résidentiel sec ou humide CONTENU Description Luminaire blanc en acier Pièce A B C Couvercle de ballast blanc en acier Diffuseur prismatique transparent MODÈLE No PLW432R8 « Avez-vous des questions à poser, éprouvez-vous des difficultés ou vous manque-t-il des pièces? Avant de retourner chez le détaillant, veuillez commu
PAGE 5
DIRECTIVES D’INSTALLATION 1. Enlever le diffuseur en le poussant d’un côté du luminaire et en le dégageant de l’autre côté (fig. 1-A et B) 2. Enlever le couvercle du ballast en le comprimant aux fossettes et en le tirant (fig. 1-D). 3. Planifier l’assemblage. REMARQUE : Les pièces de fixation doivent être assez robustes et installées de façon à retenir solidement le luminaire au plafond (fig. 4).
PAGE 6
ARTICULO # 184346 ENVOLVENTE FLUORESCENTE DE BAJO PERFIL Regulador electrónico de encendido instantá neo de 120 voltios y 60 Hz con encendido a un mínimo de 0°F Para aplicaciones residenciales en lugares secos o húmedos CONTENIDO DEL PAQUETE Pieza A Descripción Estructura de acero en blanco B Cubierta del regulador de acero en blanco Difusor prismático transparente C MODELO # PLW432R8 ¿Preguntas, problemas, piezas faltantes? Antes de regresar a la tienda, llame a nuestro departamento de servicio al
PAGE 7
INSTRUCCIONES DE INSTALACION 1. Separe el difusor del cuerpo de la lámpara moviéndolo hacia un lado y halándolo para separarlo de la unidad. (Fig. 1-A y B) 2. Separe la cubierta del regulador del cuerpo de la lámpara apretando las pestañas y halándola para serparla de la unidad. (Fig. 1-D) 3. Planifique el montaje: NOTA: Al montarse, las herrajerías de montaje deben fijar firmemente la lámpara al techo. (Fig.