ITEM #0831385 TM DECORATIVE VENTILATION FAN WITH LED LIGHT MODEL #7105-05 Français p. 13 Español p. 25 ATTACH YOUR RECEIPT HERE Serial Number________________ Purchase Date_______________ Questions, problems, missing parts? Before returning to your retailer, call our customer service department at 1-866-994-4148, 8 a.m. - 6 p.m., EST, Monday - Thursday, 8 a.m. - 5 p.m., EST, Friday.
TABLE OF CONTENTS Product Specifications.........................................................................................................................2 Package Contents...............................................................................................................................3 Hardware Contents.............................................................................................................................3 Safety Information..........................................
PACKAGE CONTENTS D A E B F C G I H PART A B C D E DESCRIPTION Fan Housing LED Panel Mounting Bar LED Panel Rim Glass Globe QTY 1 1 1 4 1 PART F G H I DESCRIPTION Suspension Bracket I Suspension Bracket II Suspension Bracket III Duct Connector HARDWARE CONTENTS (not shown actual size) AA BB CC DD EE Long Wood Screw Short Machine Screw Small Machine Screw Metal Washer Long Machine Screw Qty. 9 Qty. 5 Qty. 4 Qty. 5 Qty.
SAFETY INFORMATION READ AND SAVE THESE INSTRUCTIONS Please read and understand this entire manual before attempting to assemble, operate or install the product. 1. Always disconnect the power supply prior to servicing the fan, motor or junction box. 2. Installation work must be carried out by a qualified person(s) in accordance to all local and safety codes including the rules for fire-rated construction. 3.
PREPARATION Estimated Assembly Time: 60 minutes Tools Required for Assembly (not included): Hammer, Flathead Screwdriver, Duct Tape, Phillips Screwdriver, Utility Knife Helpful Tools (not included): Electric Drill, Drill Bits WARNING: Turn off electricity at breaker box before beginning installation. Carefully remove unit from carton. Check area above installation location to be sure that wiring can run to the planned location and that duct work can be run and the area is sufficient for proper ventilation.
NEW CONSTRUCTION ASSEMBLY INSTRUCTIONS BEFORE INSTALLATION: Turn off power source. Review all safety precautions. 1. 1 A Place LED panel mounting bar (B) on fan housing (A) and attach where indicated using long machine screws (EE). Hardware Used EE Long machine screw EE EE x4 B 2. Attach the duct connector (I) to the fan housing (A). 2 I A 3. I nsert suspension bracket I (F) into the bracket cover on the duct connector side.
NEW CONSTRUCTION ASSEMBLY INSTRUCTIONS 5. Secure the suspension brackets (F, G) to fan housing (A) using small machine screw (CC). 5 A CC Hardware Used CC Small machine screw CC x3 F G CC 6. Remove wiring box cover (6.1). Pull the house wires through the wire box cover hole. Using a quick connector, secure 120 V AC house wiring from the wall switch to the fan as shown in the wiring diagram on page 5. 14 AWG is the smallest conductor that should be used for branch-circuit wiring.
NEW CONSTRUCTION ASSEMBLY INSTRUCTIONS 9. Secure the LED panel (C) to the fan housing (A) using 4 short machine screws (BB) and metal washers (DD). 9 A Hardware Used BB Short machine screw x4 DD Metal washer x4 C DD BB 10. Choose which rim (D) finish suits your room. Lay glass globe (E) into chosen rim (D). 10 D E 11. Line up the three notches around the outside of the LED panel (C) with the three clips on the rim (D).
EXISTING CONSTRUCTION ASSEMBLY INSTRUCTIONS MUST HAVE ACCESS TO THE ATTIC 1 1 10 4 5 6 If this fan is not replacing an old fan, be sure to cut a 9 in. x 9 in. opening for the fan housing (A). 9 2. 8 Measure the opening to ensure it is large enough to accommodate the new fan housing (A) (9 in. x 9 in.). 7 1. 11 BEFORE INSTALLATION: Turn off power source. Review all safety precautions. Remove existing fan. 2 9" MAKE SURE ONE EDGE OF THE OPENING IS FLUSH WITH JOIST FOR INSTALLATION FROM BELOW.
EXISTING CONSTRUCTION ASSEMBLY INSTRUCTIONS 6. Secure the fan housing (A) to joist with suspension brackets (F, G, H) using long wood screws (AA). 6 A Note: Bottom of fan housing should be flush with the bottom of the joist. When mounted correctly, the LED panel mounting bar (B) will hang below the ceiling board. Optimum spacing from the bottom of the ceiling board to the bottom of the mounting bar is 3/4 in. (4.1).
EXISTING CONSTRUCTION ASSEMBLY INSTRUCTIONS 10. Plug in LED panel (C) into the fan housing (A). 10 A C 11. Secure the LED panel (C) to the fan housing (A) using 4 short machine screws (BB) and metal washers (DD). 11 A Hardware Used BB Short machine screw x4 DD Metal washer x4 C DD BB 12. Choose which rim (D) finish suits your room. Lay glass globe (E) into chosen rim (D). 12 13. Line up the three notches around the outside of the LED panel (C) with the three clips on the rim (D).
CARE AND MAINTENANCE WARNING: Disconnect power supply before servicing. See SAFETY INFORMATION before proceeding. Routine maintenance should be done at least once a year. • Wash glass globe with mild soap and water, dry with a cloth. • Remove excess dirt and dust from the fan housing with a vacuum cleaner. • Do not use solvents, thinner or harsh chemicals for cleaning the fan. • Do not allow water to enter the motor. • Do not immerse resin parts in water over 140º F.