Installation Guide

2. Remove the screw on the battery compartment cover.
With your fingertip, pull up on the battery
compartment catch and pull outward to remove the
battery compartment cover.
PACKAGE CONTENTS
HARDWARE CONTENTS (shown actual size)
PREPARATION
ASSEMBLY INSTRUCTIONS
ASSEMBLY INSTRUCTIONS
Before beginning assembly of product, make sure all parts are present. Compare parts with
package contents list and hardware contents list. If any part is missing or damaged, do not
attempt to assemble the product.
Estimated Assembly Time: 45 minutes
Tools Required for Assembly (not included):
Phillips Screwdriver, Safety Glasses, Drill, 3/16 in. Drill Bit, Step Ladder, and Soft Cloth
CARE AND MAINTENANCE
ITEM #0784791
MODEL #SE1066-BP2-02LF0-U
LED MOTION-ACTIVATED
BATTERY OPERATED
SECURITY LIGHT
Français p. 7
Español p. 13
Anchors
Qty. 2
Wood Screws
Qty. 2
AA
ATTACH YOUR RECEIPT HERE
AB16126
Serial Number: Purchase Date:
3. Insert 3 new alkaline C cell batteries (not included)
into the battery compartment and orient them with the
“+” and “-” markings on the back of the battery
compartment. Re-attach the battery compartment
cover by aligning the legs on the lower edge of the
battery compartment cover onto the fixture body and
close the cover until the catch at the top engages.
Re-attach the screw. When ready to use, turn the
switch, located above the battery compartment, to
“ON”. There will be an approximate 15 second delay
for the fixture to light up, even if there is motion. This
will occur every time the fixture is turned “OFF” and
back “ON” at the switch or the batteries are changed.
Do not mix old and new batteries. Cold weather may
have a negative impact on battery life.
4. Attach the security light (A) to the mounting base (E)
by positioning the security light over the mounting base
at an angle. Engage the security light into the grooves
of the mounting base and secure by twisting clockwise
until the security light is seated vertically.
2. Remove the security light (A) from the mounting base
(E) by gripping the fixture and turning counterclockwise
until the catches disengage from the mounting base.
1. The red LED low battery indicator (C) on the front of
the security light will light up when the batteries are
low and need replacing. Alkaline batteries can last up
to 300 days if the security light is activated for 10
seconds an average of 4 times per night.
1. Remove the mounting base (E) by turning
counterclockwise until it comes loose. For mounting to
concrete or masonry, install the anchors (AA) by
drilling two 3/16-in. pilot holes into the mounting
surface. Insert the anchors (AA) into the holes and tap
them into place so they are flush with the surface.
Place the mounting base (E), with the writing facing
away from the wall, over the mounting location and
secure the mounting base to the mounting surface
with wood screws (BB).
A Security Light 1 D
E
Motion Sensor
Mounting Base
1
C Low Battery Indicator 1
1
PART DESCRIPTION QUANTITY PART DESCRIPTION QUANTITY
B Light Head 2
Qty. 2
Washers
CC
Wood
Screws
BB
x 2
Hardware Used
3
2
OPERATING INSTRUCTIONS
BATTERY REPLACEMENT
3
BB
C
B
A
SAFETY INFORMATION
WARNING
• LEDs can be damaged by electrostatic discharge (ESD) shock. Before installation, discharge
yourself by touching a grounded bare metal surface to remove this hazard. To avoid damage,
do not remove the clear lens over the LED module.
• This device complies with Part 15 of the FCC rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
Anchors
AA
x 2
Extreme hot or cold weather could affect the performance of the built-in sensors that detect body
heat. Certain winter clothing can shield a person’s body heat from the sensor during extreme cold
weather. During extreme hot weather, the sensor may not be able to distinguish the difference
between normal body temperatures and the surrounding high temperatures. The sensor will begin
working normally once weather conditions return to normal.
TROUBLESHOOTING
PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION
WARRANTY
Fixture doesn’t light.
Light flickers on and off.
Fixtures stays on all
night.
Motion sensor activates
at random or for no
reason.
Motion sensor does not
activate at all.
Detection range varies
from day to day.
1. ON/OFF switch is not set
correctly.
2. Batteries are defective.
3. Batteries are installed wrong.
4. Battery compartment cover
is loose.
1. Photo sensor is picking up
extraneous light.
1. Heat source/reflective body
in detection area.
1. Momentary heat source or
reflective body.
2. Minor sensor problem.
1. Batteries are depleted.
2. ON/OFF switch is set to OFF.
1. Changes in meteorological
conditions.
1. Slide ON/OFF position.
2. Replace the batteries.
3. Install the batteries correctly.
4. Check battery compartment cover.
1. Remove batteries to reset photo
sensor settings.
1. Remove heat source/reflective body
from detection zone or move fixture.
1. Turn sensor detection field away
from source.
2. Remove batteries to reset sensor.
1. Check or replace batteries.
2. Slide switch to ON position.
1. Adjust the position of the sensor.
The manufacturer warrants this lighting fixture to be free from defects in materials and workmanship for a
period of (2) years from the date of original purchase by the consumer. The fixture is not warrantied for
use in a commercial or retail application. The warranty is limited to use in a residential environment. We
will repair or replace (at our option) the unit in the original color, and style if available, or in a similar color
and style if the original item has been discontinued, without charge. Defective units must be properly
packed and returned to the manufacturer with a letter of explanation and your original purchase receipt
showing date of purchase. Call 1-866-994-4148 to obtain a Return Authorization Number and an address
where to ship your defective product. Note: C.O.D. shipments will NOT be accepted. The liability of the
manufacturer is in any case limited to replacement of the defective light fixture product. The manufacturer
will not be liable for any other loss, damage, labor costs or injury which is caused by the product. This
limitation upon the liability of the manufacturer includes any loss, damage, or injury which is (I) to person
or property or otherwise; (II) incidental or consequential in nature; (III) based upon theories of warranty,
contract, negligence, strict liability, tort, or otherwise; or (IV) directly, or indirectly related to the sale, use,
or repair of the product. This warranty gives you specific rights, and you may also have other rights which
vary from state to state.
Printed in China
Utilitech & UT Design® and Grounded in Quality® are
registered trademarks of LF, LLC. All Rights Reserved.
2. The motion sensor (D) can be rotated to position in the
direction of an area to be covered. If the 2 tick marks are
aligned, the motion sensor is focused straight ahead. The
motion sensor can be rotated approximately 45° right or
left of center. The motion sensor has a maximum
detection field of 130° at a distance of 30 ft.
3. The control knobs for adjusting the operation of the
security light (TIME, SENS and LUX) are located on the
back side of the motion sensor (D). To gain access to
these controls, rotate the sensor clockwise.
4. The LUX control knob can be adjusted for the
surrounding level of darkness needed to activate the
sensor. This is quite variable. The far left position (-) sets
for maximum level of darkness (or near full darkness).
The far right position (+) sets for minimum level of
darkness.
The SENS control knob can be adjusted to control the range of the sensor. The far left position (-) sets
the sensor range to approximately 1 ft. The far right (+) sets the sensor range to approximately 30 ft.
The TIME control knob can be adjusted to control the length of time the light stays ON when triggered
by the sensor. In the far left position (-), the duration time is approximately 10 seconds. In the far right
position (+), the duration time is approximately 30 seconds.
D
1
Periodically clean the fixture using a mild, non-abrasive glass cleaner and soft cloth. Do NOT use
solvents or cleaners containing abrasive agents. When cleaning the fixture, make sure the power is
turned off. Do not spray liquid cleaner directly onto the LEDs, fixture, diffuser, or wiring.
This fixture uses LEDs (light emitting diodes) to provide light. LEDs do not burn out like traditional
light bulbs and will last for 30 years or more (based on 3 hours of usage per day).
Utilitech & UT Design® and Grounded in Quality® are
registered trademarks of LF, LLC. All Rights Reserved.
Questions, problems, missing parts? Contact the customer service department at
1-866-994-4148, 8 a.m. - 6 p.m., EST, Monday - Thursday, 8 a.m. - 5 p.m., EST, Friday.
E
E
OPEN
OPEN
LOCK
LOCK
UPWARD
UPWARD
OFF ON
OFF
ON
2
OFF ON
OFF
ON
3. Install new batteries into the fixture by following the instructions detailed in Steps 2 - 4 in the
Assembly Instructions section.
AA
BB
3
OPEN LOCK
UPWARD
OPEN LOCK
UPWARD
5
4
1
OPERATING INSTRUCTIONS
1
1. The individual light heads (B) can be adjusted side to
side and up/down independently to aim the light heads in
the direction desired.
SENS
LUX
OFF ON
OFF
ON
C C C
SENS
TIM E L U X
2
1
4
B
A
D
D
OFF ON
OFF
ON
E
C
A
E
INSTRUCTIONS POUR L’ASSEMBLAGE
INSTRUCTIONS POUR L’ASSEMBLAGE
MODE D’EMPLOI
Lowes.com Lowes.com Lowes.com Lowes.com Lowes.com Lowes.com
21
3
4
5 6