SPOT-LITE CURING SYSTEM USERS GUIDE http://www.uvp.com UVP, Inc. 2066 W. 11th Street Upland, CA 91768 USA (800) 452-6788 or (909) 946-3197 Fax: (909) 946-3597 E-Mail: uvp@uvp.com Ultra-Violet Products Ltd. Unit 1, Trinity Hall Estate, Nuffield Road Cambridge, CB4 1TG, UK +44(0)1223-420022 Fax: +44(0)1223-420561 E-Mail: uvp@uvp.co.
Spot-Lite Users Guide Contents Contents Preface Introduction Components 2 .. 3 4 .. 5 Operation .. 6 Timer . 7 Lamp Replacement Specification Ordering Information 9 10 ..
Spot-Lite Users Guide Preface Copyright This manual is copyright UVP 1993. All rights reserved. No part of this manual can be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording, for any purpose, without the express permission of UVP. All information is correct at time of going to press. UVP reserves the right to change specifications without notice.
Spot-Lite Users Guide Introduction About this Guide This guide provides complete instructions to set up and run UVPs Spot-Lite system. The manual fully describes the components of the system, the methods for setting up the system including interconnections and adjustments, and a full description of how it can be used. If you have any problems installing or operating the equipment, please do not hesitate to call UVP at (800) 452-6788, (909) 946-3197 in the US or +44(0)1223-420022 in the UK.
Spot-Lite Users Guide Components Base Unit The base unit is available with a choice of two lamps 400w short wave (L1) or long wave (L2). Thanks to a unique light collection system (patent applied for) each Spot-Lite unit supports multiple wands. (Spot-Lite is available in a 2-outlet and 6-outlet version). The unit may be operated with as many wands fitted as required. When not in use, spare outlets are closed with an aluminum plug.
Spot-Lite Users Guide Operation Positioning Position the unit close to the area where the curing is to take place and in a position where any light discharge is away from the line of sight of the user. Ventilation should be allowed at the rear of the unit which should not be closer than 6 to any wall. Interconnections Mains lead this should be attached to the rear of the base unit in the socket located below the ON/ OFF switch.
Spot-Lite Users Guide Timer Timer settings are as follows: 99.99S 9999S 99.99 min 9999 min 99.99h 9999h 999.9S 99 min 595 999.9 min 99h 59 min 999.9h The curing time required can be set by adjusting the setting from 0 to 999 e.g. 999.1S = 99.9 seconds or 1.1m = 1/10 minute = 6 seconds To change the time on the timer, press any of 4 keys A corresponding to each digit. If the time rang needs to be altered e.g. from seconds to minutes.
Spot-Lite Users Guide Curing Once the unit is warmed up the timer has been set curing can commence. The end(s) of the wand(s) should be held or fixed close to the working area. For maximum cure speed, the tip of the wand should be within 5mm of the material to be cured. The Spot-Lite can now be activated by either pressing down the GREEN button located on the front panel or by depressing (and then releasing) the foot switch. The shutter will open and the time will commence its cycle.
Spot-Lite Users Guide Lamp Replacement If a lamp has ceased functioning, it should be replaced as follows: NB. Always ensure that the Spot-Lite has been isolated from the main voltage and that the unit is cool before proceeding with the replacement. Remove the outer casing by undoing the 8 counter sunk screws located adjacent to the handles. The lamp is housed within the aluminum shroud to the left of the unit. To gain access to the lamp: • • Remove all the screws from the forward aluminum cover.
Spot-Lite Users Guide Specifications Lamp: 400w short wave (L1) or long wave (L2) Light intensity L1 at 254nm 15mw/cm2 at 310nm 15mw/cm2 at 365nm 15mw/cm2 L2 at 254nm 1mw/cm2 at 310nm 4mw/cm2 at 365nm 15mw/cm2 measured at 50mm from tip of wand using UVPs UVX radiometer. Minimum spot size at 50mm is 50mm diameter Note: Closer to the tip of the wand all these intensities are significantly higher. Typically, at 365nm the intensity is in the order of 800-1000mw/cm2.
Spot-Lite Users Guide Ordering Information Spot-Lite Base Units (supplied without wands) Spot-Lite L1/2 base unit with L1 lamp and 2 wand sockets Spot-Lite L1/6 base unit with L1 lamp and 6 wand sockets Spot-Lite L2/2 base unit with L2 lamp and 2 wand sockets Spot-Lite L2/6 base unit with L2 lamp and 6 wand sockets Wands Available in 3 diameters: 3mm, 5mm, 8mm And 8 lengths: 0.5m 1.0m 1.2m 1.5m 1.8m 2.0m 2.5m 3.
