CONTENT SEK SERIES ELECTRONIC PIECE COUNTING / CHECK WEIGHING SCALE OPERATION MANUAL 1 2 3 4 5 6 7 8 CAUTION SPECIFICATIONS FEATURES KEYBOARD LAYOUT & FUNCTIONS DISPLAY INDICATORS INTERNAL FUNCTIONS TROUBLESHOOTING CALIBRATION READ THIS MANUAL BEFORE OPERATING THE SCALE *Specifications and functions subject to change without prior notice X0SEK030000 Revision: April 2008 Page: 1 2 3 4 5 7 8 14 15
Caution SPECIFICATIONS Before usage: a. Check and make sure that the input voltage of power b. c. Model No. Capacity (Max) Division (e) adaptor matches with the output voltage of the outlet. If it SEK-3000 3000g / 6.6lb 0.05g / 0.01oz does not, do not plug in the adaptor and contact your dealer SEK-6000 6000g / 13.2lb 0.1g / 0.01oz immediately. SEK-12K 12kg / 26.45lb 0.2g / 0.01oz Before first time use, plug the main adaptor into the wall SEK-30K 30kg / 66lb 0.5g / 0.
FEATURES KEYBOARD LAYOUT & FUNCTIONS Manual Zero Fuction (± 2% F.S.) Tare Function (Full Tare Available) Selectable Resolution and Weighing Units ( Resolution: 1/60,000, 1/30,000 or 1/15,000) (Weighing Units: g, lb, lb-oz, tael, or pcs) Low Battery Warning Indicator ( ) Backlight (Optional) Rear Display (Optional) RS-232 Interface (Optional) Press these keys to input desired numbers for settings (for Relay Output (Optional) example, setting the HI-OK-LO).
KEYBOARD LAYOUT & FUNCTIONS 4- TARE KEYBOARD LAYOUT & FUNCTIONS When inputting HI-OK-LO value or a load is placed on the scale, Press this key to tare off the weight of the load on the platter (full press and hold MODE/RANGE to set the displayed value as the tare available). range for HI and LO values from the OK value. The LED for HI and LO will light when the value is stored in the scale.
KEYBOARD LAYOUT & FUNCTIONS DISPLAY INDICATORS 10- HIGH LIMIT 13- CHARGE STATUS LIGHT When inputting the number using the numeric keypad or This LED light displays the charging status. When charging placing a load on the scale, press this key to set the HI limit for using the adaptor, the LED will turn red. The LED will turn HI-OK-LO (the LED for HI will light when the value is stored in green once the rechargeable battery is fully charged. the scale).
DISPLAY INDICATORS 19- LOW-BATTERY INDICATOR ***This sign appears when the battery is low. INTERNAL FUNCTIONS To access the internal functions: <1> Press and hold TARE, then press <2> Display will show “F0” 20- M+ INDICATOR <3> Press TARE until the desired Function is displayed An arrow on this sign indicates the accumulation function is in <4> Press MODE/RANGE to enter function use.
INTERNAL FUNCTIONS F9 INTERNAL FUNCTIONS Sound Alarm for HI-OK-LO (nobEEP, gobEEP, HLbEEP, HbEEP, LbEEP). (F4) Auto Power off Function a) Use the procedure described above to reach Function F4 F10 Relay Output Mode Selection (Act L – open / close, Act H open / close) b) Press MODE/RANGE. The display will show “XX_oFF” c) Press MODE/RANGE to select the Auto Power off time.
INTERNAL FUNCTIONS c) INTERNAL FUNCTIONS After Baud rate is selected, press MODE/RANGE, and the a) Use the procedure described above to reach Function F6. display will show “P=XXX”. Select Parity Setting by b) Press MODE/RANGE and display will show “FiLt_X” (X pressing SAMPLE. being the number selected from previously) P=n81 no Parity bit, data = 8 bit, stop bit = 1 bit c) P=E71 Even Parity bit, data = 7 bit, stop bit = 1 bit Press MODE/RANGE to select the Digital Filter number required.
INTERNAL FUNCTIONS (F8) Tare Mode Selection INTERNAL FUNCTIONS d) Press TARE to confirm, then press ON/ZERO to return to a) Use the procedure described above to reach Function F8. normal weighing mode. b) Press MODE/RANGE to enter, and display will show “X-tArE” (X being the previous selected mode) n_tArE S_tArE c) (F10) Relay Output Mode Selection Tare function can be used when weight is not a) Use the procedure described above to reach Function F10.
TROUBLESHOOTING Syndrome Scale cannot be turned on Scale turns off automatically after a period of time. Scale display shows symbol. Weight is not accurate. Possible Cause 1. Adaptor not plugged correctly. 2. Rechargeable battery has low battery. 3. Adaptor voltage incompatible with electrical outlet. Auto Power Off function is in operation. CALIBRATION Solution 1. Re-plug the adaptor to the scale. 2. Recharge the battery. 3. Replace the adaptor with the correct voltage.