User Manual TLT-1B GPS/GSM Vehicle Tracker （TLT-1B Tracker） V1.
Product main functions: 1. SMS inquires the real-time coordinates 2. Time to location, phone positioning 3. The initiative for help function 4. Speeding alarm function 5. Historical data upload function 6. Low electricity remind function 7. Movement track monitoring function Product main features Introduction The TLT-1B GPS/GSM Tracker is a vehicle remote positioning device with built-in GPS and GSM/GPRS technology in compact size.
� Can be used as a control command to change messages or switch GPS tracking � Can be pre-set three numbers, in an emergency, press the SOS button to take the initiative to call the stored telephone and send the exact location � The main technical index comply with equipment mobile phone international standard. GSM � Lightweight, compact, low power consumption � The support power cut oil power function and the broken oil recovery function.
Warm Start Average of 38 s Cold start Average of 42 s Height restriction Maximum 18,000 meters (60,000 feet). Speed limit The fastest 515 m / s (1000 section). Acceleration limit Less than 4g Operating Temperature -25℃ to 70℃ Humidity 5% ~ 95% non-coagulation Size 95mm*46mm*18mm Voltage 1300 mAh rechargeable battery (3.
RED LED—indicates power state: State Meaning Constant Lighting GSM out of work Flash every 8 Seconds GSM works well Green LED—indicate the GPS signal state： State Meaning Constant Lighting GPS not located Flash quickly GPS position located Charge status indication: Red light, said in charge of. Red micro-light, that is fully charged. Installation SIM card Open the PCB, have a SIM card slot. Then the card into the slot, until it completely, and ensure that it already embedded locked.
The external 4 wires of TLT-1BGPS/GSM tracker are as follows. Red for the 12V power wire, connect to the car battery anode; Black for the earth, connect to the car battery cathode; Yellow for the SOS for help Control wire, connect external SOS switch button to car battery cathode; Purple for cut-off oil and power control wire, connect to the relay coil 86, i.e. one end. Relay 85, i.e. anther end connects to oil and power supply 12V. 30, 87a are normal closed-end, series in the oil and power supply circuit.
2.10 SMS point to point mode: Command format: 700 + user password (4) For example: 7,000,000 Description: When TLT-1B receive the SMS, to confirm the user password is correct, the switch to SMS application mode. After the success of the sender to send the confirmation to the "SET MODE OK, CURRENT MODE: SMS P2P". 2.1.
Date: 2008-04-25 Time: 16:39:45 BS: 25ee0dff Fix: A ID: 353686009002030 STATE: SMS Invalid sample data： Lat: +22.50500 Long: +114.01000 Speed: 0.00KM/H Direction: 315.00 Date: 2008—04—25 Time: 16:39:45 BS: 25ee0dff Fix: V ID: 353686009002030 STATE: SMS Note: If the cold start and the GPS does not locate, then return invalid information as shown below.
2.1.2 Show Location on Map 1、Download Google Maps software from http://earth.google.com 2, start Google Maps software (for more information on the Google Maps software, please refer to http://earth.google.com) as shown above. (Note change in location data format) or you can copy http://maps.google.com in the Internet browser to connect Google Maps site shows location map. 3, send "666 + code" SMS command to the TLT-1B have latitude and longitude data.
Time: 16:39:45 BS: 25ee0dff Fix: A ID: 353686009002030 STATE: SMS Find locations in Google Maps, enter in the appropriate location: +22.50500 +114.01000. Obtain the following picture： 4、Or you can use the PDA or navigation device on a local map software, enter the location data.
3 Single positioning request instructions Product out of default mode in the SMS point to point, if you want to switch to GPRS mode, press the following command-line operation, GPSR online mode stored in the three phone numbers (1, 2, 3) and a 4-bit number of user passwords (and do not change as the first step), a group of TCP / IP server IP address and port number, 4 digit password and a GPRS GPRS access point APN number.
Instruction format 1: # 803 # user password # APN # # example: # 803 # 0000 # CMNET # # directive format 2: # 803 # Password # APN # APN Username Password # APN # # Note 1: different GSM / GPRS service providers to offer a different APN, please according to the local service provider's APN to choose to use the instruction format 1 or format 2 instruction set.
the user password is correct, send a confirmation to the sender short message: SET GPS SAMPLING TIME AND QUANTITY OK. Instructions specified in both the sampling interval T, a continuous reading GPS NEMA data in the $ GPRMC statement, and stored in memory. When the number of articles stored on the user to set up the Number of N per upload, began to connect GPRS server and the data sent.
4 SMS point to point mode, set projects and advanced applications 4.1.1 Change Password command Command format: 777 + new password 4 + Old Password 4 For example: 77712340000 Description: to confirm the old password is correct, update the user password for the new user password, set up after the success of confirmation to the sender to send a short message. Content for the "SET USER PASSWORD OK". 4.1.2 GPS status is set to command Send SMS commands make GPS work in open / close / adaptive three states.
1) Special power parameters Instruction format: 199 + user password + Xxx + Lyy + Hzz For example: 1990000S030L01H03 Description: S030 that off GPS 30 minutes, and can be set (1 255). Open the GPS that the first phase of L01 is 1 minute, can be set (1 ~ 98), the first stage if the second stage is not positioned directly off GPS; if not positioning the first stage, the second phase, H03 GPS represents the total time for the opening, that the second phase of 2 minutes (ie Hzz-Lyy), you can set (3 ~ 99).
(L01), if the GPS in the open for 1 minute (L01) localization, directly off GPS 30 min (S030). If a minute (L01) did not locate, will continue to open the GPS 2 min (H03-L01). 2 minutes regardless of whether the GPS positioning, all will be closed again for 30 minutes, again and again. Note: (1) switch to power saving mode GPS work, you must first set the command parameters 199.
GPS is in sleep mode at this time regularly uploading invalid and will not upload. 4.1.
Electronic fence is to set the coordinates for the center of the circle, set the radius to determine the scope of the fence. When turned on, set the fence after the TLT-1B beyond the scope of stored immediately after the No. 3 sent to a 3.1.1 format of location information. Information prompted the state to STATE: OS. Also call a telephone number stored in the first. If unsuccessful (shutdown or not connected), then in turn call the second, third.
Description: E - E; W - W; N - north latitude; S - south latitude. Used in this example is E and N, please select the appropriate location according to the actual coordinates of format settings. The meaning of the various parts of the sample as follows: Eddd.ddddd are degrees of longitude information, which ddd.ddddd that degree. (Decimal point behind the five, followed by zero can not be omitted) Ndd.ddddd is a degree of latitude in units of information, which dd.ddddd that degree.
the electronic fence to return to the sender to confirm the short message: GEO-FENCE ON. 3、Close E-fence: 210 + user password When the TLT-1B receiving the order to confirm the user password is correct closed electronic fence to return to the sender to confirm the short message: GEO-FENCE OFF. 2> set the rectangular range of the electronic fence Format: 006 + user password + GX, IO / I / O, E / W longitude limit + N / S latitude limit, E / W longitude limit + N / S latitude lower Eg:0060000G1,IO,E114.
Eg: 3100000G5 Description: This command is used to open all the electronic fence and open a single rectangular rectangular electronic fence, GX means that an electronic fence X, X range【1,16】 . When the device receives the instruction correctly recognized the user password to open the electronic fence sender rectangular return confirmation messages: Open all rectangular electronic fence resume SET ALL SQUARE GEO FENCE: OFF; open a single rectangular electronic fence is SET SQUARE GEO FENCE GX: OFF.
STATE: OVER SPEED. speeding alarm if it detects the speed of GPS in less than X, it indicates the speed at this time to return to a safe speed Under the driving, TLT-1B immediately sent to the No. 3 a 3.1.1 format stored location information, the information in the status prompt for the STATE: SAFE SPEED. 4.1.9 Historical data uploading In SMS mode, need to use this feature on the switch to GPRS mode on IP, APN settings, etc.
time to time under the same model as shown in 3.2.16, the information in the state prompted the STORAGE. B, to read all data records: Instruction Format: # 808 # 0000 # # Description: When the TLT-1B receiving the order to confirm the user password is correct, return to sender confirmation message: "START UPLOAD ALL HISTORY RECORD". Also sent to the server storage area began to record all the historical data, as shown in formats such as 3.2.16. Information in the state prompted the STORAGE. 4.1.
Description: When device receives instruction 1, and confirm the correct user password immediately after reading the GPS information, recognition information is valid, send the address information to send the number of Chinese. Such as: King East Road, Shenzhen, Guangdong Poly Garden East Gate south 339 degrees east within a distance of 31 meters. Send commands 2, will return a URL, open the URL you can see the current location and a current position of the shots, screenshots default size is 240 * 320.
http://maps.google.com/staticmap?center=22.554765,114.104716&zoom=16&size=240x240&ma ptype=mobile&markers=22.554765,114.104716,bluea&sensor=false&hl=cn 4.1.
control module (PIN58) output high level. After the completion of the users to send confirmation "POWER OFF OK". Broken oil electric single instruction format: 940 + user password Note: 940 = 9 + 901, module received stored number after the instructions from the immediate execution broken oil electricity, after the completion of the users to send confirmation "POWER OFF OK".
5 Automatic Update command 4.1.1 4.1.15 Command format:! - User password, FTP address, user name, password for example:! -0000, Igarin.gicp.net, 123, 0000 Description: When the device receiving the order to confirm the user password is correct, the automatic restart and automatically log on FTP address of the server download. When the update again after a successful reboot into normal use. Note: FTP address length 【5.35】, can also domain names, letters, numbers, dot (.) Underscore (_) and hyphen (-) form.
2, close the GPS commands Command format: 333 + User Password 4 For example: 3,330,000 Description: When the TLT-1B receiving the order, confirm the user password is correct, close the GPS, after the success of the sender to send the confirmation to the "GPS OFF OK".
confirmation message: GPS AUTO MODE: (yy-zz) / xxx Minutes. Note: (1) Set S / L / H and other parameters, if the high is 0, then we must make zero. For example: To turn off gps30 minutes will set the S030, but not set to S30. (2) Hzz opened GPS to set the total time, not less than Lyy. (3) 199 instruction set of the parameters are not lost restart, the reset will not change until reset.
(4) If you need real-time tracking, please use the GPS normally open mode. 5.1.3 Single positioning request instructions Command format: 666 + user password 4 Example: 6,660,000 Description: When the TLT-1B receiving the order, confirm the user password is correct, read the GPS information, regardless of the validity of the original software, set it with the base station with return return to the sender.
Lat: +22.50500 Long: +114.01000 Speed: 0.00KM/H Direction: 315.00 Date: 2008-04-25 Time: 16:39:45 BS: 25ee0dff Fix: V ID: 353686009002030 STATE: SMS Note: If the cold start and the GPS does not locate, then return invalid information Such as: ERROR GPS GPRMC FRAME DATA BS: 27971054 ID: 353686009002030 STATE: SMS 5.1.
5.1.6 From here instructions immediately Instruction Format: # 806 # user password # # Example: # 806 # 0000 # # Description: When TLT-1B receiving the order, confirm the user password is correct, the first stored number to send a confirmation SMS "START GPRS UPLOAD", sent to the server while the current store of data. From the data in the state prompted for the "SMS". Upload format： # IMEI number service password # user name # # status # data # Base Station Information $ GPRMC ... ... ..
message to the "SET VOICE CALL: ON ". 5.1.8 Phone Upload Description: When stored in one of three telephone calls come in to locate numbers, and 2-5 in the sound of ringing after the hang, then regarded as 3.2.16 command processing, the status prompt for the "CALL". 5.1.9 Emergency upload Description: When the regular press SOS button more than 3 seconds, then regarded as 5.1.6 command processing, the status prompt for the "SOS".
Edddmm.mmmm is divided into units of degrees longitude information, which said ddd degrees, mm.mmmm that sub. (Decimal point behind the four, followed by zero can not be omitted), Nddmm.mmmm is divided into units of degrees latitude information, which dd that degree, mm.mmmm said points. (Decimal point behind the four, followed by zero can not be omitted) zzz.z is the domain of radius 【999.9 - 0.1】, in units of KM.
to send reminder: ERROR GPS DATA, TRY AGAIN LATER. After the GPS set to resume their original state (on / off / adaptive). Note: 1, fences can not exceed the radius of its domain, the fractional part of the right to a value of zero must enter zeros. For example: R = 1, must be entered as 1.0. 2, if the calling state is off, it will not make calls, send text messages to pre-existing users only. 3 degrees and is divided into 60 binary conversion, that 1d = 60m.
(3) The setting of this directive, and the switch from power-down effect of changes until you receive further instructions or reset operation. (4) After reset, the value of latitude and longitude marked with 0. Fence is turned off. 2.
the speed alarm function, X =! 0 speed alarm function is turned on, after the success of the first stored to send confirmation information "SET RATE LIMIT: X. When the speed alarm function is turned on, TLT-1B began to read the speed of GPS data and comparison with X real-time. If the GPS speed is greater than in X, the instructions at this time for speeding, TLT-1B a 3.2.16 immediately sent to the server location information formats, information in the state prompted the OVER SPEED.
A, From 24-hour history: Instruction Format: # 808 # user password # 24 # # Example: # 808 # 0000 # 24 # # Note: When receiving the order confirmation TLT-1B user password is correct, return to sender confirmation message: "START UPLOAD 24H HISTORY RECORD". Sent to the server while starting the last 24 hours recorded in historical data, format and GPRS From time to time under the same model as shown in 3.2.16, the information in the state prompted the STORAGE.
for example: 6670000 Instruction format 2:667 + user password + MAP example: 6670000MAP Instruction format 3:667 + user password + MAP, WWW, HHH, ZZ Example: 6670000MAP, 640,480,15 Description: When device receives instruction 1, and confirm the correct user password immediately after reading the GPS information, recognition information is valid, send the address information to send the number of Chinese.
(Note: WWW, HHH these two values can not be greater than 1000, ZZ between the values proposed 1-20) when the device receives the command, make sure the correct user password immediately after reading the GPS information, recognition information valid, send the current location of the Google Maps screenshot of the website, you set the capture resolution of the resolution. Screenshots URL example: http://maps.google.com/staticmap?center=22.554765,114.104716&zoom=16&size=240x240&ma ptype=mobile&markers=22.
according to the value of X is upload invalid data set switch state. X = 1, open invalid data upload. After the success confirmation to send the short message: INVALID DATA UPLOAD: ON, at this time whether TLT-1B GPS data received is valid will be uploaded to the server. X = 0, close the upload invalid data, set after the success of the short to send the confirmation message: INVALID DATA UPLOAD: OFF, then close the invalid data upload, only upload valid data.
passwords is correct, the stored number to send confirmation information: "" Power OFF?" Then preparing to receive user confirmation instructions. If the received within 10 minutes of user send confirmation instructions, then cut gas and electric control module (PIN58) output high level. After the completion of the users to send confirmation "POWER OFF OK".
6 Accessibility 1, the command reset * RESET # 0000 # #. Description: This command resets all the configuration information after the restart to the factory configuration. 2, the instruction restart * RESTART # 0000 # # Description: This command only restart the TLT-1B, do not reset the configuration information. 3, the current configuration of the module to read SMS command format: * GTAS # Function: When the module receives instructions, return all the settings stored in the module.
U3: No. 3, password SC: Service Center number, service code 6.2 The state labeled Status 666 single request Corresponding identity 4XX regularly sent SMS TIMER Phone Location CALL Answer ANSWER Seek help SOS DEF Power failure alarm alarm A fence OS Finalists selected RS Speed alarm OVERSPEED Safe speed SAFESPEED Historical Data Upload STORAGE Low voltage alarm LP 806 single-hair positioning SMS From time to time to go car AUTO track From time to time stop AUTOLOW throttling 6.
Power failure alarm Off (disarm) Electronic fence Close Calling switch Open Service center number Air GPRS Password 0000 GPRS name V500 IP Address 0.0.0.0 0000 Shift alarm Open (non-off petrol and electricity) Speed alarm Stop Parking throttle upload Stop Close Go cart track upload Close ANP CMNET Calling switch Open Off petrol electricity Historical data sampling Stop Historical Upload ACC switch state tips Open Upload data and Data invalid 6.
Instruction Explain 700+ Password 710+ Password 003 Password E/Wxxxx.xxxxN/Syyyy.yyyyRzzz.z 004+ Password E/Waaa.aaaaaN/Sbb.bbbbbRzzz.z 005+ Password Rzzz.
Instruction Explain 700+ Password 710+ Password 003 Password E/Wxxxx.xxxxN/Syyyy.yyyyRzzz.z 004+ Password E/Waaa.aaaaaN/Sbb.bbbbbRzzz.z 005+ Password Rzzz.
