Installation Guide

ManualsBrandsV-Zug ManualsCooking AppliancesV-ZUG 90cm Natural Gas Cooktop GAS951GSBZ

Installation instructions

Built-in variants of gas hob

Multi-sliders GAS411/421/641/951

1014422-R09

27/07/2017

1014422-R09

The appliance must be installed by qualified personnel only. Each step must be carried out and checked in full in the

order specified.

Check that the local connection conditions (gas type and gas pressure) and the appliance setting match before con-

necting the appliance.

The default values for this appliance are provided on the information plate (or on the identification plate).

This appliance is not connected to a combustion by-product outlet. It must be set up and connected according to the

applicable installation conditions. Particular attention must be paid to the relevant ventilation requirements.

If installing into a combustible material, the guidelines and standards for low voltage installations and fire protection

must be strictly observed.

Validity

These installation instructions apply to the following models:

Product family Type Appliance class

31063 GAS411GSBZ Class 3

DIN EN 30-1-1

31064 GAS421GSBZ

31071 GAS641GSBZ

31072 GAS951GSBZ

General notes

Identification plate

The identification plate and stickers with the permissible

gas types and safety precautions are located on the under-

side of the hob.

Identiﬁcation plate

Depending on

appliance, plate

with additional

information

▸ Affix the second identification plate (supplied) in an accessible position behind the front of the fitted cabinet beneath the appliance.

Care and maintenance

▸ Follow the care and cleaning advice in the operating instructions.

▸ Follow the basic maintenance advice in the operating instructions.

Summary of content (9 pages)

PAGE 1
014422-R09 Installation instructions 27/07/2017 Built-in variants of gas hob Multi-sliders GAS411/421/641/951 1014422-R09 The appliance must be installed by qualified personnel only. Each step must be carried out and checked in full in the order specified. Check that the local connection conditions (gas type and gas pressure) and the appliance setting match before connecting the appliance. The default values for this appliance are provided on the information plate (or on the identification plate).
PAGE 2
1014422-R09 Installation instructions 27/07/2017 Built-in variants of gas hob Multi-sliders GAS411/421/641/951 1014422-R09 Installation accessories provided For all installation variants: Designation Art. no. 4 adjusting braces H61561 Sealing ring gas connection 18 × 13 × 1.5 mm H64006 Flush installation: Designation Art. no. Cementing-in instructions J004133 Sealing strip set H63283 Spacer set H60330 Accessories Surface-mounted installation: Designation Article no.
PAGE 3
1014422-R09 Installation instructions 27/07/2017 Built-in variants of gas hob Multi-sliders GAS411/421/641/951 1014422-R09 Surface-mounted installation The cooking zone layout of the hob to be fitted may differ from the hob illustrated! GAS411GSBZ, GAS421GSBZ GAS641GSBZ Ri 384 Y H Y 1 1 50 0 ≥5 0 ≥5 373± 1 1 S* ≥81 A 60 0 ≥400 1 Ra Ra 0 ≥5 60 0 60 600 Y–Y 900 2 A 0 60 0 49 886± 1 0 ± ≥5 90 4 560± ±1 49 1 50 0 A 0 Ra ≥5 0 Y Y 50 ≥5 897 B H Y 1 0± Ri 571 Y H
PAGE 4
1014422-R09 Installation instructions 27/07/2017 Built-in variants of gas hob Multi-sliders GAS411/421/641/951 1014422-R09 Flush installation The cooking zone layout of the hob to be fitted may differ from the hob illustrated! GAS411GSBZ, GAS421GSBZ 384 Ri GAS641GSBZ Ri 571 Y 5 577± 5 1. 1 ≥4 07± 5 0 60 ≥4 S* ≥85 1 ≥4 Z 5 1. ≥4 0 60 600 A 1 50 8.5 Y–Y ≥4 5 1. 1 903± 7± 1 50 5 Z 1. 60 0 Detail Z Ra 0 -1 900 2 A Z 5 1.
PAGE 5
1014422-R09 Installation instructions 27/07/2017 Built-in variants of gas hob Multi-sliders GAS411/421/641/951 1014422-R09 ▸ Connect to the electrical mains connection before inserting the appliance, if necessary. Combination installation Flush combination installation is described in document 1014381. The intermediate support kit H63789 is required for this.
PAGE 6
1014422-R09 Installation instructions 27/07/2017 Built-in variants of gas hob Multi-sliders GAS411/421/641/951 1014422-R09 Minimum distances and installation conditions The distance from the appliance cut-out to the back wall must be ≥50 mm and to the side walls ≥200 mm. Parts such as side walls and reinforcing strips which protrude into the installation space under the cooking zone must be made of fire-resistant material.
PAGE 7
1014422-R09 Installation instructions 27/07/2017 Built-in variants of gas hob Multi-sliders GAS411/421/641/951 1014422-R09 ▸ The gas connection must be positioned so that the stop-cock and the supply connection point are accessible with the appliance installed. ▸ The gas connection must be positioned so that it does not get detrimentally hot during operation. In particular, the gas hose assemblies and the appliance’s connection fittings must be clear of hot exhaust gases (e.g. from an oven).
PAGE 8
1014422-R09 Installation instructions 27/07/2017 Built-in variants of gas hob Multi-sliders GAS411/421/641/951 1014422-R09 Changes to the service menu Changes to the service menu can only be made within 1 minute of applying the voltage. If the appliance has already been connected for a longer period, interrupt the power supply for about 10 seconds. ▸ With the hob switched off, hold the and buttons depressed at the same time for 4 seconds. – An acoustic signal is emitted.
PAGE 9
1014422-R09 Installation instructions 27/07/2017 Built-in variants of gas hob Multi-sliders GAS411/421/641/951 1014422-R09 GAS641 ... 1 2 GAS951 ... 3 Type GAS641 … 4 1 Slider 1 Slider 2 Gas configuration - GAS951 … 2 Slider 3 Gas configuration 3 4 5 Slider 4 Slider 5 - - - - Conversion to another gas type The appliance is set up for a certain gas type, which is also recorded on the identification plate.