Installation Guide

ManualsBrandsV-Zug ManualsCooking Appliances90cm Downdraft System

Installation instructions

Range hood

Mode: Extraction / Recirculation

DSTS9

1011458-R02

15/03/2016

The appliance should be installed by qualified personnel only.

Each step must be carried out and checked in full in the order specified.

Validity

64004 (DSTS9, construction width 90 cm)

General notes

Identification plate

▸ Remove the grease filters. The identification plate is located on the inside of the appliance.

Installation accessories supplied

All fixing elements are contained in the scope of delivery.

Mains cable 12 self-tapping screws 3.5 × 9.5mm

Lower angle bracket 6 screws M4 × 8mm

Upper angle bracket 6 screws 4 × 15mm

Angle brackets

(are not used)

Accessories: Recirculation box

Extraction mode

The extracted air must not be fed into a chimney which is used for exhausting fumes from appliances burn-

ing gas or other fuels.

Observe the local fire regulations.

Recirculation mode

The air outlet grille must not be covered during operation.

Summary of content (9 pages)

PAGE 1
Installation instructions 1011458-R02 Range hood Mode: Extraction / Recirculation DSTS9 15/03/2016 The appliance should be installed by qualified personnel only. Each step must be carried out and checked in full in the order specified. Validity 64004 (DSTS9, construction width 90 cm) General notes Identification plate ▸ Remove the grease filters. The identification plate is located on the inside of the appliance.
PAGE 2
Installation instructions 1011458-R02 Range hood Mode: Extraction / Recirculation DSTS9 15/03/2016 Dimensions Cannot be installed in conjunction with a gas hob. Flush installation variant 7 Recessed installation variant 0 108 12 88 0 4 R0–5 R5 124 4 812 884 76 5 6 11 80 2 0 25 400 65 4 2 2 1 4 7 2,4 33 8 10 646 332 98 12 R0–5 2 10 88 81 4 2 R5 4 166 12 8 81 2 10-200 17 -1 10 8 8 10 (ø150) 30 ≥660 0 ≥3 R0 –5 3 1 The fan can be rotated for mounting.
PAGE 3
Installation instructions 1011458-R02 Range hood Mode: Extraction / Recirculation DSTS9 15/03/2016 Installation ▸ ▸ Carefully insert the hood body 1 in the prepared cut-out 2 (see Dimensions). 1 For flush installation, level the hood body at the right height (using spacer set H6.0330). 2 ▸ Fasten the lower brackets 3 to the housing 5 of hood body 1 using two screws 4 for each bracket so that the feet 6 rest on the base of the cabinet. 1 The brackets can also be rotated for mounting.
PAGE 4
Installation instructions 1011458-R02 Range hood Mode: Extraction / Recirculation DSTS9 15/03/2016 ▸ 1 Loosely fasten the upper brackets 7 to the housing 5 of the hood body 1. The brackets can be adjusted. Push the brackets 7 up and fasten in place under the worktop 8 using screws 24. ▸ Tighten screws 9 on the housing 5. Alternatively, the brackets can also be rotated for mounting so that the hood body can be fastened to the side of the cabinet.
PAGE 5
Installation instructions 1011458-R02 Range hood Mode: Extraction / Recirculation DSTS9 15/03/2016 ▸ Run the connecting cable 11 from the hood body 1 to the motor housing 12 and plug it into the fan 13. ▸ Lay the cable 11 and fitted with the cable bushing 14 supplied insert into the cable receptacle in the housing 5. 1 14 13 12 11 Alternatively, the motor housing 12 can be mounted to the hood body from the back. 13 To do this, remove the back cover 21 from the housing 5 and mount at the front.
PAGE 6
Installation instructions 1011458-R02 Range hood Mode: Extraction / Recirculation DSTS9 15/03/2016 ▸ Turn the motor housing 13 so that the exhaust connection 15 points in the desired direction and fasten it to the housing 5. 5 4× M4×8 mm 13 15 4× 3,5×9,5 mm ▸ Insert the three connecting cables 16, which exit the housing from the underside of the range hood 5, into the corresponding couplings 17 on the underside of the control unit 18. 5 Make sure that the connectors engage firmly.
PAGE 7
Installation instructions 1011458-R02 Range hood Mode: Extraction / Recirculation DSTS9 15/03/2016 Moisture ingress in the cabinet could lead to a risk of electric shock. The connection box must, therefore, have no contact with the floor. The cable must be laid and secured in a suitable place. ▸ Insert the mains cable 19 supplied into the socket 20 on the underside of the control unit 18. 18 19 20 ▸ Fasten the control unit 18 to the range hood using screws.
PAGE 8
Installation instructions 1011458-R02 Range hood Mode: Extraction / Recirculation DSTS9 15/03/2016 For flush installation: Use cementing-in set for flush installation, art. no. 86392885. ▸ ▸ Raise the range hood. Apply sealant and allow sealant joints to dry completely. Extraction mode There is a danger of toxic fumes developing if the range hood is operated at the same time as an ambient air-dependent firing system! ▸ Fasten exhaust ducting 22 to exhaust connection 23.
PAGE 9
Installation instructions 1011458-R02 Range hood Mode: Extraction / Recirculation DSTS9 15/03/2016 – Only use elbows with large radii. – The exhaust ducting must not be kinked or compressed. – Make sure that all connections are secure and airtight. Any constriction of the airflow will reduce extraction performance and increase operating noise. ▪ If the exhaust duct is to be routed outdoors, we recommend installing a telescopic wall box or a rooftop vent (accessory available for purchase).