Wet/Dry Vacuum Operator’s Manual 14 Gallon Model No. VJE1412SW 0201 FOR YOUR SAFETY Read and understand this manual before use. Keep this manual for future reference. Distributed By Cleva North America, Inc. 601 Regent Park Court Greenville, SC 29607 Replacement Filters & Accessories available at: Vacmaster.
TABLE OF CONTENTS SECTION PAGE Warranty........................................................................................................................................... 2 Safety Instructions & Warnings........................................................................................................ 3 Double Insulation Instructions.......................................................................................................... 4 Extension Cords......................................
SAFETY INSTRUCTIONS & WARNINGS IMPORTANT SAFETY INSTRUCTIONS READ AND UNDERSTAND ALL INSTRUCTIONS BEFORE USING THIS VACUUM. Read and understand this operator's manual and all labels on the Wet/Dry Vacuum cleaner before operating. Safety is a combination of common sense, staying alert, and knowing how your vacuum works. Use this Wet/Dry Vac only as described in this manual. To reduce the risk of personal injury or damage to your Wet/Dry Vac, use only Vacmaster ® recommended accessories.
DOUBLE INSULATION INSTRUCTIONS This Wet/Dry Vac is double-insulated, eliminating the need for a separate grounding system. Use only identical replacement parts. Read the instructions for Servicing Double-Insulated Wet/Dry Vacs before servicing. Use this Wet/Dry Vac as described in this manual. Observe the following warnings that appear on the motor housing of your Wet/Dry Vac. DOUBLE INSULATED - GROUNDING NOT REQUIRED - WHEN SERVICING USE ONLY IDENTICAL REPLACEMENT PARTS.
UNPACKING & CHECKING CARTON CONTENTS A Remove all contents from the box. Remove the power head and take out any contents inside the collection tank. Check each item against the carton contents list. B Carton Contents List: C D E F I J N S O G K P T H L Q M R Key Description......................................... Qty. Vac Assembly......................................... 1 A Hose ...................................................... 1 B Extension Wands................................
GENERAL ASSEMBLY INSTRUCTIONS A Philips head screwdriver driver is required. 2 1 6 3 4 7 8 10 9 12 13 5 11 14 1 2 WARNING: DO NOT PLUG POWER CORD INTO POWER OUTLET. MAKE SURE PLUG IS DISCONNECTED BEFORE ASSEMBLING THE WET/DRY VACUUM. 1. 2. 3. 4. 5. 6. 7. 8. 9. Verify that the power cord is disconnected from the outlet. (Fig. 1) Undo the latches. (Fig. 2) Lift the power head off the collection tank. (Fig.
10. For wet vacuum cleaning, install the supplied foam wet filter. For filter installation instructions see page 12. (Fig. 10) 11. Place the power head back on the collection tank aligning the top section with the latches, and snap into place. (Fig. 11 & 12) 12. Insert the locking end of the hose into the vacuum port and turn to lock into place. (Fig. 13) 13. Fit the required accessory onto the suction tube. (Fig. 14) Note that a static discharge chain is attached to the bottom of the tank.
1. Verify that the power cord is disconnected from the outlet. (Fig. 1) 2. In order to prepare your vacuum for dry vacuuming, verify that the cartridge filter is securely mounted. With the power head removed and in an upside down position, make sure the filter is pushed in until it stops against the power head and the retainer is installed. Your wet/dry vac comes with the cartridge filter pre-installed. For installation instructions see page 11. (Fig. 2) 3.
1. Verify that the power cord is disconnected from the power outlet. Ensure that the tank is clean and free of dust and dirt. (Fig. 1) 2. Remove the cartridge filter and install the foam wet filter over the filter cage and place the power head back on the collection tank. For filter installation instructions see page 13. (Fig. 2) DO NOT USE THE CARTRIDGE FILTER FOR LIQUID VACUUMING. OPERATING INSTRUCTIONS: WET VACUUMING 3. Fit the desired nozzle to the vacuum hose. (Fig. 3) 4.
6. Verify that the power switch is in the ‘O’ OFF position before plugging the power cord into the outlet. (Fig. 4 & 5) 7. Before turning ON the vac, firmly hold the loose end of the hose. Turn the motor on by pressing the switch to the ‘I’ ON position. (Fig. 6) 8. Once you have completed blowing, flip the power switch to the 'O' (OFF) position and unplug the power cord from the outlet. (Fig. 7) MAINTENANCE Emptying the Collection Tank 1 1. 2. 3. 4. 5. 6. 7.
INSTALLING & CLEANING CARTRIDGE FILTER 1 2 3 4 5 6 Installing Cartridge Filter 1. Verify that the power cord is disconnected from the outlet. (Fig. 1) 2. Remove power head and place in upside down position. 3. Install the cartridge filter over the filter cage with the flat end of the filter towards the power head. Carefully push filter in until it stops against the power head. (Fig. 2 & 3) 4.
INSTALLING & CLEANING FOAM WET FILTER 1 2 3 4 5 Installing Foam Wet Filter 1. Verify that the power cord is disconnected from the outlet. (Fig. 1) 2. Remove power head and place in upside down position. Follow instructions to remove cartridge filter. 3. Carefully slide foam wet filter down over the filter cage making sure the cage is completely covered. (Fig. 2 & 3) 4. Place the power head onto the collection tank. Cleaning Foam Wet Filter 1.
EXPLODED VIEW 1 21 15.1 2 15 2 15.
PARTS LIST Part 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 15.