Wet/Dry Vacuums Operator’s Manual 6 Gallon Model No. VQ607SFD FOR YOUR SAFETY Read and understand this manual before use Keep this manual for future reference www.vacmaster.
TABLE OF CONTENTS SECTION PAGE Warranty…………………………………………………………………………………………...……. Safety Instructions and Warnings……………………………………………………………………. Double Insulation Instructions…..……………………………………………………………………. Extension Cord…………………………………………………………………………………………. Unpacking and Checking Carton Contents………….……………………..…………….…………. General Assembly Instructions…………………………………………………………….…………. Dry Vacuum Operation………………………………………………………………………………… Wet Vacuum Operation………………………………………………………………………………..
SAFETY INSTRUCTIONS & WARNINGS IMPORTANT SAFETY INSTRUCTIONS READ AND UNDERSTAND ALL INSTRUCTIONS BEFORE USING THIS VACUUM Read and understand this owner’s manual and all labels on the Wet/Dry Vacuum cleaner before operating. Safety is a combination of common sense, staying alert and knowing how your vacuum works. Use this Wet/Dry Vac only as described in this manual. To reduce the risk of personal injury or damage to your Wet/Dry Vac, use only Vacmaster® recommended accessories.
DOUBLE INSULATION INSTRUCTIONS This Wet/Dry Vac is double-insulated, eliminating the need for a separate grounding system. Use only identical replacements parts. Read the instructions for Servicing Double-Insulated Wet/Dry Vacs before servicing. Use this Wet/Dry Vac as described in this manual. Observe the following warnings that appear on the motor housing of your Wet/Dry Vac. DOUBLE INSULATED - GROUNDING NOT REQUIRED - WHEN SERVICING USE ONLY IDENTICAL REPLACEMENT PARTS.
UNPACKING AND CHECKING CARTON CONTENTS Remove entire contents from carton. Check each item against the contents list. Contents List Key Description……………………..…….…QTY A B C D E F G H I J K L M N O Vac Assembly……………………………..1 Hose With Air Control Nozzle…..............1 Extension Wands..…………………….....2 2-in-1 Utility Nozzle…………………….....1 Crevice Tool……………………………… 1 Multi-Surface Floor Nozzle....….………..1 Round Dust Brush..................................1 Cartridge Filter…………………….……...
GENERAL ASSEMBLY INSTRUCTIONS A Philips head screw driver is required for assembly. WARNING: DO NOT PLUG IN POWER CORD TO POWER OUTLET, MAKE SURE PLUG IS DISCONNECTED BEFORE ASSEMBLING THE WET/DRY VAC UNPACKING YOUR WET/DRY VACUUM & GENERAL ASSEMBLY 1. Verify that the power cord is disconnected from the outlet. (fig.1) 2. Undo the latches. (fig.2) 3. Lift the power head off the container. (fig.3) 4. Remove the contents from inside the container, make sure you have all contents as listed on page 5. (fig.
POLARIZED PLUG To reduce the risk of electrical shock, this appliance has a double polarized plug (one with the blade wider than the other). This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper outlet. Do not change the plug in any way. Double insulation eliminates the need for the three wire grounded power cord and grounded power supply system.
5. Insert the locking end of the hose into the vacuum port and screw in place. Push the required attachment onto the free end of the hose or extension. (fig.6) 6. Plug in the power cord into the outlet. (fig.7) 7. Turn the motor on by flipping the switch to the ‘I’ ON position. (fig.8) 8. Once you have completed vacuuming, flip the switch to the ‘O’ OFF position and unplug the power cord from the outlet.
in motor speed. When this happens, turn off the machine, disconnect from power supply, and drain the liquid into a suitable receptacle or drain. To continue vacuuming, refit the container with the drain cap. After wet vacuuming, turn the machine off and remove plug from power supply. Empty the container, clean and dry the inside and outside before storage. REMEMBER! The foam filter must be removed after wet vacuuming, and a cartridge filter must be installed before dry vacuuming again.
MAINTENANCE WARNING: DO NOT PLUG IN POWER CORD TO POWER OUTLET. MAKE SURE PLUG IS DISCONNECTED BEFORE CHANGING AND CLEANING FILTERS. 1. Verify that the power cord is disconnected from the outlet. (fig.1) 2. Disconnect the hose from the vacuum, turning large end in counter clockwise direction. (fig.2) 3. Undo the latches and remove the power head from the container. (fig.3) 4. Clear all dirt or debris from the container and hose. (fig.4) 5.
3. Clean the cartridge filter by gently tapping or brushing dirt off. Cleaning should not be done indoors in living areas. For optimal performance a new filter is recommended. 4. Install cleaned or new filter into place as instructed above in steps 2 and 3 of Installing Cartridge Filter. 5. Wet filters should be removed and allowed to air dry for 24 hours before installing onto the filter cage. INSTALLING & CLEANING FOAM SLEEVE FILTER Installing Foam Sleeve Filter 1.
PARTS LIST - EXPLODED VIEW 12
