Use & Care Guide 21.6V 2-IN-1 CORDLESS VACUUM MODEL NO. VSG2101 www.vacmaster.com Cleva North America, Inc.
TABLE OF CONTENTS SECTION PAGE Important Safety Instructions................................................................................................................3-5 Warranty…………....................................................................................................................................6 Technical Data........................................................................................................................................6 Getting To Know Your Vacuum.........
IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance, basic precautions should always be followed, including the following: READ ALL INSTRUCTIONS BEFORE USING THIS VACUUM CLEANER. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. WARNING - To reduce the risk of fire, electric shock, or injury: • Do not use outdoors or on wet surfaces. • Do not allow to be used as a toy.
• Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack. • Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact accidentally occurs, flush affected area with water. If liquid contacts eyes, additionally seek medical help. Liquid ejected from the battery may cause irritation or burns.
WARNING Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
WARRANTY FOR ONE YEAR from the date of sale, this product is warranted against defects in material or workmanship when it is assembled, operated and maintained according to all supplied instructions. WITH PROOF OF SALE, a defective appliance will be replaced free of charge. For warranty coverage details to obtain free replacement, visit the web page: www.vacmaster.com or call (866) 384-8432.
GETTING TO KNOW YOUR VACUUM Handle LED Indicators (2) On/Off Button Charging Port Dust Cup Release Button Dust Cup Wand Release Button Dust Release Latch Wand Nozzle Release Button Motorized Nozzle Charging Adapter Crevice Tool 2-in-1 Wall Mounting Combination Tool Bracket REPLACEMENT PARTS Item Filter (2) Brush Roll Charging Adapter Wall Mounting Bracket Screw (2) Crevice Tool 2-in-1 Combination Tool Part No.
GENERAL ASSEMBLY INSTRUCTIONS Assembly Instructions 1. Align and insert the top of the wand into the hand vacuum until you hear a click. Note: Make sure it fits firmly. To remove the wand, press the wand release button and separate. 2. Insert the motorized nozzle into the bottom of wand until you hear a click. 3. Mount the wall mounting bracket on the wall. Do not secure the bracket to drywall only. Secure the screws to a stud. Use the 2 screws provided.
59” (Recommended) 44” (Minimum) 4. To store, hang the hand vacuum on the wall mount. Align the slot on the bottom of the hand vacuum with the protrusion on the wall mount as shown in the picture below. 5. Insert the 2-in-1 combination tool into the right slot on top of the wall mounting bracket for convenient storage. Insert the crevice tool into the left slot.
Charging Instructions 1. Before charging, make sure the cordless vacuum is turned OFF. Insert the charging connector into the charging port of the hand vacuum. Then insert the charging plug into a wall outlet. 2. The LED indicators will show the progress of the charge. While the vacuum is being charged, the LED indicators will be flashing blue alternately. Once fully charged, the LED indicators will show static blue lights. The battery requires approximately 4~5 hours of charging to regain full capacity.
OPERATING INSTRUCTIONS CAUTION Operate appliance at room temperature between 39.2°F (4°C) and 104°F (40°C) in order to ensure its safety and normal function. Using Your Vacuum Cleaner Note: When vacuum cleaner is fully charged, unplug the charging adapter. Make sure the vacuum cleaner is completely assembled and the dust cup is empty before using. Do not operate vacuum cleaner without filters in place. This vacuum provides two-speed control.
2. To switch the speed to LOW, press the on/off button again. The LED indicators will indicate the LOW speed with one LED illuminated. 3. To stop the vacuum, press and hold the on/off button for 1 second for a third time. Note: • You will know the battery needs charging once the LED indicators change from blue to red. • For best performance, empty the dust container once dust reaches the "MAX" level marked on the dust cup while vacuuming. Follow instructions on page 13.
2. Insert the motorized nozzle or accessory tools into the end of the hand vacuum until you hear a click. 3. When finished cleaning, turn the vacuum cleaner off and press the wand release button to remove the motorized nozzle or accessory tools. MAINTAINING YOUR VACUUM CAUTION To reduce the risk of shock, remove vacuum cleaner from the charging adapter, and turn off before performing any service or maintenance.
1. Position dust cup area of vacuum over a waste receptacle. Press down on the dust release latch to open dust cup lid and allow contents to drop into waste receptacle. Dust Release Latch 2. If necessary, clean off hair and other debris wrapped around the pre-filter. After repeated use, it is necessary to wash the non-woven filter and the foam filter clean of accumulated dust. Cleaning the Filters 1. Press the dust cup release button to separate the dust cup from the hand vacuum.
2. To separate the top from the dust cup, hold the top of the dust cup and rotate counterclockwise. Then lift the top and filter from the dust cup. Chamber Pre-filter Foam Filter Non-woven Filter 3. Brush loose debris from filters then rinse with warm water. Rinse and gently squeeze dry the foam filter. Set both filters aside and allow to air dry for 24 hours. IMPORTANT: The filters must dry completely before reuse. 4. There may be debris wrapped around the pre-filter.
5. Place the filters back onto the pre-filter. With the dust cup release button facing away from the wand connection on the dust cup, lock the top into place by rotating clockwise. 6. To reassemble the dust cup to the hand vacuum, align the slot in the dust cup to the hand vacuum. Once aligned, press down on the dust cup release button until you hear a click.
Cleaning the Motorized Nozzle & Blockages The brush roll may accumulate debris such as strings, hair and fibers. This type of debris can wrap around the brush and diminish its ability to clean effectively. To Remove Brush Roll for Manual Cleaning: 1. Make sure the vacuum cleaner is turned off. Remove the wand and the hand vacuum from the motorized nozzle and set aside. 2. Turn the nozzle over to access the brush roll. As shown below, push the tab on the left hand side of the nozzle to the left.
TROUBLESHOOTING Hose Blockage Removal 1. To clean out the hose, press the release button on the wand and separate the nozzle from the wand. 2. Carefully remove any debris or blockage from the inside of the nozzle neck. 3. Once the blockage is removed, reattach the wand and hand vacuum to the nozzle. Start the vacuum to confirm air flow through the unit. Caution: Do not use scissors or other sharp objects to remove a blockage from the nozzle as these may damage the motorized nozzle.
TROUBLESHOOTING Should you have any problem(s) with your vacuum cleaner, review the table below for solutions to minor performance issues. WARNING Disconnect electrical supply before performing maintenance to the vacuum cleaner. Failure to do so could result in electrical shock or personal injury. PROBLEM POSSIBLE CAUSE Battery may be depleted. Charge the battery as instructed. Wrong charger being used. Vacuum will not power on. SOLUTION Be sure to use only the charger supplied with your product.
Remove obstruction. Follow instructions Brush roll is jammed. on page 17. Brush roll needs to be reset. Brush roll in the motorized nozzle is not turning. Brush roll is not installed well. Turn the unit off and remove the obstruction, then turn back on. Remove brush roll and reinstall following instructions on page 17. Debris accumulates on metal contacts connecting the dust Remove the debris and reinstall cup and the main body of the following instructions on page 16. hand vacuum.
Battery may be depleted. The battery is overheated. Vacuum turns off Brush roll in the motorized on its own. nozzle is jammed causing motor protection system activated. Excessive loading on brush roll brush. The battery is damaged. Charge the battery as instructed on page 10. Let the battery cool down to reach a normal temperature, charge the battery. With the unit turned off, remove obstruction and then re-start. Turn the vacuum off and re-start. Call (866) 384-8432 for assistance.
