emission condenser Peltronic Manual

ManualsBrandsVACUUBRAND ManualsPumpsPC 3001 VARIOpro

Table Of Contents

Part I
Reset / Language selection
Safety information!
- Important information!
- General information
- Intended use
- Setting up and installing the equipment
- Ambient conditions
- Operating conditions
- Safety during operation
- Maintenance and repair
- ` Important information: Equipment marking (ATEX)
Technical data
- General technical data valid for all pumping units
- Gas inlet temperatures
- Wetted parts
- Abbreviations
- Pump parts
Use and operation
- Installing a pump in a vacuum system
- Notes regarding the (dry) ice condenser
- Notes concerning the operation of the inlet condenser IK
- Notes concerning the operation of the Peltronic emission condenser
- Notes concerning the operation of pumping units with silencer
- During operation
- Important notes regarding the use of gas ballast
- Important notes concerning the operation of the exhaust waste vapor condenser
- Shutdown & storage
- CVC 3000 Vacuum controller
Menu guide
Pump down function
Vac Control function
Auto mode
Program function
- Application example
VACUULAN function
Application examples
- Vacuum for filtration and suction
- Vacuum for gel dryer, drying chambers and vacuum concentrators
- Vacuum for distillation and evaporation (e.g., rotary evaporator)
- Vacuum for VACUU•LAN networks
Configuration
Part II
Readjustment of CVC 3000
Calibration in the factory
Cleaning the pressure transducer
Interface parameters
- Setting of the interface
- Read commands ”CVC 2000”
- Write commands ”CVC 2000”
- Read commands ”CVC 3000”
- Write commands ”CVC 3000”
Accessories
Troubleshooting
Replacing diaphragms and valves
- Cleaning and inspecting the pump heads
- Disassembling the housing cover at the side of the emission condenser
- Replacing the diaphragm
- Assembling the housing cover at the side of the emission condenser
- Disassembling the housing cover at the side of the ON/OFF switch
- Assembling the housing cover at the side of the ON/OFF switch
- Assembling the fittings
Cleaning and replacing components
Notes on return to the factory
Warranty
Health and safety clearance form
EC Declaration of Conformity of the Machinery

page 2 of 120

After sales service:

Contact your local dealer or call +49 9342 808-5500.

Dear customer,

Your VACUUBRAND diaphragm pumps are designed to provide you with

many years of trouble-free service with optimal performance. Our many

years of practical experience allow us to provide a wealth of application

and safety information. Please read these instructions for use before the

initial operation of your pump.

VACUUBRAND diaphragm pumps combine our many years of experi-

ence in design, construction and practical operation, with the latest de-

velopments in material and manufacturing technology.

Our quality maxim is the ”zero defect” principle:

Every diaphragm pump, before leaving our factory, is tested intensively,

including an endurance run of 14 hours. Any faults, even those which oc-

cur rarely, are identied and can be eliminated immediately.

After completion of the endurance run, every pump is tested, and must

achieve specications before shipment.

We are committed to providing our customers only pumps that meet this

high quality standard.

While our pumps cannot eliminate all of your work, we design, manufac-

ture and test them to ensure that they will be an effective and trouble-free

tool to assist you in that work.

Yours,

VACUUBRAND GMBH + CO KG

Trademark index:

VACUU•LAN

(US-Reg.No 3,704,401), VACUU•BUS

, VACUU•CONTROL

Peltronic

, VARIO

(US-Reg.No 3,833,788), VACUUBRAND

(US-Reg.No

3,733,388) and also the shown company logos are registered trademarks

of VACUUBRAND GMBH + CO KG in Germany and/or other countries.