User Manual Four-Channel GSM VoIP Gateway Model: GoIP4 Version 1.0, 2010/03 Tel: +1 (650) 963-7600 sales@vadcore.com support@vadcore.com www.vadcore.
Four-Channel GSM VoIP Gateway Contents 1 Product Introduction.................................................................................................. 3 1.1 General Information.....................................................................................................3 1.2 Protocol..........................................................................................................................3 1.3 Hardware Specification ............................................................
Four-Channel GSM VoIP Gateway 3.4.5 Codec Preference.................................................................................................................... 26 3.5 Call Divert....................................................................................................................27 3.5.1 Call Forward (From VoIP To PSTN)........................................................................................ 27 3.5.2 Call Forward (From PSTN To VoIP) ....................................
Four-Channel GSM VoIP Gateway 1 Product Introduction 1.1 General Information A VoIP GSM Gateway enables direct routing between IP and GSM network without the use of a FXO port or the PSTN network. With this device, the usage of VoIP is greatly enhanced with significant savings on long distance and roaming charges. 1.2 Protocol TCP/IP V4 (IP V6 auto adapt) ITU-T H.323 V4 Standard H.2250 V4 Standard H.245 V7 Standard H.235 Standard MD5 HMAC-SHA1 ITU-T G.711 alaw/ulaw, G.729A, G.
Four-Channel GSM VoIP Gateway Internet Control Message Protocol (ICMP) TFTP Client Hyper Text Transfer Protocol (HTTP) Dynamic Host Configuration Protocol (DHCP) Domain Name System (DNS) User account authentication using MD5 Out-band DTMF Relay: RFC 2833 and SIP Info 1.3 Hardware Specification ARM9E Processor DSP for voice codec and voice processing Two 10/100 BaseT Ethernet ports with full compliant with IEEE 802.3 LEDs for Ethernet port status Four GSM Channels’ Connection 1.
Four-Channel GSM VoIP Gateway 1.
） LAN Four-Channel GSM VoIP Gateway 1 ） 3） 4） 2 Connect this port to an Ethernet Switch/Router, the Ethernet of a DSL modem, or other network access equipment. PC Connect a computer or other network device to this port. POWER (DC12V/2000mA) Connect the 12V/2000mA Adapter provided to this power jack. Reset Press this button to reset the GoIP_4 Gateway to factory defaults.
Four-Channel GSM VoIP Gateway 2 Installation 2.1 Installation Steps Please follow the connection diagram above to install the GoIP4 Gateway. a) b) c) d) Insert a GSM SIM card in the SIM card compartment located at the bottom of the GoIP4 Gateway. Connect an Ethernet cable the LAN port of the GoIP4 Gateway and the other end to your existing network equipment. (Optional) Connect an Ethernet cable to the PC Port of the GoIP4 Gateway and the other end to a PC or other network device.
Four-Channel GSM VoIP Gateway 2.2 LED Indicators The following table defines the status of the LEDS located on the top case and on the RJ-45 connectors. LED DESCRIPTION P0WER When GoIP4 Working, this LED will keep light. RUN 1. When the GoIP4 is booting this LED will flash 100ms ON and 100ms OFF. 2. When the GoIP4 is login your softswitch, this LED will flash 1s ON and 1s OFF. LAN When LAN port is connected to network, this LED will light and flash when has data through this port.
Reboot device REBOOT Password Four-Channel GSM VoIP Gateway Not case-sensitive ： Note In command Reset and Reboot, the Password is the GoIP4 device’s admin password. The command keywords can be majuscule and lowercase, but the password is case-sensitive. 》 1 Obtain LAN Port IP Address Once the GSM SMS with message content “info” or “INFO” is received, the GoIP1 sends back a SMS message to the sender with the message content containing the LAN Port IP address.
Four-Channel GSM VoIP Gateway 3 Configuration Guide To configure the GoIP4 Gateway, you must login to its Web server via the LAN or PC port. The LAN port is factory preset to IP address 192.168.0.100 and the PC port is set to the fixed IP 192.168.8.1. If you lose the IP address information for LAN port, just dial a call to GoIP4 Gateway’s SIM card phone number. When the call is connected, you will hear a dial tone.
Four-Channel GSM VoIP Gateway 3.1 Web Configuration Menu If your computer is connected to the GoIP4 Gateway via the LAN port, you need to type the LAN IP address of the GoIP4 Gateway in your Web Browser to access the Web server of the GoIP4 Gateway. The default IP address on the LAN port is “192.168.0.100”. If your computer is connected to the GoIP4 Gateway via the PC port, you should type GoIP4’s PC port IP address (192.168.8.1) in the Web Browser.
Four-Channel GSM VoIP Gateway 3.2 Status The Status page shown below is the default / home page of the GoIP4 Web server.
Four-Channel GSM VoIP Gateway 3.2.1 Phone Information A. Serial Number Each Gateway has a unique serial number assigned by the factory such as GOIP409100019. This number is important for centralized configuration, technical support, and warranty. This number is printed on the bottom of the Gateway and is associated with your software license. B. Firmware Version Firmware version identifies the firmware version of the Gateway such as GHS-4.01-1. C. Hardware Mode This field shows terminal’s hardware type. D.
Four-Channel GSM VoIP Gateway this field displays LOGIN; otherwise, it displays LOGOUT. 3.2.2 Network Information A. LAN Port Configuration This field displays the status of the LAN port. B. PC Port Configuration This field displays the status of the LAN port. C. PPPoE If PPPoE is enabled, it displays its status. D. Default Route This field displays the IP address of the default routing Gateway. E. DNS Server This field displays the IP address of the Domain Name Server. 3.2.3 GSM Module Information A.
Four-Channel GSM VoIP Gateway Click on “Preference” in the left menu of the configuration web, and the screen will be displayed as below: 3.3.1 Language Currently GoIP4 only supports English. VADcore also has other versions of software that support Simplified Chinese and Traditional Chinese. Contact VADcore if you need other language support.
Four-Channel GSM VoIP Gateway 3.3.2 Time Zone and Time Server The GoIP4 Gateway supports Network Time Protocol (NTP) to obtain the date and time information from an NTP server (Time Server). The time zone is specified as in GMT ± offset. For example, the Pacific Standard Time is GMT-8, and the Pacific Daylight Time is GMT-7. Note: The GoIP4 Gateway supports CDR and Billing Information, it is important to set up these two parameters properly. 3.3.
Four-Channel GSM VoIP Gateway Each tone listed above is defined in the following format: nc, rpt, c1on, c1off, c2on, c2off, c3on, c3off, f1, f2, f3, f4, p1, p2, p3, p4 Where: nc is the number of cadences rpt is the repeat counter(0 - infinite, 1~n - repeat 1~n times) c1on is the cadence one on (in milliseconds) c1off is the cadence one off (in milliseconds) c2on is the cadence two on (in milliseconds) c2off is the cadence two off (in milliseconds) c3on is the cadence three on (in milliseconds) c3off is the
Four-Channel GSM VoIP Gateway 3.3.6 GSM Band GoIP4 Supported quad GSM bands: 850MHz, 900MHz, 1800MHz, 1900MHz. Select the correct GSM bands that are used in your country. 3.3.7 GSM ISP GoIP4 will show you a list of GSM ISPs When GoIP4 completes a search of ISPs. You can choose the ISP from the list and GoIP4 will just register to the one that you choose. 3.3.8 Auto Reboot This option enables GoIP4 to auto-reboot each day. GoIP4 will auto-reboot itself at Reboot Time.
Four-Channel GSM VoIP Gateway Single Server Mode: All four channels use same SIP account to connect to SIP server. Multiple Server Mode: Each channel use its own SIP account to connect to SIP server. Trunk Gateway Mode: GoIP4 will act as a SIP proxy. Remote SIP clients can register to GoIP4 and GoIP4 will process SIP requests on behalf of SIP client. GoIP4 Gateway’s SIP configure page as follow: ）Phone Number Enter a SIP phone number.
F) G) Four-Channel GSM VoIP Gateway registration, the current registration will time out. Check your SIP server for a reasonable value. Outbound Proxy Outbound proxy is a device that receives requests from a client, even though it may not be the server resolved by the Request-URI. Outbound proxy will forward SIP requests and frequently RTP media traffic to another SIP server.
Four-Channel GSM VoIP Gateway 3.4.2 Advanced Settings Click on “Advance Settings” tab on the top right corner of the Call Setting page to display all the parameters for programming, as shown below. These parameters allow more advanced control over the SIP signaling and media preference. ）Local Signaling Port (SIP Local port) The default SIP port is 5060. Change this as required. B）SIP 183 A Check the box of SIP 183 if the SIP server supports this feature.
Four-Channel GSM VoIP Gateway 3.4.3 Advanced Timing A) No Answer Expiry(32-180s), NICT Expiry(2-180s), Retransmit T1(200-2000ms), Retransmit T2(2000-8000ms) Some SIP proxies may have special timing requirements. Change these parameters as required. B DTMF Signaling 1 DTMF TYPE DTMF signals can be sent over to the called party after a call is established. GoIP4 Gateway supports both Inband and Outband DTMF signal types.
） Four-Channel GSM VoIP Gateway 2 DTMF Payload Type DTMF Payload Type is defined by RFC2833 protocol to carry the tone definitions for various applications. The default DTMF Payload Type is 101. Please consult your VoIP service provider for the proper setting if required. C Signaling Qos ） Signaling QoS improves the performance of SIP signaling. If local network device supports Qos, select this field accordingly. Please consult your network administrator for further information.
Four-Channel GSM VoIP Gateway ）RTP Port Range A This parameter specifies the range of the RTP (Real Time Protocol) Ports used by the GoIP4 Gateway. If your network limits the usable port range, this parameter may need to be modified. Please consult your network administrator for more information. B Packet Length(ms) This parameter defines the voice packet length. The default setting is 20ms. The range is from 5ms to 40ms at an increment of 5ms.
Four-Channel GSM VoIP Gateway GoIP4 Gateway supports different encryptions for voice media. Select the one that you prefer. F Symmetric RTP Normally GoIP4 Gateway uses RTP ports based on the configuration. If this box is checked, GoIP4 Gateway will identify RTP ports from the media traffic it has received and use the same ports when sending media traffic. G) Media NAT Traversal Similar to Signaling NAT Traversal, this feature allows media packets (RTP) to be routed properly in various network environments.
Four-Channel GSM VoIP Gateway 3.4.5 Codec Preference Click on “Media Settings” in the “Call Setting” menu and click Audio Codec Preference to access the parameters. Codec Preference allows a user to select the codes to be used and its priority for a voice call. Click on the check box to enable a codec. Select a codec and then press the UP or DOWN button to move the position of the codec on the codec list with a priority in descending order. Note: The voice code alaw and ulaw is G.711a and G.711u.
Four-Channel GSM VoIP Gateway 3.5 Call Divert The Call divert feature controls the routing of calls between VoIP and GSM. 3.5.
Four-Channel GSM VoIP Gateway Enter a phone number in this field will forward all incoming VoIP calls to this phone number (PSTN or Mobile). Using “,” to add a 500ms delay to the dialing sequence. When Forward Number field has a phone number, GoIP4 will automatically forward all VoIP calls to this phone number. When Forward Number is empty, GoIP4 will route phone calls based on the following conditions.
Four-Channel GSM VoIP Gateway 4) Password or Trust List Callers will be able to use GoIP4 for GSM connection if their phone numbers are on trust phone number list or if they have the password. SIM Card Settings 1) 2) 3) 4) SIM Card Expiry - usage limit (minutes) SIM Card State Report Number - the recipient phone number for the SMS report SIM Card State Report Time - the time schedule to send SMS report SIM Card ID - Identification sent with the sms message 3.5.
Four-Channel GSM VoIP Gateway Forward to VoIP Auth Mode This field sets protection for using the GSM connection to VoIP. 5) No Auth Anyone can make phone calls through GoIP4. 6) Password If a password is entered, the GoIP4 will generate an indication tone and wait for the caller to dial the password. 7) Trust List 8) Enter the phone numbers in the Trust Number field if Trust List is used. People calling from the trust phone numbers will be able to use GoIP4 to connect to VoIP.
Four-Channel GSM VoIP Gateway server is required to work with GoIP4 Gateway for SMS Sender. Please contact VADcore for more details. 3.6.2 SMS Call Out GoIP4 Gateway supported SMS call. In this mode, when GoIP4 Gateway receives a SMS from a mobile phone, it will automatically make a call to SIP server. To use this function, select the SMS Dial option in configuration page.
Four-Channel GSM VoIP Gateway A mobile phone’s number is (86)13800000000, it sends a SMS “8675588228822” to GoIP4’s GSM SIM card. When GoIP4 device receives this SMS, it will automatically call the number 8675588228822, and the caller is number 8613800000000. The sent-out signaling as follow: B. GoIP4 use SMS Dial Mode 1 and add a prefix as 999: A mobile phone’s number is (86)13800000000, it sends a SMS “8675588228822” to GoIP4’s GSM SIM card.
Four-Channel GSM VoIP Gateway Mode 2 example: GoIP4 use SMS Dial Mode 2: A mobile phone’s number is (86)13800000000, it sends a SMS “8675588228822” to GoIP4’s GSM SIM card. When GoIP4 device receives this SMS, it will automatically call the number 8675588228822, and the caller number is GoIP4’s SIP account number. GoIP4 will set the SMS sender number to “Call Divert “option’s “Forward Number (VoIP to PSTN” automatically.
Four-Channel GSM VoIP Gateway SMS prefix can be used in mode 2 just like in mode 1. Mode 3 example: GoIP4 use SMS Dial Mode 3: A mobile phone’s number is (86)13800000000, it sends a SMS “8675588228822” to GoIP4’s GSM SIM card. When GoIP4 device receives this SMS, it will automatically call the number 8675588228822*(86)13800000000, and the caller number is GoIP4’s SIP account number.
Four-Channel GSM VoIP Gateway SMS prefix can be used in mode 3 just like in mode 1. 3.6.3 SMS Relay GoIP4 GSM Gateway supports SMS relay. The SMS Forward Number is the receiver (ex. an extension) on your VoIP system. GoIP4 will forward the SMS it received to the number. 3.6.3.1 SMS Relay To VoIP System When GoIP4 receives a SMS from GSM network, it will relay to VoIP system’s appointed number (SMS Forward Number).
Four-Channel GSM VoIP Gateway 3.6.3.2 SMS Relay To GSM Network When GoIP4 receives a message from SIP server as below: The GoIP4 will send a SMS to GSM number 13682626800, the SMS content is “Hello world”.
Four-Channel GSM VoIP Gateway 3.7 GSM Caller ID Transparent GoIP4 supports GSM Caller ID transparent to VoIP via SIP Invite signaling. A) Disable: Disable GSM Caller ID transparent to VoIP. B) Use Remote Party ID: GoIP4 will add Caller ID in SIP invite’s Remote Party ID option. C) Use CID as SIP Caller ID: GoIP4 use PSTN Caller ID in SIP invitee’s Caller ID option and Remote Party ID option.
Four-Channel GSM VoIP Gateway 3.8 GSM Group Mode GoIP4 can group multiple devices together and provide line-hunt. The Group Mode works like a multi-channels GSM gateway. Any GoIP4’s channel can work as Group Server Mode or Client Mode.
Four-Channel GSM VoIP Gateway Server Mode: Only one GSM channel runs in Server Mode. The GSM channel that is set in Server Mode will forward the GSM’s incoming calls to other available client channels. The GSM channel that is set in Server Mode will be your main number for your customer. Client Mode: Other GSM channels will run in Client Mode. The GSM channels that are set in Client Mode will report their status to GSM channel that is set in Server Mode.
Four-Channel GSM VoIP Gateway The basic syntax is “:|:|…”, where defines the event to be matched. An event consists of a sequence of digits. If a specific digit has a limited range, use the syntax [A-B] where A and B are both digit (0 to 9) and B is greater than A. The length of the input number can be limited by using “X” to represent each unknown digit. If this field is omitted, it means any event.
Four-Channel GSM VoIP Gateway 2. Dial Plan = “1:+00” means that two digits “00” will be added in front of the number when the first digit of the dialed number is “1”. a) Number entered = “1082121234”, actual number dialed = “00182121234”. b) Number entered = “82121234”, actual number dialed = “82121234”. 3. Dial Plan = “001:-001+1751” means that the first 3 digits “001” of the dialed number will be changed to “1751” when a number with first three digits “001” is entered.
Four-Channel GSM VoIP Gateway Note: A too low or too high gain MAY affect the sensitivity of DTMF detections. 3.11 Network Configuration Click on “Network” tab in the left menu column to configure the LAN and PC ports.
Four-Channel GSM VoIP Gateway 3.11.1 LAN Port Three LAN Port modes are supported: DHCP, Static IP and PPPoE. The default is set for Static IP with default IP address “192.168.0.100”. ） 1 DHCP Choose DHCP if a local DHCP host is available. This allows the GoIP4 Gateway to obtain network information (IP Address, Subnet Mask, Default Route, Primary DNS, Secondary DNS, and other DHCP options) from the DHCP host.
Four-Channel GSM VoIP Gateway The default setting of GoIP4 is Static IP with IP address “192.168.0.100” and Subnet Mask “255.255.255.0”. However, Default Route, Primary DNS, and Secondary DNS (optional) must be manually entered according to your network configuration. PPPoE ） 3 PPPoE is a common method for you network modem (Cable / xDSLs). Choose this if your network environment requires. Enter the User Name and Password as provided by your ISP. 802.
Four-Channel GSM VoIP Gateway 3.11.2 PC Port Configurations The PC Port allows other network devices to be attached to the GoIP4 Gateway. It offers both Bridge and Static IP modes to meet your requirements. The factory preset is Static IP mode with the IP address 192.168.8.1. ）Bridge Mode 1 Select Bridge mode if your network topology requires the network devices (PC or others) to be in the same network segment as the GoIP4 Gateway. In this case, the GoIP4 Gateway functions as an Ethernet Switch.
Four-Channel GSM VoIP Gateway Specify the Starting Address, Ending Address, and Static DNS accordingly. ） Advanced 4 The Advanced settings allow the user to set the broadcast address and to clone a MAC address instead of using the factory preset MAC address. Please consult your network administrator for further information. 3.12 Save Configuration To confirm and commit all changes that have been made, click on the Save Changes tab. Otherwise, all changes will be discarded. 3.
Four-Channel GSM VoIP Gateway 3.14.1 Online Upgrade To perform a firmware upgrade, select the Online Upgrade tab to access the page below. Enter the update link as provided by VADcore. A sample link is: hk.ippcn.com/update/GHS-3.01-18.pkg Click the Start button to start the firmware upgrade. WARNING: POWER SHUTDOWN, POWER FAILURE OR UNPLUG POWER ADAPTOR FROM GoIP4 DURING FIRMWARE UPGRADE MAY PERMINENTLY DAMAGE THE GOIP4 GATEWAY AND VOID THE WARRANTY. 3.14.
Four-Channel GSM VoIP Gateway ）User Password A This is the password for the user ID “user”. The default password is “1234”. user ID has limited access to the Network Configuration menu. B This ）Administrator Password (default: admin) This is the password for the user ID “admin”. The default password is “admin”. This user ID has full access to all configuration settings available. 3.14.3 Reset Configuration Click on the Reset Config tab to reset the GoIP4 Gateway to its factory default settings. 3.
Four-Channel GSM VoIP Gateway 4 Hardware Specifications Characteristics of the hardware Parameter Processor ARM9E 133MHz DSP VPDSP101-4 RAM 16M Flash 4M Power DC12V/2000mA +-10% Default Remarks 100MHz Input AC100V to AC240V 850MHz/1900MHz GSM Module Type Optional 900MHz/1800MHz Consumption The Maximum 5 W LEDs RUN, GSM, LAN, PC,GSM Network Ports 2 RJ45; Supported NAT 100/10BASE-T Weight 900 Grams Full Set Working Temperature 0 40 Working Humidity － ℃ 40％－90％ Not Congealed Colo
Four-Channel GSM VoIP Gateway Time Zone ＋ GMT 8 50
