Specifications

AutoTrak 2.0 Camera Tracking System
AutoTrak 2.0 Camera Tracking System - Document Number 342-0382 Rev. B Page 5 of 52
UNPACKING:
Carefully remove all of the parts for the AutoTrak 2.0 999-7250-001 (Int’l) Dual HD-18 Kit with Quick
Connect DVI/HDMI Interface) packaging:
 One (1) AutoTrak 2.0 CPU (closed system preloaded with AutoTrak 2.0 software and video card)
 One (1) Euro Power Cord for AutoTrak 2.0 CPU
 One (1) UK Power Cord for AutoTrak 2.0 CPU
 One (1) PS/2 Keyboard and PS/2 Mouse
 One (1) IR and Audio Lanyard with attached cable with 5-pin mini XLR connector
 One (1) Audio-Technica AT8439 Cable Clip to attach Lanyard Central Medallion to clothing
 One (1) Triple Circle Magnet Kit for attaching the Lanyard Central Medallion to clothing
 One (1) Belt Pack Unit “BPU” with 1” (1/4 wave) RP-SMA straight antenna and attached belt clip with
rechargeable lithium ion battery pack
 One (1) 5 VDC USB Charging Supply for Europe
 One (1) 5 VDC USB Charging Supply for UK
 One (1) USB Type A-Male to micro-B-Male Charging Cable
 One (1) Vaddio PowerRite 12 VDC, 1A Switching Power Supply
 One (1) Euro Power Cord
 One (1) UK Power Cord
 One (1) AutoTrak POD Kit (for presets and rescan) and Manual (in separate box)
AutoTrak 2.0-Dual HD-18 Kit:
 One (1) *HD-18 PTZ Camera with AutoTrak 2.0 Software preloaded - Tracking Camera
 One (1) Quick-Connect SR Interface (998-1105-016) for Tracking Camera
 One (1) 24VDC, 2A, Switching Power Supply
 One (1) Euro Power Cord
 One (1) UK Power Cord
 One (1) *HD-18 PTZ Camera with AutoTrak 2.0 Software preloaded - IR Reference Camera
 One (1) 37mm female lens ring adapter, One (1) 37mm to 58mm adapter ring, One (1) 58mm
polarizing filter, One (1) 58mm band-pass IR filter, all parts adapters and filters attached to HD-18
Camera
 One (1) AutoTrak 2.0 Quick-Connect Box (998-1105-020)
 One (1) Standard Quick-Connect Box (998-1105-001)
 One (1) 24VDC, 2A, 50/60Hz 110-240V Switching Power Supply (451-2000-0024)
 One (1) Euro Power Cord
 One (1) UK Power Cord
 One (1) 18”/45.8cm Video Cable (BNC to RCA)
 One (1) 12”/30.48cm Cat 5e Patch Cable
 One (1) 998-2100-000 - Vaddio IR Remote & Manual (2-AAA batteries not included)
 One (1) **535-2000-233 Stacked Gusseted Mount for two (2) HD-18 and Mounting Hardware
 Three (3) 998-1001-232 Control Adapters
 One (1) 998-7200-232 Control Adapter for use with the AutoPresenter - (Only needed when used with
the AutoPresenter for Tracking Camera PTZ Presets)
 Documentation and Manuals (Document Number (342-0382)
For the 999-7260-001 System - Start with the 999-7250-001 System
Remove: One (1) *HD-18 PTZ Camera with AutoTrak 2.0 Software preloaded - Tracking Camera
Add: One (1) *HD-20 PTZ Camera with AutoTrak 2.0 Software preloaded - Tracking Camera
*Note 1: The Vaddio HD-18 and HD-20 cameras are preloaded with AutoTrak 2.0 control protocols which
differ from the modified VISCA type control codes normally used in the stock HD-18 PTZ Camera. The
HD-18 and HD-20 cameras will work with the Vaddio IR Remote but is recommended that the PTZ
positions of the camera be set with the AutoTrak 2.0 Software. The HD-18 and HD-20 AutoTrak 2.0
cameras will not work with any other controller other than AutoTrak 2.0 at this time.
**Note 2: The stacked camera arrangement is required for the AutoTrak 2.0 software to track properly.