Owner manual

ManualsBrandsVaddio ManualsAudioCeilingVIEW 70 Manual

Installation and User Guide

Camera and Electronic Products for Integrators

pricing are subject to change without notice. CeilingVIEW, WallVIEW, EZCamera, Quick-Connect and PowerRite are registered

trademarks of Vaddio, Inc. All other trademarks are property of their respective owners. Form Number 010-2304-000 Rev. E

CeilingVIEW 70 PTZ

Integrated, Recessed Installation Pan/Tilt/Zoom Ceiling Camera System

Vaddio’s CeilingVIEW 70 PTZ camera system is designed to

provide system integrators with an easy to install, partially

recessed, in-ceiling camera system (see Figure 1). The system

features a Sony® EVI-D70 PTZ Camera mounted into a shallow

recessed, metal ceiling camera enclosure with ceiling tile support

and is equipped with Vaddio’s EZCamera™ Cabling System which

allows the integrator to use Cat. 5 cabling to run power, video and

camera control.

IR Remote Control or RS-232 can control the camera pan/tilt/zoom

and electronic functions. The VISCA control interface is included to

allow the camera to work with any other VISCA compatible control

device that supports the full range of motion that the camera

supplies. The PowerRite™ power supply regulates the right amount

of power needed for the camera over the Cat. 5 cabling.

Before operating the Vaddio CeilingVIEW 70 PTZ, please read the

entire manual thoroughly. The camera system was designed, built

and tested for use indoors in a suspended acoustic tile ceiling, and

with the provided power supply. The use of a power supply other

than the one provided or outdoor operation has not been tested and

could damage the camera and/or create a potentially unsafe

operating condition.

The information contained in this manual will help you install and

operate your Vaddio CeilingVIEW 70 PTZ. If these instructions are

misplaced, Vaddio keeps copies of Specifications, Installation and

User Guides and most pertinent product drawings for the Vaddio

product line on the website. These documents can be downloaded

from www.vaddio.com

free of charge.

SAVE THESE

INSTRUCTIONS

INTENDED USE

INTRODUCTION

Figure 1: Vaddio

CeilingVIEW 70 PTZ

Camera System

partially recessed

into the ceiling

Summary of content (14 pages)

PAGE 1
Installation and User Guide Camera and Electronic Products for Integrators CeilingVIEW 70 PTZ Integrated, Recessed Installation Pan/Tilt/Zoom Ceiling Camera System Figure 1: Vaddio CeilingVIEW 70 PTZ Camera System partially recessed into the ceiling INTRODUCTION Vaddio’s CeilingVIEW 70 PTZ camera system is designed to provide system integrators with an easy to install, partially recessed, in-ceiling camera system (see Figure 1).
PAGE 2
IMPORTANT SAFEGAURDS Read and understand all instructions before using. Do not operate the camera if the camera has been dropped or damaged. In this case, a Vaddio technician must examine the product before operating. To reduce the risk of electric shock, do not immerse in water or other liquids and avoid extremely humid conditions. Use only the power supply provided with the CeilingVIEW 70 PTZ camera system. Use of any unauthorized power supply will void any and all warranties.
PAGE 3
Note: If camera is to be controlled as part of a multi camera system, please refer to the section CHANGING CAMERA DEFAULT SETTINGS located on Page 6 of this manual. Step by Step Mounting Instructions To mount the CeilingVIEW 70 PTZ: 1) Attach a string or plumb bob to the ceiling tile with a thumbtack. 2) Position the string directly over ample table space or work surface to allow easy document and object positioning.
PAGE 4
Cabling the Camera 7) The Cat.5 plenum rated cable (not included) is run from the ceiling location where the camera is to be mounted, to where the Quick-Connect Box is located (see Figure 5). Both the SVideo and Composite Video outputs are active. Cat. 5 to/from POWER/VIDEO Jack on Camera Module Figure 5: Quick-Connect Box and connections S-Video Output to Display Device Composite Video Output to Display Power from PowerRite Power Supply 8) If needed, Cat.
PAGE 5
Finishing Up 10) The camera and ceiling tile should be carefully replaced in the suspended ceiling at this time. 11) Locate the white trim ring assembly and plug the IR cable into the IR board connector on the trim ring lip (see Figure 8). Take care not to pull any more than about 2 inches of cable from the camera enclosure. The connectors will fit together only one way with a positive click.
PAGE 6
Figure 9: RM-EV100 IR Remote Controller • Power on/off • Camera Select: 1, 2, 3 • Focus: Auto, Manual (Near & Far) • Zoom: Slow – Tele, Wide Fast – Tele, Wide • Data Screen On Screen Display • Back Light: Back Light Compensation • Pan-Tilt: Left, Right, Up, Down, Reset • Home: Home/Centered Position • Position: Preset, Reset • Presets: 6 (1 through 6) • L/R Direction Set: Std, Rev Control Systems CHANGING CAMERA DEFAULT SETTINGS If you are using a control system (i.e. Crestron or AMX), plug the Cat.
PAGE 7
RS-232 COMMAND LIST Communication Specification Control Disclaimer Vaddio supplies this control specification for the CeilingVIEW 70 PTZ camera. This VISCA control set (as used in Sony EVI cameras) is used in conjunction with additional Vaddio control commands (see comment section on Table 1) for added functionality of the camera lift.
PAGE 8
One Push Trigger Command List (Continued) 8x 01 04 18 01 FF One Push AF Trigger Infinity 8x 01 04 18 02 FF Forced Infinity Near Limit 8x 01 04 28 0p 0q 0r 0s FF pqrs: Focus Near Limit Position Normal 8x 01 04 58 02 FF AF Sensitivity Norm/Low Low 8x 01 04 58 03 FF AF Sensitivity CAM_ZoomFocus CAM_WB Direct 8x 01 04 47 0p 0q 0r 0s 0t 0u 0v 0w FF pqrs: Zoom Position tuvw: Focus Position Auto 8x 01 04 35 00 FF Normal Auto Indoor 8x 01 04 35 01 FF Indoor Mode Outdoor 8x 01 04 35 02 FF
PAGE 9
Down Command List (Continued) 8x 01 04 0C 03 FF Direct 8x 01 04 4C 00 00 0p 0q FF pqrs: Gain Position Reset 8x 01 04 0D 00 FF Bright setting Up 8x 01 04 0D 02 FF Down 8x 01 04 0D 03 FF Direct 8x 01 04 4D 00 00 0p 0q FF pqrs: Bright Position On 8x 01 04 3E 02 FF Exposure Compensation ON/OFF Off 8x 01 04 3E 03 FF Reset 8x 01 04 0E 00 FF Up 8x 01 04 0E 02 FF Down 8x 01 04 0E 03 FF Direct 8x 01 04 4E 00 00 0p 0q FF pqrs: ExpComp Position On 8x 01 04 33 02 FF Back Light Compensati
PAGE 10
(8x 01 06 06 02 FF) Command List (Continued) 8x 01 04 15 03 FF Off (8x 01 06 06 03 FF) 8x 01 04 15 10 FF On/Off (8x 01 06 06 10 FF) Title Set1 8x 01 04 73 00 mm nn pp qq 00 00 00 00 00 00 FF mm: V-Position, nn H-Position pp: Color, qq:Blink 8x 01 04 73 01 mm nn pp qq rr ss tt uu vv ww FF mnpqrstuvw: Set of charactors ( 1 to 10) Title Set3 8x 01 04 73 02 mm nn pp qq rr ss tt uu vv ww FF mnpqrstuvw: Set of charactors ( 11 to 20) Title Clear 8x 01 04 74 00 FF Title Set clear On 8x 01 04 74 02 FF
PAGE 11
RS-232 Connection The RJ-45 Connector labeled RS-232 IN (see page 4) has the following pin-outs. The DSR and DTR are added to the Vaddio CeilingVIEW 70 PTZ and other Vaddio products to support the Sony Daisy-chain control standard (see Figure 11). Figure 11: RS-232 IN pin-outs for RJ-45 connector on back of CeilingVIEW 70 PTZ CARE AND CLEANING OPERATING CONDITIONS Do not attempt to take the camera module apart (other than for the reasons stated in the manual).
PAGE 12
TROUBLESHOOTING Problem Questions for Troubleshooting No image Camera will not respond to IR Remote Camera will not respond to control system RS232 control commands SPECIFICATIONS Is the Vaddio supplied power supply connected to a working AC wall outlet? Is Vaddio power supply securely connected to wall plate or Quick Connect box? Is the Category 5 signal cable securely connected to the Quick Connect box? Is the Category 5 signal cable connected to correct port on the camera? Have fresh AA batteries
PAGE 13
COMPLIANCE FCC Part 15 Compliance and EC Declaration of Conformity Sony Corporation holds the FCC and CE certifications for the EVI-D70 and EVID70P cameras used internal to the CeilingVIEW 70 PTZ mechanical enclosure. Please contact Sony Corporation for this documentation. WARRANTY INFORMATION Hardware* Warranty - One year limited warranty on all parts.
PAGE 14
9433 Science Center Drive ▪ New Hope, MN 55428 Toll Free: 800-572-2011 ▪ Phone: 763-971-4400 ▪ FAX: 763-971-4464 www.vaddio.com Ⓒ2006 Vaddio - All Rights Reserved. Reproduction in whole or in part without written permission is prohibited. Specifications and pricing are subject to change without notice. CeilingVIEW, WallVIEW, EZCamera, Quick-Connect and PowerRite are registered trademarks of Vaddio, Inc. All other trademarks are property of their respective owners. Form Number 010-2304-000 Rev. E.