Installation and User Guide EasyTalk™ Wireless USB Mic System Part Numbers: 999-8550-000 North America 999-8550-001 International ©2012 Vaddio - All Rights Reserved.
EasyTalk Wireless Mic Table of Contents Overview: ................................................................................................................................................................... 3 Unpacking: ................................................................................................................................................................. 4 Diagram: The Front Panel Controls:......................................................................................
EasyTalk Wireless Mic Overview: The EasyTalk Wireless USB Mic System expands audio capabilities for live voice reinforcement with its analog outputs or lecture capture with its USB 2.0 digital audio output plugged directly into a computer. Key features of the EasyTalk Wireless Audio Interface include: HD Wireless Link with Adaptive Frequency Hopping (AFH) for interference free operation. USB Audio Output allowing connection to a PC for UC Soft-client Applications or Lecture Capture systems.
EasyTalk Wireless Mic Unpacking: Carefully remove all of the parts for the EasyTalk Wireless USB Mic System from the packaging. 999-8550-000 for North America includes: One (1) 998-8550-000 EasyTalk Wireless Receiver Two (2) Rack Ears for Rack Mounting the Receiver One (1) 2.39GHZ-2.51GHz ½-Wave, 3.5” RP-SMA Right Angle, Antenna 12 VDC, 1.0 Amp PowerRite™ Power Supply with North American Power Cord One (1) 6’ (1.83m) USB 2.
EasyTalk Wireless Mic 4) Volume: The + (plus) and – (minus) buttons are used to raise and lower the audio outputs (Balanced and Unbalanced) from the EasyTalk Wireless Receiver. 5) Audio Level: This LED display ladder will indicate the relative audio level output (from all sources) of the EasyTalk Wireless Receiver. The red line at the top of the display indicates clipping. 6) Radio, EQ Filter and Compressor Status LED’s: Radio LED: Solid blue light indicates normal operation.
EasyTalk Wireless Mic Table: Dip Switch Settings and Descriptions Dip Switch # 1 2 3 4 5 6 7 8 Function ON/OFF - Enable/Disable - Compressor for the Balanced and Unbalanced Audio Outputs ON/OFF - Enable/Disable - Speaker EQ Filter ON/OFF - USB Conference Mode (Skype-type PC applications) ON/OFF - ON Enables Radio, OFF Disables Radio ON/OFF - Baud Rate Selection: 9600-Off/38.
EasyTalk Wireless Mic Diagram: Belt Pack Control Panel ① ⑤ ② ③ ④ 1) Lav Mic Cable Connector (5-pin mini XLR - M): Plug the cable attached to the Lanyard into the 5-pin mini XLR connector. 2) Radio: This LED indicates an active radio link with the EasyTalk Wireless Receiver. Solid blue LED indicates connection with the EasyTALK Wireless Receiver. Flashing blue LED indicates radio link has been lost.
EasyTalk Wireless Mic Belt Pack and Battery Compartment: Diagram: Belt Pack Views ④ ① ⑤ ③ ② ⑥ 1) Removable Battery Compartment Cover: To open, carefully press down at the top of the removable battery cover near the center of the small opening and slide the cover downward. To replace the removable battery cover, start sliding the cover on at the bottom of the battery pack compartment and slide cover upward to the top to the small opening until the cover latches in place.
EasyTalk Wireless Mic Table: Belt Pack Dip Switch Settings: Switch Number 1 2 3 4 1 2 3 4 Dip Switch Function Switch Set 4 (SW4) Not Used ON/OFF - IR LED’s in Lanyard ON/OFF - Radio in Belt Pack *Turn off when not using Optional EasyTalk Wireless Receiver Clear Pairing (pairing is required for proper operation) Switch Set 5 (SW5) ON/OFF: ON adds 3dB Gain Boost on Microphone ON/OFF: ON adds 6dB Gain Boost on Microphone ON/OFF: ON adds 9dB Gain Boost on Microphone ON/OFF: Automatic Gain Control Mode SW5 SW
EasyTalk Wireless Mic Step by Step Instructions For setting up the EasyTalk Wireless Mic System: Step 1: Review the manual to eliminate any and all surprises. Step 2: Connect the 3.5” right-angle RP-SMA antenna to the front of the receiver and connect the power supply. Step 3: Connect the audio outputs (Balanced, Unbalanced or USB) to the audio system (not included). Set all audio levels on the audio system low to avoid any rude awakenings.
EasyTalk Wireless Mic Diagrams: Basic Configurations Computer (Not included) HD-USB Camera (Not included) Leer Jet (Not included) USB 2.0 Video UVC Drivers USB 2.
EasyTalk Wireless Mic Compliance and CE Declaration of Conformity: EasyTalk Wireless Receiver and Belt Pack Transmitter Compliance testing was performed to the following regulations: FCC Part 15 Subpart B FCC Part 15, Subpart C Section 15.247 FCC Part 15, Subpart C Section 15.207 Industry Canada RSS-210 Issue 8 Industry Canada RSS-Gen Issue 3 Class A Class A Class A Class A IEC 60950-1/A1: 2009 Safety ETSI EN 300 328 V1.7.
EasyTalk Wireless Mic Warranty Information: (See Vaddio Warranty, Service and Return Policies posted on vaddio.com for complete details): Hardware* Warranty: One year limited warranty on all parts. Vaddio warrants this product against defects in materials and workmanship for a period of one year from the day of purchase from Vaddio. If Vaddio receives notice of such defects during the warranty period, they will, at their option, repair or replace products that prove to be defective.
EasyTalk Wireless Mic Appendix 1: Pin-outs and Stuff RS-232 Control: DE-9 Female (DB-9 for convention): Communication Specification Communication Speed: 9600 bps or 38,400 Stop bit: 1 Data bits: 8 Parity: None No Flow Control Control Port - RS-232 on DE-9 Female Connector PIN# Signal 2) TXD 3) RXD 5) GND All other pins - Unused EasyTalk Audio User Serial Command Set: The EasyTalk Wireless Receiver has an RS-232 command interface for configuration and real-time control.
EasyTalk Wireless Mic Command Response 5112 4112 Argument Available w/ DIP 7 Down Y n/a Description Get mixer enabled Mixer enabled response Y n/a Get radio enabled Radio enabled response Y n/a Get power enabled Power enabled response Y Set mute on or off Y Adjust volume by +1dB or -1dB N Enable/disable compressor N Enable/disable filter N Enable/disable USB mix N Enable/disable radio N Y Y Reset to factory default settings Power on/off Enable/disable command echo and prompt n/a Comm
EasyTalk Wireless Mic 9433 Science Center Drive, Minneapolis, MN 55428 Toll Free: 800-572-2011 ▪ Phone: 763-971-4400 ▪ FAX: 763-971-4464 www.vaddio.com ©2012 Vaddio - All Rights Reserved. Reproduction in whole or in part without written permission is prohibited. Specifications and pricing are subject to change without notice. Vaddio and EasyTalk are trademarks of Vaddio. All other trademarks are property of their respective owners. Document 342-0442USB Rev.
