Installation and User Guide Installation andControllers User Guide Cameras and For Integrators VADDIO™ ONELINK™ FOR CISCO® SELECT PRECISIONHD CAMERAS OneLINK - High Speed Digital Bus for HD Digital Video, Power and Control Over One Cat-5e Cable Part Numbers: 999-9550-000 North America 999-9550-001 International For the Cisco PrecisionHD 1080p 12x and the PrecisionHD 720p Cameras ©2012 Vaddio - All Rights Reserved. OneLINK for Cisco Precision HD Cameras - Installation and User Guide 342-0122 Rev.
OneLINK Inside Front Cover - Blank OneLINK for Cisco Precision HD Cameras - Installation and User Guide 342-0122 Rev.
OneLINK Overview: The Vaddio OneLINK for Cisco Precision HD Cameras is built for use with the Cisco PrecisionHD 1080p 12x and PrecisionHD 720p high definition PTZ cameras and the Cisco C20, C40, C60 and C90 codecs (camera and codec not included).
OneLINK Unpacking Carefully remove all of the parts from the shipping box. Unpack and identify the following parts for the OneLINK system for Cisco PrecisionHD camera: One (1) EZIM OneLINK (EZ Interface Module) One (1) Quick-Connect OneLINK (1-RU, ½ rack width) One (1) Thin Profile PrecisionHD Wall Mount for OneLINK with Mounting Hardware One (1) EZCamera Control Adapter (998-1008-232) for OneLINK One (1) 48 VDC, 1.
OneLINK GENERAL SYSTEM CONNECTIVTY: Basic OneLINK System (Quick-Connect & EZIM) with Cisco Camera and C-Series Codec EZIM OneLINK 12V Power RS-232 HDMI One Cat 5e Cable Up to 125’ (38.
OneLINK INSTALLATION INSTRUCTIONS Installation is simplified in that no custom cables or expensive multi-coax plenum cables are needed and no local power outlets are required near the camera bracket. All RJ-45 connectors are to be terminated using TIA/EIA 568B standard. Before installing the OneLINK System: Choose a camera mounting location while paying close attention to camera viewing angles, lighting conditions, possible line of site obstructions, and checking for in-wall obstructions.
OneLINK Step 6: Attach the PrecisionHD camera to the mount with the provided ¼” x 20 screw, tie up the cables neatly and connect the Cat-5e cable from the head end to the connector labeled OneLINK as shown below. Camera Location Do not use cable #116627 supplied with the codec on this Camera Control Port OneLINK Cat-5e Up to 125’ (38.1m) Head End Location Step 7: At the head end, connect the Cat-5e cable from the camera location to the OneLINK port on the Quick-Connect OneLINK port as shown above.
OneLINK Step 9: With the Codec turned off, connect the 48 VDC power supply to the Quick-Connect OneLINK. The blue LED power light will illuminate and it is ready for the codec to be booted up. Note: If the OneLINK Cat-5e cable is incorrectly terminated or if intermittent connections are the result of the use of pass-thru, EZ type RJ-45 connectors, damage to the system may result. If the units are damaged due to improper cabling, then all implied or expressed warranties are automatically voided.
OneLINK WARRANTY INFORMATION (See Vaddio Warranty Policies posted on vaddio.com for complete details): Hardware* Warranty - One year limited warranty on all parts. Vaddio warrants this product against defects in materials and workmanship for a period of one year from the day of purchase from Vaddio. If Vaddio receives notice of such defects during the warranty period, they will, at their option, repair or replace products that prove to be defective.
OneLINK Compliance and CE Declaration of Conformity Compliance testing was performed to the following regulations: FCC Part 15, Subpart B ICES-003, Issue 4: 2004 EN 55022 A: 2006 + A1: 2007(CISPR 22:2005/A1:2005) AS/NZS CISPR 22: 2009 VCCI V-3/2010.
OneLINK NOTES: OneLINK for Cisco Precision HD Cameras - Installation and User Guide 342-0122 Rev.
OneLINK 9433 Science Center Drive, Minneapolis, MN 55428 Toll Free: 800-572-2011 ▪ Phone: 763-971-4400 ▪ FAX: 763-971-4464 www.vaddio.com ©2011 Vaddio - All Rights Reserved. Reproduction in whole or in part without written permission is prohibited. Specifications and pricing are subject to change without notice. Vaddio, Quick-Connect, OneLINK, EZIM, EZCamera, HSDS, SHSDS, and PowerRite are trademarks of Vaddio. All other trademarks are property of their respective owners.- Installation Document Number Rev.