Manual

ManualsBrandsVaddio ManualsAudioThin Profile Wall Mount Bracket for CISCO Set-top Codecs

Vaddio Wall Mount Shelf for TANDBERG Set-top Series Codecs Part Number 535-2000-250 Page 1 of 2

Installation and User Guide

Vaddio™ Wall Mount Shelf for TANDBERG Set-top Series Codecs

For Wall Mounting TANDBERG 990/880/770/550 MXP Set-top Codecs

Model Number 535-2000-250

OVERVIEW:

The Vaddio Wall Mount Shelf for the TANDBERG

set-top series codecs is an attractive and practical

method for mounting Set-top codecs directly to the

wall above plasma displays or above thin-line rear

projection monitors where the codec cannot fit

directly on top of the display. The key features of

the Vaddio Shelf are:

 Designed to fit the contours and geometry of the

codec while echo the design elements

 Encloses the back plane of the codec and hides

the cabling and connectors

 Constructed from lightweight aluminum and

welded for strength and rigidity

 Black powder coat paint provides an attractive,

tough and lasting finish

 Ample space for connectors, cables & adapters

(i.e. DVI to DB-15HD adapter and cable)

 Key-hole mounting holes for speedy installations

and easy camera leveling

 Large access opening in back for full access to

in-wall cabling

UNPACKING:

Carefully remove the product and all of the parts from the packaging. Unpack and identify the following parts:

 One (1) Wall Mount Shelf for TANDBERG Set-top Codec, Part Number 535-2000-250

 Two (2) Black Plastic Mounting Screw Access Caps

 Four (4) #8 x 1- ¼” Sheet Metal Screws

 Four (4) Spiral type drywall anchors

 Manual (Document Number 341-482)

INSTALLING THE WALL MOUNT SHELF:

Note: When locating the set-top codec shelf, consider viewing angles, lighting conditions, possible line of site

obstructions and check for in-wall obstructions where the camera is to be mounted. Pick a mounting location to

optimize the performance of the camera. Read the step-by-step instructions fully before starting the installation.

1. Position the shelf against the wall, level the shelf and mark the hole pattern of the shelf to the wall with a long

pencil. For the top key-holes, mark the top of the key-hole. The hole pattern is shown below (Figure 3).

Camera and Electronic Products for Integrators

Figure 3:

Hole pattern measurements on

the back of the shelf - mark the

top part of the key-hole for

placement of wall anchor, mark

the lower screw holes, and trace

the 11” x 3-½” opening on the

wall with a long pencil.

Figure 2: Rear View of Wall Mount Shelf

Figure 1:

Isometric View of

Wall Mount Shelf

11” x 3-½” cable opening

Summary of content (2 pages)

PAGE 1
Installation and User Guide Camera and Electronic Products for Integrators Vaddio™ Wall Mount Shelf for TANDBERG Set-top Series Codecs For Wall Mounting TANDBERG 990/880/770/550 MXP Set-top Codecs Model Number 535-2000-250 OVERVIEW: The Vaddio Wall Mount Shelf for the TANDBERG set-top series codecs is an attractive and practical method for mounting Set-top codecs directly to the wall above plasma displays or above thin-line rear projection monitors where the codec cannot fit directly on top of the display.
PAGE 2
Installation (continued) 2. Reaching through the body of the shelf, trace the 11” (27.94cm) x 3-½” (8.89cm) opening on the back of the shelf to the wall. Within this area, the in-wall cabling will enter the back of the shelf. Cut the opening into the wall for in-wall cabling smaller than the 11” x 3-½” area to ensure that the shelf covers the hole completely. If a wall box is used, use a single gang wall box mounted horizontally within the 11” x 3-½” area. 3.