Installation and User Guide Installation and User Guide VADDIO™ QUICK-CONNECT™ UNIVERSAL CCU FOR WALLVIEW™ HD-22 AND HD-30 CAMERAS WallVIEW Universal CCU HD-22 Part Numbers: 999-6967-000: North America 999-6967-001: International WallVIEW Universal CCU HD-30 Part Numbers: 999-6977-000: North America 999-6977-001: International Use this manual in conjunction with the PowerVIEW HD-22/30 Installation and User Guide.
WallVIEW Universal CCU HD-22/30 Inside Front Cover - Blank Vaddio WallVIEW Universal CCU Cat-5 Version.
WallVIEW Universal CCU HD-22/30 Table of Contents Overview: ................................................................................................................................................................... 4 Intended Use: ......................................................................................................................................................... 4 Important Safeguards: .............................................................................................
WallVIEW Universal CCU HD-22/30 Overview: The WallVIEW Universal CCU system for the PowerVIEW HD-22 and PowerVIEW HD-30 HD Pan/Tilt/Zoom Camera Systems includes the HD-22 or HD-30 PTZ camera, the QuickConnect™ Universal CCU, matching CONCEAL™ camera mount, EZIM CCU Slot Card and accessories (mounting hardware, control adapter).
WallVIEW Universal CCU HD-22/30 Unpacking: Carefully remove the device and all of the parts from the packaging. Unpack and identify the following parts: WallVIEW Universal CCU HD-22, Cat-5 Version Part Number: 999-6967-000, North America One (1) Vaddio PowerVIEW HD-22PTZ Camera (998-6960-000) One (1) Universal CCU Cat-5 for HD-22 or HD-30 with Rack Ears One (1) 36 VDC Switching power supply with power cord for North America One( 1) 2-pin Phoenix-type 5.
WallVIEW Universal CCU HD-22/30 Anatomy of the Universal CCU The Universal CCU interfaces for the PowerVIEW HD-22 and the PowerVIEW HD-30 have very similar control protocols and share the same control keypad. The Universal CCU will automatically sense the camera it is and initialize the firmware for the connected camera. The next section will look at the controls and how they are laid out for easy access.
WallVIEW Universal CCU HD-22/30 Image: Rear Panel Connection and Controls (left to right) Power Supply Input: The Universal CCU uses a 36VDC, 2.78 Amp power supply on a 5.5mm OD x 2.5mm ID coaxial connector. 36 VDC to Camera - RED RJ-45: Power is provided on a Cat-5 cable to EZIM (EZCamera Interface Module) Slot Card. The power is regulated in the camera to 12 VDC RS-232 IN - GREEN RJ-45: RS-232 Input from ProductionVIEW™ console, Precision Camera Controller or other PTZ controller.
WallVIEW Universal CCU HD-22/30 The HD-22 and HD-30 Control Menu Screens The HD-22 and HD-30 have individual firmware that auto loads when the camera is plugged in to the Universal CCU and the CCU is turned on (turn the camera on first). Since most cameras are a bit different, the menus will be slightly different, but the Firmware is the same for the HD-22 and HD-30.
WallVIEW Universal CCU HD-22/30 The Version Menu screen displays the software versions of the Vaddio cameras attached as a convenience to the operator. The versions shown include the zoom module, the motors and the camera. Version Display Menu CAT-5 CCU HD-22 CCU Version V01.0x.ox FPGA Date: XX/XX/20XX VERSION CAM: V01.0X.0X * MOT: V02.0X.0X * Put dip switch #5 UP to access this menu where the firmware versions of the CCU, camera, motors are displayed.
WallVIEW Universal CCU HD-22/30 Installation Basics: The WallVIEW CCU system was specifically designed for installation on a vertical wall surface with Cat-5 cable connectivity for Video, Power and Control signaling (three Cat-5 cables are required). Installation is simplified in that no custom 8-Pin mini-din cables or expensive plenum coax cables are needed and no power outlets are required near the camera bracket.
WallVIEW Universal CCU HD-22/30 Step 3: Secure the Camera To the CONCEAL Wall Mount Bracket After all cables are attached to the camera, place the camera onto the camera mount and insert the two 1/4”-20 screws into the camera through the two-screw holes in the bottom of the mount. Note: Be sure to align each side of the camera evenly to all sides of the CONCEAL Wall Mount Bracket before final tightening of the mounting screws.
WallVIEW Universal CCU HD-22/30 Drawing: Basic System Connectivity Wiring Diagram Example: PowerVIEW HD-22 or HD-30 Rear Panel of HD-22 with EZIM CCU Slot Card installed in the bottom row slot. All Universal CCU camera packages are shipped with the EZIM CCU Slot Card. Please see the manuals for each of the cameras for specifics regarding set-up and switch settings. EZIM Slot Card Three Cat-5 Cables up to 500’ between CCU and Camera POWER VIDEO RS-232 YPbPr 1080i/59.94 HDMI 1080i/59.
WallVIEW Universal CCU HD-22/30 Optimizing System Performance: Optimizing the CCU settings will help achieve maximum performance from the system. Difficult lighting is one of the most challenging problems video system integrators face. The Vaddio CCU will provide the flexibility to fine tune for variables such as cable length, day/night lighting transitions and lighting color temperature.
WallVIEW Universal CCU HD-22/30 General Specifications Universal CCU Interface Connectors Power Connector: 5.5mm OD x 2.
WallVIEW Universal CCU HD-22/30 Warranty Information: (See Vaddio Warranty, Service and Return Policies posted on vaddio.com for complete details): Hardware* Warranty: Two (2) year limited warranty on all parts and labor for Vaddio manufactured products. Vaddio warrants its manufactured products against defects in materials and workmanship for a period of two years from the day of purchase, to the original purchaser, if Vaddio receives notice of such defects during the warranty.
WallVIEW Universal CCU HD-22/30 Compliance and CE Declaration of Conformity - Universal CCU and EZIM CCU Compliance testing was performed to the following regulations: FCC Part 15, Subpart B ICES-003, Issue 4: 2004 European Standard EN 55022 A: October 2007 European Standard EN 55024/A2 January 2003 IEC 60950-1:2005 (Second Edition); Am 1:2009 EN 60950-1:2006+A11:2009+A1:2010+A12:2011 EMC Directive 89/336/EC Class A Class A Class A Class A Safety Safety Class A FCC Part 15 Compliance This
WallVIEW Universal CCU HD-22/30 Appendix 1: Cable Pin-outs for the Quick-Connect CCU System Quick-Connect CCU Pin-out Assignments: Power Connector RJ-45 (Red) Pin # Function Pin - 1 Pin - 2 Pin - 3 Pin - 4 Pin - 5 Pin - 6 Pin - 7 Pin - 8 Power + Power Power + Power Power + Power Power + Power - Pairs 1 1 2 3 3 2 4 4 36 VDC TO CAMERA 12345678 RS-232 IN RJ-45 (Green) Pin # Function Pin - 1 Pin - 2 Pin - 3 Pin - 4 Pin - 5 Pin - 6 Pin - 7 Pin - 8 N/A N/A N/A N/A N/A Digital GND RXD (from TXD of c
WallVIEW Universal CCU HD-22/30 Appendix 1 (continued) EZIM Slot Card Pin-out Assignments Power Connector RJ-45 (Red) Pin # Function Pin - 1 Pin - 2 Pin - 3 Pin - 4 Pin - 5 Pin - 6 Pin - 7 Pin - 8 Power + Power Power + Power Power + Power Power + Power - Pairs 1 1 2 3 3 2 4 4 12345678 POWER Video (HSDS-differential) RJ-45 Pin # Function Pin - 1 Pin - 2 Pin - 3 Pin - 4 Pin - 5 Pin - 6 Pin - 7 Pin - 8 N/A N/A Y+ PB+ PB GND Y GND PR+ PR- Pairs Not Used Not Used 2 3 3 2 4 4 12345678 VIDEO Appe
WallVIEW Universal CCU HD-22/30 Inside Rear Cover – Blank Vaddio WallVIEW Universal CCU Cat-5 Version.
WallVIEW Universal CCU HD-22/30 Toll Free: 800-572-2011 ▪ Phone: 763-971-4400 ▪ FAX: 763-971-4464 www.vaddio.com ©2014 Vaddio - All Rights Reserved. Reproduction in whole or in part without written permission is prohibited. Specifications and pricing are subject to change without notice. Vaddio, Quick-Connect, ProductionVIEW, HSDS, EZIM, WallVIEW, CONCEAL and PowerVIEW are trademarks of Vaddio. Vaddio WallVIEWare Universal Cat-5 Version. owners.
