Installation and User Guide VADDIO™ Quick-Connect™ CCU HE120 Kit for the Panasonic® AW-HE120 (camera not included) Part Numbers without Camera: 998-6127-000: Quick-Connect CCU Kit for the AW-HE120 Camera (camera not included) - North America 998-6127-000: Quick-Connect CCU Kit for the AW-HE120 Camera (camera not included) - International Vaddio WallVIEW™ CCU HE120 with the Panasonic AW-HE120 (camera included) Part Numbers with Camera: 999-6127-000K: WallVIEW CCU HE120 System with Black AW-HE120 (camera in
Quick Connect CCU Kit and WallVIEW Kit for the AW-HE120 Table of Contents Overview: ................................................................................................................................................................... 3 Figure: Front Panel of the Quick-Connect CCU for the AW-HE120 Camera ................................................... 3 Important Safeguards: ....................................................................................................................
Quick Connect CCU Kit and WallVIEW Kit for the AW-HE120 Overview: The Vaddio Quick-Connect CCU system for the AW-HE120 camera allows the user to control the color output of the camera’s image sensor through both Red and Blue Gain controls, Detail, Chroma, Gamma, Total Pedestal, as well as Iris and Gain levels, to provide a higher quality image. In addition, there are also Red and Blue Pedestal parameters.
Quick Connect CCU Kit and WallVIEW Kit for the AW-HE120 Information: For RS-232 control information, please see the full-length Technical Manual for the Panasonic AW-HE120. This manual can be found either on the Panasonic or the Vaddio website. Unpacking: Carefully remove the device(s) and all parts from the packaging. Please do not toss the packaging yet, just set it aside where it won’t be in the way.
Quick Connect CCU Kit and WallVIEW Kit for the AW-HE120 Anatomy of the CCU Controlled Camera System Image: The Quick-Connect CCU Front Panel Controls (left to right) Tally Light: The blue LED tally light on the front panel is tied to the tally contacts on the rear panel allowing the user to easily track which camera interface is being used in a multi-camera system by supplying a simple contact closure (i.e. from ProductionVIEW Super Joystick or ProductionVIEW HD).
Quick Connect CCU Kit and WallVIEW Kit for the AW-HE120 Shift to Bottom Row Controls: Red and Blue Pedestal: These controls allow the Red and Blue Pedestal to be adjusted (see Panasonic manual). DRS: Dynamic Range Stretch optimizes images that have a wide contrast range. When dark, bright and intermediate areas are all in the same image or rapidly changing lighting changes occur frequently, DRS estimates a gamma curve and knee slope for each image pixel to minimize blocked shadows and blown highlights.
Quick Connect CCU Kit and WallVIEW Kit for the AW-HE120 Connector Labels and Supported Video Signals Y/Y: Y of YPbPr - or - Y (luminance) of Y/C on BNC-F connector PB/C: PB of YPbPr - or - C (chrominance) of Y/C on BNC-F connector PR: PR of YPbPr only on BNC-F connector COMP: Composite (CVBS) Video on BNC-F connector Video RJ-45: This RJ-45 receives the camera’s four (4) differential video signals from the EZIM CCU to the Quick-Connect CCU on Video Cat-5 cable.
Quick Connect CCU Kit and WallVIEW Kit for the AW-HE120 Please do not use “pass-thru” type RJ-45 connectors. The Vaddio Cat-5 wiring standard uses pins 7 and 8 on both the video and the control Cat-5e cables. The pass-through connectors have proven to provide insufficient connectivity for these important signals. They are “ok” for voice and data, but not for video and control.
Quick Connect CCU Kit and WallVIEW Kit for the AW-HE120 Step 3: Take the Wall Mount, with the EZIM CCU and break out cable installed, and place it against the drywall anchors or 3-gang wall box, making sure to pull the three Cat-5 cables through the oval pass-through hole. Finger-tighten the screws to the mount and confirm that the base is level. Tighten the screws firmly. If the bracket is to be mounted on a 3-gang wall box, use the screws supplied with the electrical box.
Quick Connect CCU Kit and WallVIEW Kit for the AW-HE120 Drawing: Basic System Connectivity Wiring Diagram Example: System Configuration Notes: The Quick-Connect CCU System uses a Cat-5 (all 4-pairs) for power to ensure the motors receive the required current to operate properly. The Video Cat-5 cable uses all four pairs for video (YPbPr & CVBS). The RS-232 Cat-5 provides communication to the camera for CCU, PTZ control and G/L (where applicable) to the camera. These Cat.
Quick Connect CCU Kit and WallVIEW Kit for the AW-HE120 Adjust the Y Gain Settings*: Enable both Auto Iris and Auto White Balance prior to adjustment. Make sure the distance adjustment is set at its lowest setting. Adjust the trim pot on the back of the CCU counterclockwise until picture fades or drops out (cable length dependent). Adjust clockwise just past the setting where picture is restored. Leave the distance adjustment** at its lowest setting unless recommended by Vaddio technical support.
Quick Connect CCU Kit and WallVIEW Kit for the AW-HE120 Warranty Information: (See Vaddio Warranty, Service and Return Policies posted on vaddio.com for complete details): Hardware* Warranty: One year limited warranty on all parts. Vaddio warrants this product against defects in materials and workmanship for a period of one year from the day of purchase from Vaddio.
Quick Connect CCU Kit and WallVIEW Kit for the AW-HE120 Compliance and CE Declaration of Conformity - Quick-Connect CCU and EZIM CCU Compliance testing was performed to the following regulations: FCC Part 15, Subpart B ICES-003, Issue 4: 2004 European Standard EN 55022 A: 1998 + A1: 2000 European Standard EN 55024: 1998 + Amendments A1: 2001 + A2: 2002 EMC Directive 89/336/EC Class A Class A Class A Class A Class A FCC Part 15 Compliance This equipment has been tested and found to comply with
Quick Connect CCU Kit and WallVIEW Kit for the AW-HE120 Appendix 1: Cable Pin-outs for the Quick-Connect CCU System Quick-Connect CCU Pin-out Assignments: Power Connector RJ-45 Pin Signal 1) Power + 2) Power 3) Power + 4) Power 5) Power + 6) Power 7) Power + 8) Power RS-232 IN Connector RJ-45 Pin Signal - RS-232 1) Not Used 2) Not Used 3) Not Used 4) Not Used 5) Not Used 6) GND 7) RXD (from TXD) 8) TXD (to RXD) RS-232 / G/L OUT Connector RJ-45 Pin Signal - RS-232 1) Not Used 2) Not Used 3) Not Used 4) G/L
Quick Connect CCU Kit and WallVIEW Kit for the AW-HE120 Appendix 1 (continued) EZIM CCU Pin-out Assignments Power Connector RJ-45 Pin Signal 1) Power + 2) Power 3) Power + 4) Power 5) Power + 6) Power 7) Power + 8) Power - EZIM CCU RS-232 IN/ VIDEO G/L IN 12345678 Genlock Gain Adjustment: Genlock Gain is set at the factory to the 3 o’clock position, which provides standard blackburst level. Adjust the gain level up or down if required to synchronize the camera to other devices.
Quick Connect CCU Kit and WallVIEW Kit for the AW-HE120 Toll Free: 800-572-2011 ▪ Phone: 763-971-4400 ▪ FAX: 763-971-4464 www.vaddio.com ©2012 Vaddio - All Rights Reserved. Reproduction in whole or in part without written permission is prohibited. Specifications and pricing are subject to change without notice. Vaddio, Quick-Connect, HSDS, EZCamera, ProductionVIEW, EZIM and PowerRite are trademarks of Vaddio. All other trademarks are property of their respective owners. Document 342-0507 Rev.
