INSTALLATION AND USERS GUIDE WALLVIEW HD-18 DVI/HDMI With Quick-Connect™ DVI/HDMI - SR with HSDS™ and the CONCEAL Wall Mounting System for the Vaddio™ HD-18 Robotic Pan/Tilt/Zoom Camera Quick-Connect DVI/HDMI - SR Interface Used in the Following Packages 998-1105-018: Quick-Connect DVI/HDMI - SR Interface (Interface Box Only - Without Peripherals) 998-6906-000: Quick-Connect DVI/HDMI - SR Interface Kit - North America - (Camera Not Included) 998-6906-001: Quick-Connect DVI/HDMI - SR Interface Kit - Interna
WallVIEW HD-18 DVI/HDMI Inside Front Cover - Blank ©2011 Vaddio - All Rights Reserved. WallVIEW HD19 DVI/HDMI, Document Number 342-0045 Rev.
WallVIEW HD-18 DVI/HDMI Quick-Connect DVI/HDMI - SR Interface Overview: The Vaddio Quick-Connect DVI/HDMI SR Interface was designed and built specifically to advance the Vaddio HD-18 camera into a wide variety of digital video and extended control applications.
WallVIEW HD-18 DVI/HDMI UNPACKING: System Configurations - Bill of Materials: Because the Quick-Connect DVI/HDMI - SR Interface is available in several packages, please review the bill of materials upon receipt to ensure that all the parts are present and accounted for. The ferrite cylinders may come in handy when this product is used in a large rack full of equipment in order to eliminate any possible interference with other audio/video products.
WallVIEW HD-18 DVI/HDMI Unpacking System Configurations (continued) WallVIEW DVI/HDMI HD-18 System, Part Number 999-6906-001 International - Black Camera Kit Part Number 999-6906-001W International - White Camera Kit One (1) HD-18 PTZ Camera 999-6900-001 (Black) or 999-6900-001W (White) One (1) Quick-Connect DVI/HDMI Interface Box One (1) 24VDC, 2Amp Switching Power One (1) AC Cord Set for Euro and One (1) AC Cord Set for UK One (1) Laird Technologies 28A2432-0A2 Clamp-on Ferrite
WallVIEW HD-18 DVI/HDMI Quick-Connect DVI/HDMI - SR Interface Key Features: Integrated Design for use with the HD-18: The Quick-Connect DVI/HDMI and the HD-18 both use high speed differential signaling (HSDS) for transmission of high definition video (up to 1080p)/60 and IR signals over Category 5 cabling. Video, Power and Control is conveyed using only two Category 5 cables.
WallVIEW HD-18 DVI/HDMI System Connectivity Example 2: System connectivity of Vaddio HD-18 Cameras and Quick-Connect DVI/HDMI - SR Interfaces Configured with Single Control Port Codec with Daisy Chain Control Emulation (DCCE). Vaddio HD-18 HD Camera Systems Power to Camera HD Video from Camera - Cat. 5 Power to Camera HD Video from Camera - Cat. 5 Codec IR Remote: Forwarded through Main Camera for Codec Control Two (2) - Cat 5e Cables - up to 100’ (30.
WallVIEW HD-18 DVI/HDMI Mounting and Installation Instructions for the CONCEAL Wall Mounting System: Step 1: Determine Camera Mount Location Note: When locating the camera, consider viewing angles, lighting conditions, possible line of site obstructions and check for in-wall obstructions where the camera is to be mounted. Pick a mounting location to optimize the performance of the camera. The 2 (two) Cat-5e cables should feed-through a 1” (25.
WallVIEW HD-18 DVI/HDMI Step 3: SECURE THE CAMERA TO THE CONCEAL WALL MOUNT BRACKET: After all cables are attached to the camera, place the camera onto the camera mount and insert the two(1/4”-20) screws into the camera through the two-screw holes in the bottom of the mount. Note: Be sure to align each side of the camera evenly to all sides of the CONCEAL Wall Mount Bracket before final tightening of the mounting screws (see Fig. 2). Fig.
WallVIEW HD-18 DVI/HDMI RS-232 Cabling For RS-232, use a standard CAT-5 cable (568B termination for RJ-45 connectors) from the RS-232 port on the back of a Vaddio ProductionVIEW camera controller or switcher. If the camera will be connected to a third-party control system (such as AMX® or Crestron®), a DB-9 to RJ-45 adapter cable is supplied with the camera for RS-232.
WallVIEW HD-18 DVI/HDMI Compliance and CE Declaration of Conformity - ClearVIEW HD-19 Compliance testing was performed to the following regulations: FCC Part 15, Subpart B ICES-003, Issue 4: 2004 EN 55022 A: 2006 + A1: 2007(CISPR 22:2005/A1:2005) AS/NZS CISPR 22: 2009 + A1: 2010 VCCI V-3/2010.
WallVIEW HD-18 DVI/HDMI Compliance and CE Declaration of Conformity FCC Part 15 Compliance This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15, Subpart B, of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
WallVIEW HD-18 DVI/HDMI Hardware* Warranty - One year limited warranty on all parts. Vaddio warrants this product against defects in materials and workmanship for a period of one year from the day of purchase from Vaddio. If Vaddio receives notice of such defects during the warranty period, they will, at their option, repair or replace products that prove to be defective.
WallVIEW HD-18 DVI/HDMI General Specifications: Quick-Connect DVI/HDMI - SR Interface Part Numbers Connectors Video Resolution Cat.
WallVIEW HD-18 DVI/HDMI Inside Back Cover - Blank ©2011 Vaddio - All Rights Reserved. WallVIEW HD19 DVI/HDMI, Document Number 342-0045 Rev.
WallVIEW HD-18 DVI/HDMI 9433 Science Center Drive, Minneapolis, MN 55428 Toll Free: 800-572-2011 ▪ Phone: 763-971-4400 ▪ FAX: 763-971-4464 www.vaddio.com ©2012 Vaddio - All Rights Reserved. Reproduction in whole or in part without written permission is prohibited. Specifications and pricing are subject to change without notice. Vaddio, Quick-Connect, DCCE, HSDS, ProductionVIEW, PreVIEW, AutoPresenter, ControlVIEW, ProductionVIEW, EZCamera and PowerRite are trademarks of Vaddio.
