Installation and User Guide Vaddio™ WallVIEW™ PRO H900 Featuring the Quick-Connect PRO, EZIM and Sony® BRC-H900 Part Numbers: 999-6895-000: WallVIEW PRO H900 System with the Sony BRC-H900 (camera included) - North America 999-6895-001: WallVIEW PRO H900 System with the Sony BRC-H900 (camera included) - International © 2013 Vaddio - All Rights Reserved. Prices and specifications are subject to change without prior notice.
Quick-Connect PRO for the BRC-H900 Camera Inside Front Cover - Blank © 2013 Vaddio - All Rights Reserved.
Quick-Connect PRO for the BRC-H900 Camera Contents Overview: ................................................................................................................................................................... 4 Important Safeguards: ........................................................................................................................................... 4 Intended Use ...........................................................................................................
Quick-Connect PRO for the BRC-H900 Camera Overview: Vaddio WallVIEW PRO BRC-H900 is built and adapted for use with the Sony BRC-H900 3-CMOS HD pan/tilt/zoom robotic camera. This system was designed for an easier cable extension installation and integration where the camera must be located a long distance away from the head-end processors and switchers. The Quick-Connect PRO uses HSDS™ (high speed differential signaling), which is a highly accurate, long distance, active video transmission system.
Quick-Connect PRO for the BRC-H900 Camera Information: For RS-232 control information, please see the full-length Technical Manual for the BRC-H900. This manual can be found either on the Sony or the Vaddio website. Unpacking 998-6895-000: WallVIEW PRO H900 - North America Carefully remove the device(s) and all parts from the packaging. Please do not toss the packaging yet, just set it aside where it won’t be in the way.
Quick-Connect PRO for the BRC-H900 Camera Anatomy of the Quick-Connect PRO System Interface Image: Quick-Connect PRO Front Panel Indicator (left to right) Power Light: Illuminates when the power supply is plugged in the back of the Quick-Connect This concludes our tour of the front panel. Image: Quick-Connect PRO Rear Panel Connectors and Controls (left to right) Power Supply Input: The Quick-Connect PRO uses a 36VDC, 2.78 Amp power supply on a 5.5mm OD x 2.5mm ID connector.
Quick-Connect PRO for the BRC-H900 Camera Image: EZIM Top Panel (left to right) and ISO View of EZIM (About the size of a deck of cards) POWER RJ-45: The EZIM CCU receives 36 VDC on one Cat-5 cable (all 4-pair) from the CCU. Be sure to mark the Power Cat-5 and avoid plugging it into a place it doesn’t belong. EZIM: Top Connector Panel and 25-pin side connector shown RS-232 IN: Connect this RJ-45 with a Cat-5 cable to the RS-232 out of the RS-422 to RS-232 adapter.
Quick-Connect PRO for the BRC-H900 Camera Step By Step Mounting Instructions: Step 1: After determining the optimum location of the camera system, mark the locations for the four screw holes and cable pass-thru (vertical oval). Install the drywall mounts and cut the hole for the cable pass-thru. At this point, do not install the Wall Mount. Image: Huge-Heavy Duty Wall Mount The wall mount may be mounted directly to a 3-gang wall box or to drywall with the appropriate wall anchors.
Quick-Connect PRO for the BRC-H900 Camera Step 3: Take the Wall Mount, with the EZIM and break out cable installed, and place it against the drywall anchors or 3-gang wall box, making sure to pull the three Cat-5 cables through the oval pass-through hole. Finger-tighten the screws to the mount and confirm that the base is level. Tighten the screws firmly. If the bracket is to be mounted on a 3-gang wall box, use the screws supplied with the electrical box.
Quick-Connect PRO for the BRC-H900 Camera Completing the Installation: Connect the Vaddio 36 VDC power supply to the DC Plug on the back of the Quick-Connect and the AC side to an AC outlet. Power will travel down the Power Cat-5 cable to the EZIM, powering the camera. The camera will “Home” to a centered position ready for control information from the IR remote control or RS-232 camera controller of the integrators’ choice.
Quick-Connect PRO for the BRC-H900 Camera FCC, ICES-003 Compliance and CE Declaration of Conformity Quick-Connect PRO Series Interface and EZIM Products FCC Part 15 Compliance This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
Quick-Connect PRO for the BRC-H900 Camera Warranty Information: (See Vaddio Warranty, Service and Return Policies posted on vaddio.com for complete details): Hardware* Warranty: Two (2) year limited warranty on all parts and labor for Vaddio manufactured products. Vaddio warrants its manufactured products against defects in materials and workmanship for a period of two years from the day of purchase, to the original purchaser, if Vaddio receives notice of such defects during the warranty.
Quick-Connect PRO for the BRC-H900 Camera Appendix 1: Cable Pin-outs for the WallVIEW PRO Systems EZCamera Interface Module Pin-outs Power Connector Pin Signal 1 Power + 2 Power 3 Power + 4 Power 5 Power + 6 Power 7 Power + 8 Power - Same HD Pin-outs as below RS-232 IN Connector Pin Signal 1) Unused 2) Unused 3) Unused 4) Unused 5) Unused 6) Unused 7) Unused 8) Unused 12345678 RS-232 OUT Connector Pin Signal 1) Unused 2) Unused 3) Unused 4) Unused 5) Unused 6) Unused 7) Unused 8) Unused RS-232 Note: T
Quick-Connect PRO for the BRC-H900 Camera EZCamera Interface Module Pin-outs (continued) DB-25 Connector Pins Signal 1 GND Out 14 RXD Out 2 TXD Out 15 DTR Out 3 DSR Out 16 GND IN 4 TXD IN 17 RXD IN 5 DTR IN 18 DSR IN 6 IR 19 GND 7 GND 20 CVBS/PR 8 GND 21 C/PB 9 GND 22 Y/Y 10 GND 23 GND 11 GND 24 12V 12 12V 25 12V 13 12V © 2013 Vaddio - All Rights Reserved.
Quick-Connect PRO for the BRC-H900 Camera Inside Back Cover - Blank © 2013 Vaddio - All Rights Reserved.
Quick-Connect PRO for the BRC-H900 Camera Toll Free: 800-572-2011 ▪ Phone: 763-971-4400 ▪ FAX: 763-971-4464 www.vaddio.com ©2013 Vaddio - All Rights Reserved. Reproduction in whole or in part without written permission is prohibited. Specifications and pricing are subject to change without notice. Vaddio, Quick-Connect, HSDS, EZCamera, ProductionVIEW and EZIM are trademarks of Vaddio. All other trademarks are © property of their- respective owners. Document Rev. A Rev A 2013 Vaddio All Rights Reserved.
