Installation guide

SkyView System Installation Guide - Revision R xi
Revision
Revision Date
Description
Sensor definition files do not match between SkyView displays (Page 7-60)
Transponder HEX CODE is not set (Page 11-15)
 Wide field of view for Synthetic Vision (Page 3-12)
 Vne can now be expressed as TAS as well as IAS (Page 5-8, 10-20)
 MW Fly AEROPOWER engines supported in SV-EMS-221 (Page 7-1)
 AP Disconnect/CWS Switch and External LEVEL Button status is checked at boot.
(Page 10-13, 10-14)
 AP Disconnect/CWS Switch is checked upon entering SERVO CALIBRATION (Page 10-
16)
 ADS-B traffic display enabled with non-Dynon ADS-B OUT devices (Page 14-1)
 Independent volume control for Angle of Attack (Page 15-7)
Documentation added:
 Added explanation that SkyView can be powered on during engine start (Page 2-5)
 Recommendation to install Panel Mount USB cable with each SkyView display (Page
2-6)
 Serial port connection and configuration information for Emergency Location
Transmitter (ELT) (Page 4-20)
 External Dim Control Connections (Page 4-20)
 SV-ADAHRS-200/201 must be installed level or the Slip/Skid Ball will not be centered
(Page 5-3)
 Caution about applying too much torque when installing SV-BAT-320 (Page 9-2)
 Addition of capacitor to servo to eliminate Intercom noise (Page 10-12, 10-13)
 Pin descriptions, added wiring diagram for SV-AP-PANEL Trim Controller installation
(Chapter 19)
 As of v11.0, SkyView does not have “Auto Trim” capability (Page 19-3)
 Alert Data Log (Page 26-2)
Documentation improved:
 Getting Started (Pages 1-2 through 1-4)
 SkyView System Power Specifications (Table 2, Page 2-2)
 Corrected SV-XPNDR-261/262 dimensions (Page 2-3)
 Recommendation to not use stainless steel hardware for installing SV-ADAHRS-
200/201, added recommendation to use Brass hardware (Page 2-8, Page 5-3)
 Explanation of Dynon Diagnostic File (Page 3-10 and Page 3-16)
 Updated screen shots throughout SV-D700 / SV-D1000 / SV-D1000T Installation and
Configuration (Chapter 4)
 Moved configuration information for Garmin GTX 330ES to Traffic Devices section
(Page 4-14)
 VAL NAV 2000 – frequency cannot be displayed on top bar (Page 4-17)
 Updated SV-ADAHRS-200/201 Magnetic Calibration Procedure (Page 5-5)
 Differences between SV-EMS-220 and SV-EMS-221 (Page 7-1)
 Rotax oil pressure sensor connector charge (Page 7-41, 7-42)
 Oil temperature sensor section, updated crush washer installation instructions.
(Page 7-42)
 Rotax 914 Differential Fuel Pressure Sensor UMA N1EU07D guidance improved
(Page -7-44, 7-45)
 Suppress units displayed on sensor widgets (Page 7-63)
 Effect of setting ALLOW AUTO SWITCH to YES (LABEL 100P) for 430/530 (Page 12-7)
and GTN-series (12-9)
 Setup for transponders other than SV-XPNDR-261/262 with ADS-B OUT for receiving
ADS-B Traffic information with SV-ADSB-470 (Page 14-1)
 Check for blockage of AOA / Pitot lines prior to installation (Page 15-10)
 SV-COM-C25 Post Installation Checks, Continued Airworthiness and Maintenance
(Page 16-8, 16-9)
 Homemade Wire Harness Considerations (Page 21-2 through 21-4)
 MAP button no longer available (Page 21-11)
 Kavlico pressure sensors information (Appendix G)
Table 1–SkyView System Installation Guide Revision History