User guide

ManualsBrandsValco Baby ManualsFor HomeTri Mode Twin SE

Thank you for purchasing a quality Valco Baby product. Please read and follow the instructions outlined in this

guide carefully. Familiarise yourself with the construction and safety features; be sure that you understand all

the warnings and safety guidelines before use.

Important: Please read the following instructions carefully before assembling this product. Retain this

guide in a safe place for future reference.

PRODUCT REFERENCE GUIDE

Due to our policy of continuous product

development, this product is constantly

evolving. It is possible that some

features or procedures outlined here

have changed since this document

was written. If you are unsure of any

procedure shown here, please contact

us via the web at info@valcobaby.com

to obtain the most up to date information

before use. Include the batch number,

which can be found on a sticker on the

frame.

All pictures and diagrams herein are

provided for illustration purposes only.

Actual product, color or fabric may vary.

Valco Baby reserves the right to modify

or alter any specication or colour

without notice or obligation to modify any

product previously purchased

FURTHER INFORMATION

In Australia/New Zealand

www.valco.com.au

www.valco.co.nz

In North America only

www.valcobaby.com

1800 610 7850

TRIMODE

TWIN EX

STOLLER

Summary of content (8 pages)

PAGE 1
TRIMODE TWIN EX STOLLER PRODUCT REFERENCE GUIDE Thank you for purchasing a quality Valco Baby product. Please read and follow the instructions outlined in this guide carefully. Familiarise yourself with the construction and safety features; be sure that you understand all the warnings and safety guidelines before use. Important: Please read the following instructions carefully before assembling this product. Retain this guide in a safe place for future reference.
PAGE 2
A Opening the stroller chassis FIGURE A 1. Lay the stroller flat on the floor and carefully cut the cable tie which holds the frame. To unfold the chassis, locate the rear legs. NOTE: The rear centre leg is highlighted in red. 2. Holding the rear centre leg, lift the stroller upwards. Pull the centre leg outwards as far as it can go. FIGURE B B 3. Lift the handlebar upward towards you until the stroller is in a vertical position. 4.
PAGE 3
FIGURE E E 7. Press the axle button and insert the protruding long axle into the opening on the stroller frame beneath the brake. Release the axle button when wheel is in place to secure. NOTE: Ensure that the brake pedal is fully retracted, so that the brake pin (highlighted in red) does not obstruct the wheel cog from fully engaging the housing. 8. Repeat the procedure for the other side. TEST that each wheel is securely engaged by pulling on it. 9.
PAGE 4
b Installing the EXpanda hoods H a FIGURE H 18. Identify left and right side hoods by determining that the sliding housing (Image K) sits on the SIDE (a) of the frame, and the puzzle housing (b) (Image J) rests on the centre (c) of the stroller. c I d FIGURE J Turn your stroller around to the Front: [SEE IMAGE H (c)] 20. Insert the hood section (e) into the corresponding housing (f) in the centre of the seat. J e f FIGURE I Turn your stroller around to the back: 19.
PAGE 5
M N USING THE EXPANDA HOOD FIGURE M The Expanda hood unzips, increasing the size of your standard hood, to give greater coverage and protection from the sun and weather for your child. To open the Expanda Hood: 26. Locate the zip in the center of the Expanda Hood and unzip completely 27. Gently pull the Expanda Hood forward until it is reaches its full extension. To close the Expanda Hood: 28. Gently push the Expanda Hood back, allowing the middle section to fold in on itself. 29.
PAGE 6
Q using your brakes FIGURE Q 36. To engage: Press down on the centre pedal until the brake pins engage in the nylon brake cogs in the wheel hub. IMPORTANT: Always check that the brake has engaged before use, if not you may need to move the stroller forward or back slightly until it locks into place. 37. To disengage, lift the centre pedal upward till it locks in the upright position. Folding the stroller FIGURE R R 44 38. Fold the hood back up against the handle. 39.
PAGE 7
U USING THE HARNESS Your child MUST always be harnessed while in the stroller. FIGURE U TO OPEN YOUR HARNESS: 49. Push down on both buckle prongs and hold. 50. Simultaneously press the release button in the centre of the buckle. 51. Lift the buckles from the buckle housing. THIS PROCESS MAY BE DIFFICULT AS YOUR BUCKLE SYSTEM HAS BEEN DESIGNED TO MEET VERY STRINGENT SAFETY STANDARDS AND ENSURE THAT A CHILD CANNOT RELEASE THE HARNESS UNAIDED. V TO SECURE YOUR CHILD IN THE HARNESS: FIGURE V 52.
PAGE 8
WARNING • FOLLOW THE MANUFACTURER’S INSTRUCTIONS. • PUT ON ALL THE BRAKES WHENEVER YOU PARK THE PRAM/STROLLER. • DO NOT LEAVE CHILDREN UNATTENDED. • DO NOT CARRY EXTRA CHILDREN OR BAGS ON THIS PRAM/STROLLER. • MAKE SURE CHILDREN ARE CLEAR OF ANY MOVING PARTS IF YOU ADJUST THE PRAM/STROLLER. OTHERWISE THEY MAY BE INJURED. Remember, your child’s safety is your responsibility... • NEVER USE ON stairs or ESCALATORS. • Always use the tether strap when the stroller is in use.