SERIES Product Reference Guide Read and follow the instructions contained within carefully before use. Retain this guide in a safe and easily accessible place for future reference. Drawings, pictures and specifications contained in this manual are for illustration purposes only – actual product may vary. VALCO BABY reserves the right to alter any specification(s), colour or features without prior notice or incurring any obligation to similarly alter products previously purchased.
Thank you for purchasing a quality VALCO product. Due to our policy of continuous product development, this product is constantly evolving. It is possible that some features or procedures outlined here have changed since this document was written. If you are unsure of any procedure outlined here please contact the store from which you purchased it to obtain the most up to date information, or contact us via the internet. See relevant web contact addresses on the back page.
Basic Components 1 x Chassis installed with Seat Liner and Basket 1 x Rear Axle-Brake System 2 x Rear Wheels 2 x Rear Axle Pins (SQR Axles) 2 x Front Forks & Front Wheels 2 x Hoods (Left & Right Side) 1 x Twin Runabout Front Bar 4 x Nylon Housing Bracket Plugs
Stroller Assembly Remove the stroller from the carton and dispose of all packaging immediately. The front wheel forks, rear wheels, front bar, and hood all need to be installed prior to use. Installing/Removing the rear axle-brake system 1. Take the rear axle with the longer part of the centre pedal facing to the rear. 2. Identify the locking pins (A) located on both rear frame legs. 3. Align the locking pins (A) with the corresponding notches in the brake housing (B). 4.
Unfold the chassis: 1. Holding the rear centre leg, lift the stroller upwards. 2. Pull the centre leg outwards as far as it can go. 3. Lift the handle upward and back to a vertical position. 4. Secure the handle by swinging the locking clamps (located on both sides of the frame) and fully engaging them tightly onto the frame. 5. Press down on the basket frame locking hinge with your hand or foot. IMPORTANT WARNING: Always test that all latches are securely engaged before use.
2. Pressing the axle button, insert the protruding long axle into the opening in the axle tube. (Refer to ‘Using your brakes’) NOTE: Ensure that the brake pedal is fully retracted, so that the brake pin (highlighted in red) does not obstruct the wheel cog from fully engaging the housing. 3. Repeat the procedure for the other side. TEST that each wheel is securely engaged by pulling on it. 4.
The unique TRI-MODE™ swivel system is as flexible as it is functional over a variety of terrains and uses. Installing/Removing your hoods Identify left right side hoods, where each centre section (A) is in the middle of the pram. 1. Insert hood section (A) into the corresponding housing in the centre of the seat (B). 1. LOCK: This position is best for use on extremely rough or soft terrain such as sand etc which inhibit wheel swivel. To lock your wheel, rotate the dial to the “LOCK” position.
4. Slide the hood housing downward, engaging the track in the channel, continue sliding downward until the rivet outside (D) is fully engaged in the housing. 5. Repeat the procedure for the other hood. 6. Secure each hood to the rear of the frame with Velcro straps at the centre (E), and both sides of the hood (F). NOTE: Before using your stroller, be sure to attach the tether straps around the stroller frame by feeding the strap through the slit in the steel buckle.
Installing/Removing your front bar 1. Remove the plugs from the nylon housing at either side of the stroller frame by pressing each inner “release button” and pulling the plug upward. NOTE: DO NOT remove the plugs in the centre between both seats. Be sure to store the removed plugs in a secure place as they MUST be used whenever nothing is engaged in the front bar housing to prevent finger entrapment. 2. Insert the bar ends into the nylon housing located on either side of the frame.
Folding/Opening your stroller 1. Fold the hood back up against the handle. 2. Release the locking clamps at either side of the stroller. 3. Simultaneously lift the secondary safety catch (located at the left hand side of the stroller while standing behind) and swing the handle forward. 4. Holding the rear legs at both sides, press down with your foot on the rear basket tube. This will disengage the basket frame locking hinges. 5.
9. With your foot on the inside of the rear wheels, stopping them from moving, lift the handle upwards. (This will begin to move the rear wheels away from the 10. Press down on the basket frame locking hinges to lock the frame in the open position. 11. Secure the handle to the frame by engaging the locking clamps on both sides. IMPORTANT WARNING: Always test that all axles, wheels, front bar, hinges and locks are securely engaged before use.
Your Twin Runabout hoods are fitted with zips to which attaches our unique silver insect mesh. 1. Align the centre of the mesh above both expanded hoods, ensuring that the zip ends are in the correct position as shown in (A). 2. Run the zips all the way across each hood arches for the mesh to fully cover the front end. 3. Secure the front edge of the insect mesh by fastening the studs under the footplate as shown in (B). 4.
AIRGO™ SYSTEM Your Twin Runabout has been designed to maximise air flow within the stroller by way of our exclusive Airgo™ system. This unique system combines a special breathable seat fabric, with our unique hood skirt. This incorporates a zip-off bag which reveals a mesh air vent, which allows additional air flow for your child’s comfort. The bag can be hung from the stroller handles. Using your harness Your Runabout stroller is fitted with our unique new multi point safety harness system.
OPTIONAL/ADDITIONAL ACCESSORIES UV Protective Insect Net Our unique insect net zips directly in to the inside of your RUNABOUT Tri Mode hood. In addition to keeping baby cool, comfortable and safe from insects, it also blocks up to a massive 80%* of the sun’s harmful UV rays. (* tested to Australian Standard 4399) Toddlerseat Available in versions for both Single and Twin Runabout models, the optional toddlerseat sits firmly inside the chassis.
OPTIONAL ACCESSORIES The VALCO HITCHHIKER is a boon to any parent with a child who is old enough to walk but young enough to need to rest along the way. Made of high quality and extremely sturdy materials (maximum weight 30 kg’s / 66 lb’s), the HITCHHIKER is easily adjustable for height, width and distance from the stroller which makes it fit most brands, makes and models of strollers.
WARNINGS Your child’s safety is your responsibility ……… Be sure to check that all clamps and buckles are securely fixed and in place before use. Check all parts for breakage or fatigue before use. Discontinue immediately if any part is found to be damaged or broken. The maximum weight of the child for which this stroller is intended is 22 kg’s (48 lbs) each child. The maximum height of the child for which this stroller is intended is 106 cm (42 in).