Specifications

ManualsBrandsValcom ManualsPagerValcom V-9908

9479801

Issue 1

V-9908 MESSAGE/PAGE PANEL

Introduction

These instructions contain the specifications and

guidelines necessary to install, operate, and

maintain the V-9908, Message/Page Panel.

The V-9908 Message/Page Panel is used with

Valcom Supervised Distributed Amplified One-Way

Paging Speakers and Horns providing full system

supervision.

The V-9908 provides a handheld push-to-talk

microphone for live pages and storage for eight

messages. The unit provides full system supervision

including the microphone and speaker line.

Applications

• Valcom Supervised Distributed Amplified

One-Way Paging Systems.

• Refer to Figure 1 for a block diagram of a typical

installation.

Features

• Dynamic noise canceling handheld microphone

for live page

• Provides up to 8 minutes of high quality digital

recording

• Stores and plays up to 8 messages

• PC Programmable

• Message panel fully supervised

• Provides speaker line supervision

• Provides microphone supervision

• Provides DC power supervision

• Allows remote message activation

• Visual and audible system trouble indication

• Audible signal cancel button

• Power "ON" indicator

• Mounts in most 4 gang deep electrical box

Dimensions

• 5"W x 4.25"H x 2”D

(12.7cm W x 10.8cm D x 5.08cm H)

• 4 lbs. (1.5Kg)

Specifications

Power Requirements

• Operating Voltage 22 – 26VDC

• Current 100mA

Microphone Input

Input Impedance: >5000 Ohms

Input sensitivity: 1kHz 1 millivolt for -12dBm

output (output terminated with 100 Ohms)

Audio

Frequency Response:

Mic – Output: 150Hz – 7,000Hz

Frequency Response:

Stored Messages – Output: 150Hz – 3,500Hz

Input Sensitivity (mic): 1kHz 1 millivolt for -12dBm

output (output terminated with 100 Ohms)

Signal to Noise (Idle mode, Ref -12dBm): >70dB

Signal to Noise (Mic active, Ref -12dBm) >50dB

Distortion (Mic – Output): < 1% THD at -12dBm

Output Impedance: < 25 Ohms

Nominal output level: -12dBm (Ref 600 Ohms)

Maximum output level: 0dBm (before clipping)

System Supervision

Main Audio Channel: 30Hz tone (inaudible)

Microphone: 1kHz tone supervises the preamp,

cable and element

Microphone Switch: DC loop with 4.7K Ohm resistor

Audio Output: DC loop terminated with a 4.7K Ohm

1/4W resistor

Voice Storage Memory: Fixed segment memory

monitoring

Main Power: 9VDC battery provides redundant

supervision power

Battery: Low voltage monitoring

All system faults are indicated by both an audible

and visual alarm. The audible

alarm may be

silenced, however, the visual indicator will continue

to illuminate until the fault is removed.

Summary of content (6 pages)

PAGE 1
Issue 1 V-9908 MESSAGE/PAGE PANEL Introduction These instructions contain the specifications and guidelines necessary to install, operate, and maintain the V-9908, Message/Page Panel. The V-9908 Message/Page Panel is used with Valcom Supervised Distributed Amplified One-Way Paging Speakers and Horns providing full system supervision. The V-9908 provides a handheld push-to-talk microphone for live pages and storage for eight messages.
PAGE 2
provides all editing and message processing (AGC, response shaping, wave file conversions, etc.). The final format is standard 8 bit uLaw at 8kHz compressed format. User Controls (Figure 1) • • • • Push-to-Talk Microphone Pushbuttons to activate pre-recorded messages Pushbutton to cancel message play Pushbutton to cancel wire fault alarm Although it is possible to upload and download during system operation, it is recommended to perform this function when the system is not in use.
PAGE 3
• Using an RJ-45 connector, connect speaker audio (Tip and Ring) and speaker power to board mounted connector as shown on connecting diagram. • All connections should be made to the mixer and double-checked prior to connecting DC power. LED D11 Audio loop back fault (ON = Fault in Mic.
PAGE 4
Noise Canceling Handheld Push to Talk Microphone Message Cancel Button Eight (8) Message Play Buttons Eight (8) Message Play Indicators Message Label Window Fault Audible Cancel Button Figure 1: User Control Locations System Fault Indicator Message Activate Contact Closure Inputs Serial Programming Input 9 V Alkaline Battery Output Connections RJ-45 Connection Detail 24VDC Input Power Connection Audio Output Pair 1 Message Play Contact Pair 2 RS485/Security OutputPair 3 -24VDC Output 2A Pair 4
PAGE 5
R e m o te Ainti S g le ti P o le S it h V a lc o m A m p li fie d S u p e r v is e d S p e a k e r s R e m o te M e s s a g e P la y Ie t R S 2 32 P ro g ra m P o rt d n u o rG L a p to p c o m p u te r g a s s e M l e c n a C 8 e g a s s e M 7 e g a s s e M 6 e g a s s e M 5 e g a s s e M 4 e g a s s e M 3 e g a s s e M 2 e g a s s e M 1 e g a s s e M C o n n e c t fie ld w ir in g d ire c tly to s p e a k e r te r m in a ls o r s p e a k e r p ig ta ils .
PAGE 6
Message Panel Connections Audio Interface Message Panel Tip Out Message Panel Ring Out Audio Input Audio Output Message Panel Play Contact Message Panel Play Contact V-2001A Override Input J2 Tip and Ring Override Figure 5: Connections to V-2001A Override Port Message Panel Connections Audio Interface Message Panel Tip Out Audio Input Audio Output Message Panel Ring Out N.C. Message Panel Play Contact N.C.