Operating instructions

ManualsBrandsValor ManualsHome building and Decor534AN

GV60 Remote Electronic Ignition and Control System

OPERATING INSTRUCTIONS

If the information in this manual is not followed

exactly, a fire or explosion may result causing

property damage, personal injury or loss of life.

A. BEFORE OPERATING smell all around the

appliance area for gas. Be sure to smell next to the

floor because some gas is heavier than air and will

settle on the floor.

WHAT TO DO IF YOU SMELL GAS

 Do not try to light any appliance.

 Do not touch any electrical switch; do not use any

phone in your building.

 Immediately call your gas supplier from a neighbor’s

phone. Follow the gas supplier’s instructions.

 If you cannot reach your gas supplier, call the fire

department.

B. Use only your hand to push in or turn the gas control

knobs. Never use tools. If a knob will not push in

or turn by hand, don’t try to repair it, call a qualified

service technician. Force or attempted repair may

result in a fire or explosion.

C. Do not use this control or any gas appliance if any

part has been under water. Immediately call a

qualified service technician to inspect the control or

gas appliance to replace any part of the control

system and any gas control which has been under

water.

D. These instructions are to be referenced as a user

guide, and do not supersede appliance

manufacturer’s lighting instructions.

SPECIFICATIONS

Gas combination control according to CSA or CE approval

(see label).

Fuels: CSA: Suitable for use with natural, manufactured,

mixed and propane (LP) gases and LP gas-air

mixtures.

CE: Suitable for use with gases of EN 437 gas

family 1, 2, 3.

APPLICATION

e-FLAME is a battery-powered electronic remote ignition

and control system for gas appliances with pilot burners

and ODS systems.

OPERATING INSTRUCTIONS

AUTOMATIC IGNITION

When pilot ignition is confirmed, motor turns

automatically to maximum flame height.

Follow appliance manufacturer’s instructions for gaining

accessibility to the gas control and the pilot. When

turning main valve knob, do not force. Knob has a slipping

clutch, allowing for manual main burner(s) flame height

adjustment as well as adjustment to pilot stand by

position (see figure 1).

Figure 1: Combination Control GV60

MAN-Knob (optional) for

Manual Ignition

Main Valve Knob

Connection

Piezo Igniter,

Tab 2.8 x 0.8 mm

Connection Pilot Gas

8 Wire Receiver Jack

ON/OFF Switch

(optional)

Microswitch

Piezo Igniter

(optional)

Summary of content (4 pages)

PAGE 1
GV60 Remote Electronic Ignition and Control System OPERATING INSTRUCTIONS SPECIFICATIONS If the information in this manual is not followed exactly, a fire or explosion may result causing property damage, personal injury or loss of life. Gas combination control according to CSA or CE approval (see label). Fuels: CSA: Suitable for use with natural, manufactured, mixed and propane (LP) gases and LP gas-air mixtures. CE: Suitable for use with gases of EN 437 gas family 1, 2, 3. A.
PAGE 2
Operating Instructions OPERATING INSTRUCTIONS MANUAL IGNITION OPTION 1. STOP! Read the safety information included before proceeding. (If equipped with optional MAN-Knob) 2. Turn main valve knob to the OFF, full clockwise position. Follow appliance manufacturer’s instructions for gaining access to the gas control and the pilot. 3. Place manual ON/OFF switch (if equipped) to the O (OFF position). When turning main valve knob, do not force.
PAGE 3
Operating Instructions 10. Turn main valve knob to the full ON, full counterposition clockwise 4. Turn main valve knob to the OFF full clockwise position. 11. If the appliance will not operate, follow the instructions “TO TURN OFF GAS APPLIANCE” and call your service technician or gas supplier. 5. Replace appliance accessibility cover (if applicable), per appliance manufacturer’s instructions. NORMAL OPERATION A.
PAGE 4
Operating Instructions C. ADJUSTMENT - FLAME HEIGHT INFRARED MODEL GENERAL NOTES A code is preset for all Mertik Maxitrol electronics, but can be changed if required. If you wish to change the code, complete the following: To increase flame height press simultaneously ___ (star, up arrow) and the small lower button. There is a separate button left for switching off (see figure 5). 1. Change DIP switch position (see figure 6).