USER MANUAL MOBILE MULTIMEDIA SYSTEM WITH 7" WIDE TOUCH SCREEN LCD MONITOR Model: SD-906W
Table of Contents DVD Region Management. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. 2 Safety Information 3 Installation 4 Main Unit Display- Monitor Closed . Main Unit Oisplay- Monitor Open . . 10 General Operation . 11 II I...• ~ ~_ 14 16 Radio Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 RBOS Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Safety Information Please read all instructions carefully before installing or operating. Due to its technical nature, it is highly recommended that your unit is installed by a professional installer or an authorized dealer. This product is only for use in vehicles with 12VDC negative ground only. Safety Notes: The DVD video display of the in-dash unit will not operate while the vehicle is moving. This is a safety feature to prevent driver from distracting.
Installation Please read the manual before installation. Before You Start • Disconnect negative battery terminal. Consult a qualified technician for instructions. • Avoid installing the unit where it would be subject to high temperatures, such as from direct sunlight, or where it would be subject to dust, dirt or excessive vibration. Getting Started • Insert the supplied keys into the slots as shown, and slide the unit out of the mounting sleeve .
Installation Wiring Diagram L rj! @ --:B::..::.::....lue_ ® -@ Black ® 11l-_:::.:;Bla:.::;ck::.....--er,VlI ~ Green with White Stri~ ® I L---...:.P~in~k__@ Rear Red @ White/Black ® H Gray/Black @---------, L.
Installation Wiring Diagram - Components 1. Media Device connecting cable 2. Bluetooth Microphone 3. Radio Antenna 4 Car Phone (Brown) 5. Dimmer (Orange) 6. Rear Zone Audio Out LlR & Rear Monitor 1 * Red: Rear Zone Out R * White: Rear Zone Out L * Yellow: Rear Monitor 7. Center RCA Output(Gray) : The center output must be connected to an external amplifier for 3D or 6CH mode. 8. Subwoofer RCA Output(Blue): The subwoofer output is available in all sound/audio modes. 9.
Installation Wiring Diagram - Optional AN Connections DVD Player Game Console Overhead Monitor o 00 •• Rear View Camera Headrest Monitor Front Amplifier Sub Amp lifier Center Channel Amplifier Rear Amplifier The diagram above illustrates the connection capabilities of the unit. Two separate AudioNideo inputs allow the connection of a DVD player or game console.
Main Unit Display Monitor Closed ® @@@@ CD @ @ @) @ @ (f) ® Chapter / Track Up Band AS / PS (Auto Store/Preset Scan) Secondary LCD DISP (Display) Open / Close Monitor Eject Qjl Chapter /Track Down © Stop © Play / Patse t9 Fast Forward @ Fast Reverse ® Mode USB Port ® SO Card ® EO @ @ Power MuteNolume Monitor Notes: This model incorporates a motorized moving monitor. Before final installation, make sure the monitor will not obstruct the dash, shifter or any other controls.
Main Unit Display Monitor Open @ @ @ @---- @ @ TILT DOWN- Press ... to decrease the monitor view angle. @ TILT UP- Press Ato increase the monitor view angle. @ INIOUT - Press to move the monitor forward and backward. DIM - Press to change brightness level of LCD backlight. Safety Notes: The DVD video display of the in-dash unit will not operate while the vehicle is moving. This is a safety feature to prevent driver distraction.
Remote Control ® ® Display @ @ @ @ Next Chapter @ Eject Previous Chapter Enter / Play Fast Forward Fast Reverse @ Mode @ Power @ Mute @ @J @ @ @ @ @ @) ® @ SRC Picture @ Direction Key [Down] @ Zoom / Call Number Key ® Audio Select @ Subtitle Volume Up ® Volume Down Setup Direction Key [Up] @ Angle @ Repeat @ Title Direction Key [Left] Direction Key [Right] @ @ Direct to Folder ® Goto 10 Stop / Band / Hang up Audio Menu
General Operation POWER On/Off Monitor OPEN/CLOSE Press POWER or any other button (except OPEN) to turn the unit on. Press and hold POWER for more than 2 seconds to turn the unit off. Press OPEN to open or close the monitor. The unit will emit 1 confir-mation beeps. Be careful not to touch the monitor during the open/ close sequence.
General Operation Monitor Angle Position (Left/Right) To adjust the monitor positon Left/Right: • Make sure the monitor is in the "OUT" position.Press IN/OUT • Grasp both side of the monitor near the bottom and gently pull on side until the mechanism is fully extended. To return the monitor mechanism to the "closed" position • Grasp both side of the monitor near the bottom and gently push on the side that is extended until the mechanism is closed .
General Operation Clock Set With the monitor closed: 1. Press DISP button(4) to display the clock. 2. Press and hold DISP button(4)until a confirmation beep is heard, then release. 3. Press .. or T to adjust the hours and .... or ~ to adjust the minutes.
Main Setup Menu Enter/Exit Main Setup Menu General System Time OSD Language Beep TFT Auto Open TS Calibrate 1. Press MAIN SETUP in the mode selection display. 2. Press Iii] in left side of screen to exit setup mode and return to the last screen. There is three available sUbjects of setup to select., which are General, ASP, Video. Once enter the MAIN SETUP menu, it will be displayed as General screen. Press the Syetem Time menu bar on screen to open Clock Adjustment display.
Main Setup Menu 3.Press 0 at up-left, dwon-Ieft, down-right and up-right corner on screen as displayed below. Use Default Settings ASP Bass Cent Freq Press Use Default Settings menu bar on screen to choose YES/NO. Press Yes to reset the unit, which will be turned off automatically. At the bottom part of the screen of MAIN SETUP menu, there are three available items: General, ASP, Video. Press ASP item to display audio setup menu. To change the Bass Cent frequency from 60Hz, 80Hz, 100Hz, 200Hz.
VIDEO Operation VIDEO Display Mode Video Input Camera Image At the bottom part of the screen of MAIN SETUP menu, there are three available items: General, ASP, Video. Press Video item to display audio setup menu. Press
Radio Operation Radio When you turn on the unit at first, radio mode will displays on screen automatically. - If the radio mode is wanted when the user in other mode, press MODE button (16) in remote control or press the mode icon at up-left side of screen to go back to the mode selection display to find radio mode icon. Band Automatic Scanning Manual Scanning Press BAND button(1) on the remote control or BAND on screen, the current band will change among AM band and FM3 bands in display.
Radio Operation EQ Press EO button to enter the Audio Adjust screen. EO has 5 basic different audio effects, which are User, Classical, Rock, Jazz and Pops. The user can adjust the FAD(Fade), BAL(Balance) and LOUD(Loudness) by pressing .... , ~. - If you select User, the Bass and Treble bars are activated. The user can select from -7 to 7 levels of Bass and Treble effect. LOC/DX Press LOC/DX to change the sensibility of the unit. When select LaC, the sensibility will decrease to 20dB.
RBDS Operation TA (Traffic Announcement) TA lets you receive traffic announcements automatically, no matter what source you are listening to at the moment. TA can be activated for both a TP station or an enhanced other networks TP station. - To turn TA off/on, touch TA in screen. - When recieving Traffic Announcement, if the volume is low than 16, it will be changed to 16.
RBDS Operation TA Volume Clock Tune You can select volume between 0-39. Select "On", when you drive to different place, clock can adjust automatically. TA Option Seek I Alarm. TA Retune Long I Short.
CD Player Operation CD Mode Press MODE button(16) in remote control or touch the mode icon at up-left corner of screen to go to the mode selection display, and press DVD mode icon.(DVD mode icon is only activated when already inserted a disc.) Disc Insert/Eject Play/Pause Stoping play Moving Track Place CD, label side up, into the disc slot. After inserting the disc, playback starts automatically and the CD mode's playback display shows. To stop the playback and eject the disc, press Eject button.
CD Player Operation Repeat Play Press REPEAT button(39) in remote contral or NEXT, REPEAT on screen to repeat the current track. "Repeat Single" will be displayed shortly on screen. Press again to repeat the full contents of disc. "Repeat All" will displayed. Press third time to go back normal play. "Off' will displayed. Press NEXT, Random Play E:I in display to play all tracks on the disc in random, displaying "Random" on screen.
MP31 WMA Player Operation Mp3/WMA Player You can play MP3IWMA files stored in disc/SO card/USB. Functions as play, pause, stop, track selection, fast forward/reverse, repeat play, intro scan, random play, etc. are the same for MP3IWMA and CD operation. Please see the CD player operation section for the instruction about these functions. After MP3IWMA disc/SO card inserted or USB connected, UMP3" or "WMA"and its information displays on screen and the file in disc will be played automatically.
DVD Player Operation DVD Player When the unit is properly installed, DVD video cannot be displayed on the main TFT screen unless the parking break is applied. If you attempt to playa DVD while the vehicle is moving, the TFT screen displays "WARNING! PITURE OFF FOR YOUR SAFETY" with a blue background. * Rear video(installed for backseat), if applicable, will operate normally. * Functions as switching mode, disc insert/eject, play, pause, stop, selecting track, .fast forward/reverse, etc.
DVD Player Operation Go to Title Menu Press TITLE button(40) in remote control or NEXT, MENU on screen to go to DVD title's starting menu. Selecting Angle Press ANGLE button(38) in remote control or NEXT, ~on screen repeatedly to view multiple picture angles recorded in disc in sequence. Selecting Subtitle Press SUB.T button(36) in remote control or NEXT. SUB-T on screen repeatedly to display subtitles recorded in sequence.
DVD Player Operation DVD SETUP 1. When playing DVD/CD, press SETUP button(29) in remote control or press SETUP in screen to show DVD SETUP display. 2. After set up, to go back to DVD playback, press SETUP button(29) in remote control or ~ at up-right side of screen. If no response for 10 seconds, it will automatically go back to DVD playback. Set Rating PWD The Set Rating PWD and Parental Control is concering with the DISC setup of the DVD. 1. Press Set Rating PWD(Password) bar menu on screen. 2.
DVD Player Operation Parental Control AUDIO ADJUSTMENT You can set parental control to keep children from harmful video. 1. Press Parental Control menu bar in DVD setup display. 2. Number keypad will be displayed for entering password before setting. 3. Press .... , ~ by Parental Control to set one control grade among a.Adult /7.NC-17 / 6.R / 5.PG-R / 4.PG-13 / 3.PG / 2.G / Kid Safe. The following contents are about the AUDIO ADJUSTMENT of DVD Downmix 1.When the disc supports 5.
DVD Player Operation Dolby 5.1CH Some discs support 5.1-channel Dolby Digital surround sound. When this kind of disc is inserted the unit. you can adjust the 5.1-channel audio effect on your preference. 1. It should be selected "Off' of Prologic II and Downmix in DVD setup menu for enjoying 5.1 CH sound effect. 2. Press A.SEL button(26) in remote control or EQ in screen when disc playback. 3.
DVD Player Operation Disc Language Setup Speaker Speaker Volume Setup Test Tones Bass Manage After language setup at DVD setup mode, when playing disc, the selected language will be applied/shown. (if available at the disc) - Subtitle / Audio / DVD Menu: Press <4 , ~ by the menu bar on screen to select a desired language. After entering DVD setup mode. press Speaker display on screen to show speaker setup menu. - Front Speaker: Press
DVD Player Operation Speaker Channel Gain Front Left Channel Gain: Press .... , ~by FL CH Gain menu bar in screen to adjust the front left speaker's volume effect. Front Right Channel Gain / Center Gain / Rear Left Channel Gain / Rear Right Channel Gain / Subwoofer Gain: 1. Press Tat leftside of Speaker setup display to turn to the third page menu. 2. Press .... , ~by FR CH Gain / Center Gain / RL CH Gain / RR CH Gain / Subwoofer Gain menu bar in screen to adjust the speaker's volume effect.
DVD Player Operation • Here are some tips for OSD(On Screen Display). It is convenient for operation.We can divide the screen into several areas as below. A B D E C F Touch A area, launcher MENU will appear. rs!J M~. ~ --..-',-', AUXIN •• K.. .~ ~ ~~ . RLU£TOOIH )#~ ~ ........ eAM~ SD ~ SETUP Tounch B area, SETUP MENU will be showned(26). Touch C area, DVD Menu will be showned(Page24 and 25). Touch D area, you can operate Chapter down function.
JPEG Operation You can see JPEG file stored in disc/SO card/USB. When using a disc, it should be operated in OVO mode. When using SO CARD, select the corresponding mode at mode selection display. . Slide Show Operation 1. When JPEG mode is played, slide show will be operated automatically. A slide stops for 5 seconds and goes to next file in alphabetical/ number order of file name. 2. Press ~II button(13) in remote control or ~II in screen to play! pause. 3.
USB/SO Card Operation Play Each Source Press MODE button(16) or press the current mode icon at up-left of screen to go to mode selection display and press USB / SD card mode icon. According to the source stored in USB or SD card, you can play it. The source types compatible with this unit are in specification on page.
BLUETOOTH Operation Bluetooth Mode This unit supports Bluetooth wireless connection with a bluetooth cell-ular phone. Note: - Before using the bluetooth function in unit, please check that microphone is installed to this unit. - Digital noise & echo suppression system built-in. - Provides the best sound clarity with little or no distortion. (Echo and side-tone might be sensitivity depending upon cellular phone's characteristics or service networks) - Full duplex conversation - Bluetooth version 2.
BLUETOOTH Operation Pairing 1. Click Pair in screen to have the unit prepare starting pairing. It will display "Waiting for Pairing" in screen. 2. Enable your cellular phone's bluetooth pairing. If the cellular phone requires the pin code, enter 1 2 3 4. 3. It will display "Pair OK " on screen when the paring is completed.
Media Device Operation Note: - You should connect your Media Device with this unit first using the cable supplied. - After connecting Media Device the current mode will change to Media mode and the unit will start playing the selected list or play all files registered on the Media Device if no selected list. - The unit will not operate, or may operate improperly with unsupported versions.
Troubleshooting Problem No power to unit No sound can be heard or the volume is low Cause Corrective Action Fuse(s) blown Check/replace fusees) in vehide fuse box Speakers are not wired correctly Connect speaker harness; check speaker wires Speaker wires shorting to chassis ground or to each other Check splices, insulate all bare wires Fader or Balance incorrectly adjusted Check audio settings AV1 or AV2 correctly Check wiring not wired Disc is upside down Insert disc right side up Disc is
Specifications CEA Power Ratings Power Output: 18watts RMS x 4channels into 4-ohms @ < 1% THD+N Signal to Noise Ratio: 90dBA below reference (Reference: 1watt, 40hms) Dynamic Power: 36watts @ 40hms x 4channels Frequency Response: 20Hz - 20kHz (-3dB), AudioNideo input used as source reference Standard Power Supply: 14.
Specifications AM Tuner Monitor General Tuning Range: 530 - 1720kHz Sensitivity (-20dB): 30uV Signal to Noise Ratio @ 1kHz: 50dB Image Rejection: 60dB Frequency Response: 50Hz - 2kHz, -3dB Screen Size: 7" (Measured diagonally), 16:9 Widescreen 7"(145mm)H x 3.
Place Postage Here VilLOR MULTIMEDIA Valor Warranty Validation Dept 18061 ArenthAve City of Industry .
VilLOR MULTIMEDIA ONE YEAR LIMITED WARRANTY Valor Multimedia hereby warrants to the original retail purchaser of this product that should this product or any part thereof, under normal use and conditions,be proven defective in material or workmanship within one year parts and labor from the date of original purchase. Such defect(s) will be repaired or replaced with reconditioned product (at Valor Multimedia's option) for parts and repair labor.
