User's Manual

Computer, TV, Mobile Phone, Speaker, Microphone, etc.
DC 12V IN
Power Adapter (Supply)
Power Cable (Supply)
USB 3.0 Cable
（Supply）
USB 2.0 Cable
（Not Supply）
HDMI Cable
（Not Supply）
9 Remote Control Pairing
Note: The remote control has been paired with the whole machine when
it leaves the factory, and it can be used normally without special
operations. Unless there is an abnormal remote control, the whole remote
control is confused, the remote control is missing, etc., and the remote
control needs to be re-matched, the following steps are used to re-pair.
Step 1 Connect the camera to the power supply and wait for the camera
initialization to complete, and the camera can output pictures normally.
Step 2 Clear t
he paired status of the remote control:
Press and hold the Menu + OK button at the same time until the remote
control indicator light with steady red, release the buttons to clear the
paired status of remote control.
Step 3 Trigger the camera to enter the remote control pairing mode:
Use the card pin to poke the reset button of the camera, the camera's
LED light will switch to a blue marquee effect when it enters the pairing
mode normally. (Note: There is only 15s operation time while entering
the pairing mode. After the timeout, the pairing mode will be automatically
exited and the LED is not a blue marquee effect. Press the reset button
again to reenter the remote control pairing mode.)
Step 4 Start pairing: Press and hold the Menu button unitl the indicator on the
complete. When the normal pairing is successful paired, the camera's
remote control light with red, and then wait for the matching to LED light
is blue with a flashing effect. Now, your camera can be operated through
the remote control normally. If the pairing fails, please repeat steps 2, 3
and 4 until the matching is successful.
10 GUI Settings
10.1
Press【MENU】key under normal image, the screen will display as below:
10.3
Move the cursor to "Information" in the main menu, and press [OK] to enter the
Note: The above information is for reference only, please refer to the real
product for the actual specifiction.
information page as below:
INFORMATION
Version
XXXX
Model M8.V
Date 2021-XX-XX
Return
10.4
Move the cursor to "Restore Default" in the main menu, and press [OK]
to enter the restore default page as below:
RESTORE DEFAULT
Yes
No
Return
Yes / No: Confirm or cancel restore factory settings.
11 Maintenance & Troubleshooting
12 FCC & IC Statement
Camera Maintenance
 If camera is not use in long-term, please disconnect power switch after use.
 Use soft cloth or cotton paper to remove dust from the camera housing.
 When cleaning the camera lens, please use dry soft cloth to wipe, if dirt is
serious, use neutral cleaner gently. Do not use strong or corrosive
detergent, lest the lens scratch, affect the image effect.
Avoid Using
 The camera should avoid shooting particularly bright objects, such as
sunlight, lights, etc.
 The camera should not work under unstable lighting conditions, otherwise
the image will flash.
 Do not use around facilities that can transmit high-power radio waves, such
as television station or radio-transmitting station.
Troubleshooting
The video image displayed by the camera lens has jitter.
1) Check whether the camera installed position be stabled.
2) Check whether have vibrating machinery or object near the camera.
079.79.1101081_V1.0
MENU
Information
Restore Default
MENU
Setting
Information
Restore Default
Exit
10.2 Setting
Move the cursor to "Setting" in the main menu, and press [OK] to enter the
setting page as below:
SETTING
Language English
Video Setting
Audio Setting
EPTZ On
Zoom Limit 3x
HDMI Format 4K@30
Tracking Mode OFF
Return
Language: Optional items: English, Chinese & Francais.
Video Setting: Setting 2D NR, 3D NR, WD R Enable, Flip-H, Osd Mirroring.
Audio Setting: Setting 3A Enable, Mic Equalizer
.
EPTZ: Optional items: On, Off.
Zoom Limit: Optional items: 1.5x, 2x, 3x, 4x, 5x
.
HDMI Format: Optional items: 1080P@60, 1080P@50, 1080P@30, 4K@30.
Tracking Mode: Optional items: Off, Participants, Speaker.
Tracking Effect: Optional items: Smooth, Instaneous (Effective only in
Participants or Speaker of Tracking Mode).
Tracking Speed: Optional
items: Slow, Normal, Fast (Effective only in
Participants or Speaker of Tracking Mode).
GUI menu and parameter information are subject to change without notice.
DC12V
USB HDMI
3.0
USB
2.0
H, Osd Mirroring
NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of
the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help
Changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) this device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause
undesired operation.
This device contains licence-exempt transmitter(s)/receiver(s) that comply with
Innovation, Science and Economic Development Canada’s licence-exempt
RSS(s). Operation is subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may
cause undesired operation of the device.
L’émetteur/récepteur exempt de licence contenu dans le présent appareil est
conforme aux CNR d’Innovation, Sciences et Développement économique
Canada applicables aux appareils radio exempts de licence. L’exploitation est
autorisée aux deux conditions suivantes :
(1) L' appareil ne doit pas produire de brouillage;
(2) L' appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d' en compromettre le fonctionnement.
8 Installation and Connection
1
2
3
4
5
6
Drill on the wall
Install expansion bolts
Fix bracket on the wall
Screw Lock
Fix camera on the bracket
Wall-mounted effect picture