HOME THEATER HDMI® Splitters over 2 UTP Vanco Part Numbers 280718 (1x8) 280714 (1x4) Technical Support www.vanco1.com • info@vanco1.
DEAR CUSTOMER Thank you for purchasing this product. For optimum performance and safety, please read these instructions carefully before connecting, operating or adjusting this product. Please keep this manual for future reference. This product is 100% inspected and tested in the United States to verify HDMI performance parameters. WARNING 1. Do not expose this unit to water, moisture, or excessive humidity. 2.
FEATURES Super IR Control These units have the capability of being controlled via IR signals. The splitter can be controlled from the display. This is accomplished by using an optional IR Receiver pigtail (Part # 280721) pointing away from the display(s), which can be connected to the receiver boxes at each display. The IR Transmitter pigtail (Part # 280720) is then connected to the splitter and pointed at the source(s). A remote control is used at the display to select the splitter inputs and outputs.
HDMI® 1 x 4 Splitter over 2 UTP with IR Part # 280714 • Allows 1 HDMI Source to be Connected to 4 HDMI Displays Devices over Dual Cat5e/Cat6 Cables • Transmission Range: Extends 1080p resolutions up to 100 ft over Cat5e Cables; Extends 1080p resolutions up to 110 ft over Cat6 Cables • High Speed Chip Set that Supports 3D and 4K x 2K • Full HD1080P/60HZ • HDCP Compliant • Super IR, IR transport channel can be forward or backward, an IR adapter and transmit and receive pigtails are needed • Unique Circuit D
PACKAGE CONTENTS Before attempting to use this unit, please check the packaging and make sure the following items are contained in the shipping carton: • One HDMI Splitter • Power Supply • 4 Receivers included with 1x4 and 8 Receivers included with 1x8 • Product Manual • Two Mounting Ears for Part #280718 CONNECT AND OPERATE Connect the signal source such as Blu-Ray Player, Play Station 3, audio/video receiver, cable or satellite receivers and computers equipped with HDMI output interfaces with a
CONNECTION DIAGRAM Super IR Control System Over UTP Cable Blu-Ray Player HDTV Sender Receiver HDMI IR IR TX Pigtail IR Remote (1 per display for Matrix, Switches, Extenders 1 per source for Splitters) 6 HDMI 2 UTP Cables IR RX Pigtail www.vanco1.
280718 PRODUCT IMAGES 800-626-6445 7
280714 PRODUCT IMAGES 8 www.vanco1.
TROUBLE-SHOOTING 1. Best results are usually achieved when the source and display resolutions are the same. If resolutions differ, the splitters will try to adjust the signal to match the resolution of the HD TV with the lowest resolution. This will result in a picture with a lower resolution on the other HD TV sets. 2. If you do not get audio and video see if you can use the “set-up” menu on the TV to adjust the audio settings and the video settings.
LIABILITY STATEMENT Every effort has been made to ensure that this product is free of defects. The manufacturer of this product cannot be held liable for the use of this hardware or any direct or indirect consequential damages arising from its use. It is the responsibility of the user and installer of the hardware to check that it is suitable for their requirements and that it is installed correctly. All rights are reserved.
TECHNICAL SUPPORT In case of problems, please contact Vanco Technical Support by e-mail at support@Vanco1.com or call 1-800626-6445 between the hours of 8am and 5pm central US time zone on Monday through Friday. When calling, please have the Model Number, Serial Number (affixed to the bottom of the unit) and Invoice available for reference during the call.
Vanco® International 506 Kingsland Drive Batavia, Illinois 60510 call: 800.626.6445 fax: 630.879.9189 visit: www.vanco1.