4K HDMI® EXTENDER over single Cat5e/Cat6 Cable Vanco Part Number EV4K2006 4K HDMI® Extender over Single Category 5e/6 Cable with POE www.vanco1.com • 800.626.
DEAR CUSTOMER Thank you for purchasing this product. For optimum performance and safety, please read these instructions carefully before connecting, operating or adjusting this product. Please keep this manual for future reference. This product is 100% inspected and tested in the United States to verify HDMI performance parameters. WARNING 1. Do not expose this unit to water, moisture, or excessive humidity. 2.
FEATURES INTRODUCTION The Evolution by Vanco EV4K2006 HDMI Extender over Single Cat5e/6 with Bi-directional IR, auto EDID/EQ, and Bi-directional PoE extends 4K ultra high definition video with HDR and audio signals, IR, and power. Extends 4K@60Hz, 4:4:4 Chroma Subsampling and HDR up to 164ft/50m, and 4K@30Hz, 4:4:4 Chroma Subsampling, and HDR up to 130ft/40m.
SPECIFICATIONS TECHNICAL SPECS HDMI Compliance....................................................... HDMI Deep Color 30/36/48 bit color depth, Full 3D HDCP Compliance....................................................... Yes Video Bandwidth......................................................... 594 MHz Video Support............................................................ 480i/480p/720p/1080i/1080p/4Kx2K @60 Audio Support............................................................
PANEL DESCRIPTIONS Transmitting Unit 1 Receiving Unit 2 3 8 5 6 4 9 10 12 13 7 11 14 1. HDMI INPUT: Connect a source such as a Blu-ray player, cable box, computer, NVR/DVR, etc. 2. IR TX – Plug in included IR Blaster to control the source (see IR section for setup and installation) 3. IR RX – Plug in included IR Receiver to receive remote signals (see IR section for setup and installation) 4.
CONNECTION DIAGRAM CONNECT AND OPERATE 1. Connect a source such as a Blu-Ray Player, game console, A/V Receiver, Cable or Satellite Receiver, etc. to the HDMI input on the Transmitting unit. 2. Connect a display such as an HDTV or HD Projector to the HDMI output on the Receiving unit. 3. Connect a single Category 5e/6/7 up to 164ft/50m to the UTP output of the Transmitting unit, and the other end to the UTP input of the Receiving unit. 4.
IR IR PASS-THROUGH The bi-directional IR system allows you to control the source that is connected to the extender unit, from the display; or the display from the source. There are two important things to note when setting up the IR system: 1. The IR Receiver (IR RX) is always what you point your remote at to send an IR signal. This pigtail is placed at the display for controlling the source; or at the source for controlling the display. 2.
IR RECEIVER (RX) • To control the source: Plug IR Receiver into IR RX port of receiver unit (EV4K2006-RX); place receiver at or near display. • To control the display: Plug IR Receiver into IR RX port of transmitter unit (EV4K2006-TX); place receiver in position where it is able to receive remote signals. To Control the Source: To Control the Display: 1. Plug the IR Blaster into the IR TX Port on the Transmitter 1. Plug the IR Receiver into the IR RX Port on the Transmitter 2.
NOTICE 1. Vanco HDMI and Cat5e/6 cables are strongly recommended for use with this product to ensure best results. 2. Incorrect placement of IR Blaster and Receiver may result in the failure of the IR extenders. Please check carefully before plugging in the IR extender to the respective IR sockets. 3. The transmission length is largely affected by the type of Cat5e/6 cables utilized, the type of HDMI sources, and the type of HDMI display.
TROUBLE-SHOOTING 1. Best results are usually achieved when the source and display resolutions are the same. If resolutions differ, the extenders will try to adjust the signal to match the resolution of the HDTV with the lowest resolution. This will result in a picture with a lower resolution on the other HDTV sets. 2. If you do not get audio and video, access the “setup” menu on the TV to adjust the audio and video settings.
LIMITED WARRANTY With the exceptions noted in the next paragraph, Vanco warrants to the original purchaser that the equipment it manufactures or sells will be free from defects in materials and workmanship for a period of two years from the date of purchase. Should this product, in Vanco’s opinion, prove defective within this warranty period, Vanco, at its option, will repair or replace this product without charge. Any defective parts replaced become the property of Vanco.
® Vanco International 506 Kingsland Drive Batavia, Illinois 60510 call: 800.626.6445 fax: 630.879.9189 visit: www.vanco1.
