HDMI® EXTENDER over single Cat5e/Cat6 Cable Vanco Part Number EVEX2006 HDMI® Extender over Single Category 5e/6 Cable with POE www.vanco1.com • 800.626.
DEAR CUSTOMER Thank you for purchasing this product. For optimum performance and safety, please read these instructions carefully before connecting, operating or adjusting this product. Please keep this manual for future reference. This product is 100% inspected and tested in the United States to verify HDMI performance parameters. WARNING 1. Do not expose this unit to water, moisture, or excessive humidity. 2.
FEATURES INTRODUCTION The Evolution by Vanco EVEX2006 HDMI Extender over Single Cat5e/6 with Bi-directional IR, auto EDID/EQ, and PoE extends high definition video and audio signals, IR, and power at a distance of up to 164ft/50m over a single Cat5e/6 cable. Power over Ethernet (PoE) Technology transmits power over Cat5e/6, allowing either the Transmitter or Receiver to be powered without the use of a power supply.
SPECIFICATIONS TECHNICAL SPECS HDMI Compliance....................................................... HDMI Deep Color 30/36/48 bit color depth, Full 3D HDCP Compliance....................................................... Yes Video Bandwidth......................................................... Single-link 165MHz [4.95Gbps] Video Support............................................................ 480i/480p/720p/1080i/1080p @60 HDMI over UTP...........................................................
PANEL DESCRIPTIONS Transmitting Unit 1 4 Receiving Unit 2 5 6 3 8 7 11 9 10 12 13 14 1. HDMI IN - Connects to a HDMI source with a HDMI male-male cable 2. IR Blaster - Infrared 3.5mm socket for plugging in the extension cable of IR blaster 3. IR Receiver - Infrared 3.5mm socket for plugging in the extension cable of IR receiver 4. 12 V DC - Connect to 12 V DC power supply 5. Power Indicator Light 6. Status Indicator Light 7.
CONNECTION DIAGRAM CONNECT AND OPERATE 1. Connect a source such as a Blu-Ray Player, game console, A/V Receiver, Cable or Satellite Receiver, etc. to the HDMI input on the Transmitting unit. 2. Connect a display such as an HDTV or HD Projector to the HDMI output on the Receiving unit. 3. Connect a single Category 5e/6/7 up to 164ft/50m to the UTP output of the Transmitting unit, and the other end to the UTP input of the Receiving unit. 4.
IR IR PASS-THROUGH The bi-directional IR system allows you to control the source that is connected to the extender unit, from the display; or the display from the source, not simultaneously. There are two important things to note when setting up the IR system: 1. The IR Receiver (IR RX) is always what you point your remote at to send an IR signal. This pigtail is placed at the display for controlling the source; or at the source for controlling the display. 2.
IR RECEIVER (RX) • To control the source: Plug IR Receiver into IR RX port of receiver unit (EVEX2006-RX); place receiver at or near display. • To control the display: Plug IR Receiver into IR RX port of transmitter unit (EVEX2006-TX); place receiver in position where it is able to receive remote signals. To Control the Source: To Control the Display: 1. Plug the IR TX/Blaster into the IR TX Port on the Transmitter 1. Plug the IR Receiver into the IR RX Port on the Transmitter IR TX 2.
NOTICE 1. Vanco HDMI and Cat5e/6 cables are strongly recommended for use with this product to ensure best results. 2. Incorrect placement of IR Blaster and Receiver may result in the failure of the IR extenders. Please check carefully before plugging in the IR extender to the respective IR sockets. 3. The transmission length is largely affected by the type of Cat5e/6 cables utilized, the type of HDMI sources, and the type of HDMI display.
TROUBLE-SHOOTING 1. Best results are usually achieved when the source and display resolutions are the same. If resolutions differ, the extenders will try to adjust the signal to match the resolution of the HDTV with the lowest resolution. This will result in a picture with a lower resolution on the other HDTV sets. 2. If you do not get audio and video, access the “setup” menu on the TV to adjust the audio and video settings.
LIMITED WARRANTY With the exceptions noted in the next paragraph, Vanco warrants to the original purchaser that the equipment it manufactures or sells will be free from defects in materials and workmanship for a period of two years from the date of purchase. Should this product, in Vanco’s opinion, prove defective within this warranty period, Vanco, at its option, will repair or replace this product without charge. Any defective parts replaced become the property of Vanco.
® Vanco International 506 Kingsland Drive Batavia, Illinois 60510 call: 800.626.6445 fax: 630.879.9189 visit: www.vanco1.
