x7 HDMI® Splitter over Single Cat5e/6 Cable Vanco Part Number: EVSP1017 1X7 HDMI® Splitter over Single Cat5e/6 Cable www.vanco1.com • 800.626.
DEAR CUSTOMER Thank you for purchasing this product. For optimum performance and safety, please read these instructions carefully before connecting, operating or adjusting this product. Please keep this manual for future reference. This product is 100% inspected and tested in the United States to verify HDMI performance parameters. WARNING 1. Do not expose this unit to water, moisture, or excessive humidity. 2.
FEATURES INTRODUCTION The Evolution by Vanco EVSP1017 1x7 HDMI Splitter over Cat5e/6 with IR and PoE capability, splits a single HDMI signal to seven outputs over Cat5e/6, with a loop-out HDMI port, which can be used for a local display, or to cascade to create additional outputs. Compatible with the EVRX2006 receiver (sold separately), which requires no power supply as the EVSP1017 provides PoE (Power over Ethernet).
SPECIFICATIONS Power ....................................................................... Maximum 18W (includes PoE) Net Weight ............................................................... 1.675 lb. Video Bandwidth ........................................................ Maximum TMDS clock frequency 148.5MHZ, 4.95Gbps Resolution and distance............................................... 164ft/50m Cat5e/6 @ 1080p 60 24bits Audio formats............................................................
PANEL DESCRIPTIONS 1 7 3 2 8 9 10 4 5 11 6 12 1. POWER SWITCH: Toggle switch that turns the splitter unit ON or OFF 2. POWER LED: Illuminates when the splitter is connected to power 3. UTP LINK STATUS: Illuminates when the UTP outputs are connected to the EVRX2006 or EVWP2006RX receiver units (sold separately) 4. HDMI OUT STATUS: Illuminates when a display is connected to “HDMI OUT” port and is powered on 5. HDMI IN STATUS: Illuminates when the source is connected and is powered on 6.
EDID MANAGEMENT Extended Display Identification Data (EDID) is a data structure provided by a digital display to describe its capabilities to a video source (e.g. graphics card or set-top box). In a nutshell, the display provides its EDID info to the source to send the proper signal format; this is essential for a proper handshake to occur.
CONNECTION DIAGRAM HDTV HDTV HDMI HDTV HDMI Cat5e/6 HDMI Cat5e/6 Use with EVWP2006RX or EVRX2006 (Sold Separately) IR TX Cat5e/6 IR RX Single HDMI Source CONNECT AND OPERATE 1. Connect a source such as a Blu-Ray Player, game console, A/V Receiver, Cable or Satellite Receiver, etc. to the HDMI input 2. Connect the Cat5e/6 runs (home run cabling recommended) to the UTP output(s); connect to the EVRX2006 or EVWP2006RX receiver (sold separately) 3.
IR IR PASS-THROUGH The bi-directional IR system allows you to control the source that is connected to the extender unit, from the display; or the display from the source, not simultaneously. There are two important things to note when setting up the IR system: 1. The IR Receiver (IR RX) is always what you point your remote at to send an IR signal. This pigtail is placed at the display for controlling the source; or at the source for controlling the display. 2.
IR RECEIVER (RX) • To control the source: Plug IR Receiver into IR RX port of receiver unit; place receiver at or near display. • To control the display: Plug IR Receiver into IR RX port of transmitter unit; place receiver in position where it is able to receive remote signals. To Control the Source: 1.
TROUBLE-SHOOTING 1. Best results are usually achieved when the source and display resolutions are the same. If resolutions differ, the extenders will try to adjust the signal to match the resolution of the HDTV with the lowest resolution. This will result in a picture with a lower resolution on the other HDTV sets. 2. If you do not get audio and video, access the “setup” menu on the TV to adjust the audio and video settings.
LIMITED WARRANTY With the exceptions noted in the next paragraph, Vanco warrants to the original purchaser that the equipment it manufactures or sells will be free from defects in materials and workmanship for a period of two years from the date of purchase. Should this product, in Vanco’s opinion, prove defective within this warranty period, Vanco, at its option, will repair or replace this product without charge. Any defective parts replaced become the property of Vanco.
® Vanco International 506 Kingsland Drive Batavia, Illinois 60510 call: 800.626.6445 fax: 630.879.9189 visit: www.vanco1.
