LITHIUM POLYMER BALANCE CHARGE PROGRAM CONNECTION DIAGRAM Lithium polymer balance charge program connection diagram This diagram shows the correct way to connect your battery to the I MAX-B6 while charging In the balance charge program mods only. A WARNING: Allure to connects shown In this diagram will damage this charger. Tha main battery lads must be connected along with the balance lead connector as Shawn bat are charging your battery ..
WARNING AND SAFETY NOTES & Pleads barring mind the following points bafflers commencing charging: Did you select the appropriate program suitable for the type of battery you are charging? Did you set up adequate current for charging or discharging? Have you checked the battery voltage? Lithium battery packs can be wired in parallel and In series, |.6. a 2 call pack can be 3.7V (In parallel) or 7.4V (In peerless.
INITIAL PARAMETER SETUP (USERS SETUP) The battery becomes warm after cycles of charge/discharge process. The program will Insert a time delay after each charge/discharge process to allow the battery sough time to coal down before beginning next cycles of supercharger process. The valid value ranges from 0 to 60 minutes. When the charge process starts, the Integrated safety timer starts to run simultaneously.
INITIAL PARAMETER SETUP (USERS SET UP) The program provides maximum capacity protectorate function. If the Del peak voltage can not be detected or the safety timer times out, o process will stop automatically, wham the battery reaches the user-set s Maximum charge capacity, The beep to confirm users' operation sounds every time & button is pressed. The beep or melody sounds at various times during operation to confirm Char different mode change. These functions can be switched on or off.
Charging of Lithium battery Charging of lithium battery toucan acne noh # «oec ner Bat g deacon’ Ro Mice 2880 The left side of the first line shows the type of battery you choose. The value on the left of the second line of the charger is current user set, After chatting the currant and voltage, press START/ENTER key for more than 3 seconds to start the current: voltage: This displays the number of calls you set up and the processor detects.
Fast charging of lithium battery The value on the left tilde of the second lines sets the charge current. The value on the right side of the second lines sets the battery pack's voltage. After setting current and voltage, press STAR/ENTER for more than 3 seconds to start the process. B gl e EERIE. DEC Nch | DEC INC This displays the number of cells you set up and the processor Sty gy doctors.
STORAGE CONTROL OF LITHIUM BATTERY Storage control of Lithium battery At this screen, you can set up the current and voltage of the battery pack. Charging and discharging will make the batteries cams ta the voltage level of *storage” state. s, . [ This screen shows the real-time status charging. Press BAT TYPE/STOP key once to spat the chars prices Charging lithium battery In the storage mode This function Is for charging/discharging batters which are not used at acne.
Discharging of lithium battery The values of discharge current on tha left can not exceed 1C, and the ‘ value on the right can not be under the voltage recommended by the manufacturer to avoid deep discharging. Press START/ENTER for more than 3 seconds to start discharging. This hows the real-time status of discharging, you can press BAT TYPE/STOP key ta stop discharging. The 4th call was damaged. The value of voltage may be zero If disconnection accursed.
CHARGING OF NICODEMUS BATTERY Charging of NICHIREN battery P This program s for charging of HARMONICA batteries associated with RIG lifts it models applications. You can press START/ENTER key to mask It boink and then INC or DEC to change the parameter values. Crass START/ENTER key lo tore the value. 40EC WCH | spec WCh The screen shows the real-time status. Press BAT TYPE/STOP key to end the program. The sound will emitted to Indicates the end of program.
DISCHARGE OF NICODEMUS BATTERY Discharge of NICJ/NIMH battery Set charge current on the left and the final voltage on the right. Range of the charge current ia range of final voltage is Press START/ENTER key for more than 3 seconds to start the program. TIDES inch Batting Bi op levee mop stands The screen Indicates the discharging state. You can press ‘START/ENTER key to altar discharge currant. Crass START/ENTER again to store the value. Press BAT TYPE/STOP key to stop discharging.
CHARGING OF THEBES BATTERY. Charging of the Pb battery Sst up the charge current on the left and nominal voltage on the right. Range of current is the voltage should match the battery being charged. Press START/ENTER key for more than 3 seconds to start charging. 3 DEC WGP | IDES INCH pond The screen displays the real-time discharging status. Crass START/ENTER key to alter discharge currant. Press START/ENTER key again to stirs the parameter value you set. Press BAT TYPE/STOP key 2o the program.
Discharging of the Pb battery Set up the share currant on the left and nominal voltage on the right. Rang of discharge currant is the voltage should match the battery being charged. Press START/ENTER key for more than 3 seconds o start charging. The screen displays the real-teems discharging status. Press START/ENTER key to alter discharge current. Press START/ENTER in to store the parameter values you set. Press BAT TYPE/STOP . key to ond the program.
Storage data program For your convenience, I MAX-B6 has a data storage and oad program. It can stirs five battery data representing the respective specifications of batteries. You can call back the data when h charging or discharging without setting up the program again. Press START/ENTER key to make it blink, and usa INC or DEC to sst up the parameter. Setting of tha parameter in the screen will not affect the charge and discharge process. They Just present the specification of the battery.
LOAD DATA PROGRAM Load data program This program Is to load the data stored at the *save data® program. Press START/ENTER key to make the data field blink and press INC or DEC for mots than 3 seconds to load the data. Choose the data number you want to call back. The data you want to call back will ba displayed.
VARIOUS INFORMATIONAL_ THE PROGRAM. Parlous Information In the program You can Inquire various Information on the LCD screen during the charging and discharging process. Press DEC key, the charger will display users' setting. You can press INC key to monitor voltage of sate cell wheels the battery is connected with each port of the charger. It comes to the final voltages when the program ended. Displayed capacity cut-off function Is turn on and the setting value of capacity.
WARNING_AND_ERROR MESSAGE Warning and error message I MAX-B8 incorporates varsity of functions for the systems to verify processes and the stats of the electronics. In case of an error the screen will display the cause of error and emit an audible sound. compaction popularly connected. Battery connection is interrupted. Short-cultural of the output termination. Input allow voltage protection. The voltage of the battery pack has been selected Incorrectly The charger has malfunctioned for some reason.
WARNING_ _ANDORRAN MESSAGE Warning and error message ehE T The voltage Is higher than which Is set. Please check the number of cells in the battery pack. naiad Volta's of one cell In the battery pack Is too low, please check the voltage of sate cell. R Voltage of ane call in the battery pack is too high; pleads check the voltage of each call. Wrong connection of the connector detectable. connector and cable.
MAXIMUM CIRCUIT POWER CHART The total cultural power of this charger; (1) Charge : 50 WATS, (discharged: 5 Watts Forth voltage of battery more than 10V, the actual amount of charge current delivered to the battery will automatically will be a3 follows; be limited.
