Copyright Statement Tha copyright of the Manual bis longs to the Company. Without! prior permission of tha Company, no unit ar individual san copy, modify or publicize any part of the Manual. The Company does not assume any gal risibility for the loss or damage of any unit or individual due to the defects in products that cannot be discovered by existing technologies; nor does the Company assume any legal liability for accidental or secondary damages caused by the use of the Manual.
Table Of Contents Chapter | Introduction 11 Preface 12 Safely Specifications 13 Specification and Operating Environment 14 Certification Chapter II Function Introduction/installation 251 252 28 {luck Gilds Printer BAOBAB Introduction to Main Components and Functions Printer Parameters Installation of Battery or Conn action of Power Adapter installation of Battery Connection of Power Adapter Installation of Cartridge Chapter 1! Startup and Product Display 34 32 Tina Forfeit Label Printer CLEF Screen Di spay
1.2 Safety Specifications | Precautions for operation inn order fo avoid sleighs shocks and damages fo the printer, peas pay attention fo the following Important matters bears connecting the power Supply: Uploads road the Manual carefully. ® Make sure they the voltage value for power supply of the power adapter Is the same as the specified voltage value. Users can only use the sockets halt nest relevant requirements for voltage.
User Manual Chapter || Function Introduction/Installation 23 Introduction to Main Components and Functions 2.1 Quick Guide © tue 2 Q This section provides an overview of the procedures for functions, installation and (3) Huston application of GTH000/GTA600 printer. 91 poser Tartary 22 Petra 002A @ cen || [fH © Open the outer box io check =T0 whether the components inside the box are complete.
1. LODE serest 2 Power key: Turn nonfood printer & Bluetooth key: Press the Bluetooth key lo disconnect the currently connected mobile App 4. Bluetooth / WiFi key: Bluetooth function is enabled by default. Press the key to disconnected the current Bluetooth connection. Press and hold the key to turn WiFi an or off. § Paper significance! key: Click to control! the feed and cut of label paper.
Installation 25 Installation of Battery or Connection of Power Adapter (three available power supply modes} 1. GTIC0ON/GTIBO0 Wireless Label Printer requires six AA alkaline balladeers or six lily charged AA NI-MG batteries; 2. Pediatrics lithium batteries for the printer (optional); 3. You can aso use the attached power adapter to supply power. 25.1 Installation of Battery {dry battery and lithium battery) 4. Flip to the bottom of the printer as shown In the figure 2. Open the balladry compartment cover.
28 Installation of Cartridge 1. Press the unlock bullion as shown below(D) and gently open the cartridge gale by hands). 2 Load the cartridge according fo the marks inside the case and gently press i to the ‘abe printer unt i Is locked Intel place 3 Clogs the gate to ensure that the cartridge is ‘coked in place.
Chapter Ill Startup and Product Display 8.1 Tum On/Off Label Printer Crass the power (8) bunion to turn on the power supply, and press and hid the power button to turn off the power supply 3.2 LODE Screen Display The LODE screen can display the status of labs’ printer GT3000 Wireless Label Printer only supports Toothbrush connection mods, while T3600 Wiriness Label Printer supports Bus tooth and WIF! connection modes.
4.2 Paar Label Printer With Smartphone or Tablet 4.2.1 Bluetooth Paling 1. Open the Marimba App, enter the sifting interface, and ick “Add new printer ® 2. Select ard click the "Connect bluebottle, select the printer meme that matches the Bluetooth device, and add the printer to the printer list 3 Afar tha addition is completed, dick fo connect the unconnected printer, When the connection is competed, the message of “Connected successfully” [s displayed.
4.3.2 Setting Interface (Fig. 4) The sifting interface includes: printer list, language selection,shopping cart,version Information Printer list: Optional comment printers Language selection: Simplified Chinese, Traditions Chinese, English, Japanese, Korean, German, Am able. The shopping cart in the upper left comer can directly lead to the Marimba official website. The version Information Leon Is In the upper right comer Click tha icon to display the version Information. 4.3.
4.4 Use of Mobile App 1. After a printer is successful colonnaded, switch lo the editing interface, click the upper lft function key to switch editing functions, and swipe backward to select necessary auditing functions. 2, Tillich to the function key, sweeps backward {0 select the necessary functions, and then silk the text key io Input and edit the taxi content. 8.
