Solutions for Demanding Applications VARTECH S Y S T E M S I N C. 10.
Revision History Date 10/12/09 Rev No 00 Summary Page First Issue 10.
Safety Instructions PLEASE NOTE - This equipment is suitable for use in Class I, Division 2 or non-hazardous locations only. WARNING - EXPLOSION HAZARD - DO NOT DISCONNECT EQUIPMENT UNLESS POWER HAS BEEN SWITCHED OFF OR THE AREA IS KNOWN TO BE NON-HAZARDOUS. AVERTISSEMENT - RISQE D'EXPLOSION - AVANT DE DECONNECTER L'EQUIPMENT, COUPER LE COURANT OU S'ASSURER QUE L'EMPLACEMENT EST DESIGNE NON DANGEREUX. Read the Safety Instructions carefully and keep it for use later.
Explosion Hazard - Substitution of components may impair suitability for hazardous locations. Any Equipment or associated cabling connected to this device must be non-incendive and/or suitable for the Class 1, Division 2 area in which it is to be installed.
Environment and Enclosure Information: Review this information on enclosures before installing the product: ATTENTION: Environment and Enclosure This equipment is intended for use in a Pollution Class 2 industrial environment, in overvoltage Category II applications (as defined in IEC publication 60664-1), at altitudes up to 2000 meters (6561 feet). This equipment is supplied as open-type equipment.
Cleaning the LCD monitor To clean the LCD panel: Wipe the screen gently with a clean lens brush made of camel hair, or a soft, clean, lint free cloth. This is to remove dust and other particles without scratching the LCD panel. If it is still not clean, then wipe with a damp lint free cloth and blow on it to dry. Do not clean the panel with a keton-type material (e.g. acetone), or ethyl toluene, ethyl acid, methyl or chloride. These may damage the LCD panel. Do not apply pressure to the LCD panel.
Computer System: Processor Intel® Atom™ N270, 1.6 GHz processor System Memory 200 pin DDR PC-3200 SO-DIMM 2 GB x 1 BIOS AMI BIOS Hard Drive 320 GB SATA Operating System Microsoft XP Professional (SP3) for Embedded Systems Expansion Slots None Back Panel I/O Ports PS/2 Keyboard Connector x 1 PS/2 Mouse Connector x 1 Power Inlet x 1 RS-232 Port x 3 (x1 422/485 Optional) USB 2.
Power & Operational Specifications: Power Input 100 - 240 VAC 1.5A 50/60 Hz 12 - 24 VDC 6.0A max (optional); SELV source required if used Power Consumption 37W Temperature Operational: -32°F to 140°F Humidity Storage: -4°F to 149°F Operational: 20 to 40°C, 90% RH NC Storage: 0°C to 60°C -20°C to 65°C 5 to 65°C, 28% RH NC Installation of Your Panel PC Packaged with each carton will be: 1 - VTPC100PSS 1 - #10-32 Mounting Hardware 1 - Users Guide (Printed or on CD) 10.
BEFORE MAKING ANY CONNECTIONS OR APPLYING POWER, FIRST READ THROUGH THE ENTIRE MANUAL Panel Mount Procedure Panel Mounting Procedure: 1- Cut and drill the panel (refer to the panel mount drawing, Figure A). Measurements are provided in inches and millimeters. Panel Mounting Cutout: 1- If access to the bottom of the enclosure is not available following installation, attach the power and all necessary cables to the bottom side of the enclosure at this time. 2- Install the enclosure in the prepared cutout.
Panel Mount Drawing: Detail –A– Connections to the Panel Mount PC Bottom Rear View (AC Unit shown) - Connector Panel - 10.
PLEASE NOTE – ANY EQUIPMENT OR ASSOCIATED CABLING CONNECTED TO THIS DEVICE MUST BE NON-INCENDIVE AND/OR SUITABLE FOR THE CLASS I DIVISION 2 AREA IN WHICH IT IS TO BE INSTALLED. Power Connection (Power In) AC models - The AC model of the Panel Mount PC includes an AC line cord which is 3ft long with stripped wires at the connection end. The user must supply a lockable industrial-type power supply plug to mate with their power outlet.
Turning the system On and Off Before connecting the Panel Mount PC to power, connect any peripheral devices. As a general rule, any peripheral device should only be connected or disconnected when the Panel Mount PC is off with the exception of any USB or 1394 peripheral. The Panel Mount PC may be turned on using the main On-Off switch which controls the power outlet to which the unit is plugged in. Once the Panel Mount PC is turned on, the computer power reset switch must be depressed for Windows to start.
