Owner’s Manual Model Year 2013 Edition: June 2012 TS 1651-A-13 KTA-2656/11-VX- 0-1 VAUXHALL Corsa Owner’s Manual Model Year 2013 Edition: June 2012 TS 1651-A-13 KTA-2656/11-VX-en
Contents Introduction .................................... 2 In brief ............................................ 6 Keys, doors and windows ............ 19 Seats, restraints ........................... 34 Storage ........................................ 51 Instruments and controls ............. 68 Lighting ........................................ 95 Climate control ........................... 103 Driving and operating ................. 111 Vehicle care ...............................
2 Introduction Introduction
Introduction Vehicle specific data Please enter your vehicle's data on the previous page to keep it easily accessible. This information is available in the sections "Service and maintenance" and "Technical data" as well as on the identification plate. Introduction Your vehicle is a designed combination of advanced technology, safety, environmental friendliness and economy. This Owner's Manual provides you with all the necessary information to enable you to drive your vehicle safely and efficiently.
4 Introduction Danger, Warnings and Cautions 9 Danger Text marked 9 Danger provides information on risk of fatal injury. Disregarding this information may endanger life. 9 Warning Text marked 9 Warning provides information on risk of accident or injury. Disregarding this information may lead to injury. Caution Text marked Caution provides information on possible damage to the vehicle. Disregarding this information may lead to vehicle damage. Symbols Page references are indicated with 3.
Introduction 5
6 In brief In brief Vehicle unlocking Seat adjustment Seat positioning Initial drive information Turn the key in the driver's door lock to the front or press button q to unlock the doors and load compartment. Open the doors by pulling the handles. To open the tailgate, pull the button underneath the tailgate moulding. Radio remote control 3 20, Central locking system 3 21, Load compartment 3 24. Pull handle, slide seat, release handle. Seat adjustment 3 36, Seat position 3 35.
In brief 7 Seat backrests Seat height Head restraint adjustment Turn handwheel. Do not lean on seat when adjusting. Seat adjustment 3 36, Seat position 3 35, Folding front passenger seat backrest 3 37. Lever pumping motion up = higher down = lower Press release button, adjust height, engage. Head restraints 3 34. Seats 3 36, Seat position 3 35.
8 In brief Seat belt Pull out the seat belt and engage in belt buckle. The seat belt must not be twisted and must fit close against the body. The backrest must not be tilted back too far (maximum approx. 25 °). To release belt, press red button on belt buckle. Seat belts 3 38, Airbag system 3 41, Seat position 3 35. Mirror adjustment Exterior mirrors Interior mirror Setting with four-way switch in version with manual window operation Swivel the lever on the underside to reduce dazzle.
In brief Setting with four-way switch in version with electronic window operation First select the relevant exterior mirror then use the control to adjust. Electric adjustment 3 27, Convex exterior mirrors 3 27, Folding exterior mirrors 3 27, Heated exterior mirrors 3 28. Steering wheel adjustment Unlock lever, adjust steering wheel, then engage lever and ensure it is fully locked. Do not adjust steering wheel unless vehicle is stationary and steering wheel lock has been released.
10 In brief Instrument panel overview
In brief 1 2 Side air vents ...................... 109 Light switch .......................... 95 9 Instrument illumination ....... 100 Electronic climate control system ................................. 105 10 Left heated seat .................... 38 Rear fog light ......................... 99 Front fog lights ..................... 99 3 Headlight range adjustment ........................... 96 Turn and lane-change signals, headlight flash, low beam and high beam ..... 98 Exit lighting ..............
12 In brief Exterior lighting Turn light switch AUTO = Automatic light control: Exterior lighting is switched on and off automatically m = Activation or deactivation of the automatic light control = sidelights 8 = low beam 9 Press light switch > = Front fog lights r = Rear fog lights Lighting 3 95. Headlight flash, high beam and low beam headlight flash = pull lever high beam = push lever low beam = push or pull lever High beam 3 96, Headlight flash 3 96, Automatic light control 3 95.
In brief Turn and lane-change signals Hazard warning flashers Horn right = lever up left = lever down Operated with the ¨ button. Hazard warning flashers 3 98. Press j. Turn and lane-change signals 3 98, Parking lights 3 99.
14 In brief Washer and wiper systems Windscreen wiper & = fast % = slow $ = timed interval wipe or automatic wiping with rain sensor § = off For a single wipe when the windscreen wiper is off, press the lever down. Windscreen wiper 3 70, Wiper blade replacement 3 148. Windscreen and headlight washer systems Rear window wiper and washer system Pull lever. Windscreen and headlight washer system 3 70, Washer fluid 3 145.
In brief Climate control Heated rear window, heated exterior mirrors Heating is operated by pressing the Ü button. Heated rear window 3 31, Heated exterior mirrors 3 28. Demisting and defrosting the windows Air distribution to l. Set temperature control to warmest level. Set fan speed to highest level. Cooling n on. Press button V. Climate control system 3 103.
16 In brief Manual transmission automated Automatic transmission Starting off Check before starting off N o + A R = = = = = neutral position drive position higher gear lower gear switch between automatic and manual mode = reverse gear (with selector lever lock) Manual transmission automated 3 121.
In brief Starting the engine ■ Turn key to position 1 ■ move the steering wheel slightly to release the steering wheel lock ■ operate clutch and brake, if the clutch pedel is not operated the engine might not start and the control indicator - could illuminate ■ automatic transmission in P or N ■ do not operate accelerator pedal ■ diesel engines, turn the key to position 2 for preheating and wait until control indicator ! extinguishes ■ turn key to position 3 and release Starting the engine 3 112.
18 In brief Parking ■ Always apply the parking brake without pressing the release button. Apply as firmly as possible on a downhill slope or uphill slope. Depress the foot brake at the same time to reduce operating force. ■ Switch off the engine. Turn the ignition key to 0 and remove it. Turn the steering wheel until the steering wheel lock is felt to engage. For vehicles with automatic transmission, the key can only be removed when the selector lever is in the P position.
Keys, doors and windows Keys, doors and windows Keys, locks ................................... 19 Doors ........................................... 24 Vehicle security ............................ 25 Exterior mirrors ............................ 27 Interior mirrors ............................. 29 Windows ...................................... 29 Roof .............................................
20 Keys, doors and windows Radio remote control Used to operate: ■ Central locking system, ■ Anti-theft locking system, ■ Anti-theft alarm system, ■ Power windows. The radio remote control has an approximate range of up to 5 metres. This range can be affected by outside influences. The hazard warning flashers confirm operation. Handle with care, protect from moisture and high temperatures and avoid unnecessary operation.
Keys, doors and windows Extend the key and open the unit. Replace the battery (battery type CR 2032), paying attention to the installation position. Close the unit and synchronise. The saved settings are automatically used next time that key is used for unlocking. Key with fixed key section Have the battery replaced by a workshop. Unlocks and locks doors, load compartment and fuel filler flap. A pull on an interior door handle unlocks the entire vehicle and opens the door.
22 Keys, doors and windows Central locking system with radio remote control Locking Close doors, load compartment and fuel filler flap. If the driver's door is not closed properly, the central locking system will not work. Central locking system with radio remote control Central locking system with key activation Press button q. Two settings are possible: ■ To unlock only the driver's door, press button q once, to unlock the entire vehicle, press button q twice.
Keys, doors and windows Central locking button Fault in radio remote control Fault in central locking system Unlocking Unlocking Turn the key in the driver's door lock as far as it will go. The other doors can be opened by pulling the interior handle (not possible if the anti-theft locking system is active). The load compartment and fuel filler flap remain locked. To deactivate the antitheft locking system, switch on the ignition 3 25. Locking Press button m: the doors are locked or unlocked.
24 Keys, doors and windows Insert the key into the opening above the lock on the inside of the door and operate the lock by lifting until it clicks. Then close the door. The procedure must be carried out for each door. The driver's door can also be locked from the outside with the key. The fuel filler flap and tailgate cannot be locked.
Keys, doors and windows Notice The installation of certain heavy accessories onto the tailgate may affect its ability to remain open. Closing Vehicle security Anti-theft locking system 25 Activating with the remote control 9 Warning Do not use the system if there are people in the vehicle! The doors cannot be unlocked from the inside. Use the interior handle. Do not press the button under the moulding while closing as this will unlock the tailgate again. The system deadlocks all the doors.
26 Keys, doors and windows Light-emitting diode (LED) Seek the assistance of a workshop in the event of faults. Alarm During the first 10 seconds of antitheft alarm system activation: LED = Test, ignition delay, illuminates LED = Door, load flashes compartment or quickly bonnet open, or system fault. After the first 10 seconds of anti-theft alarm system activation: LED flashes = System active.
Keys, doors and windows Exterior mirrors Convex shape The convex exterior mirror contains an aspherical area and reduces blind spots. The shape of the mirror makes objects appear smaller, which will affect the ability to estimate distances. First select the relevant exterior mirror then use the control to adjust.
28 Keys, doors and windows Corsa VXR: For pedestrians safety, the exterior mirrors of the Corsa VXR are released from the holder if they are bumped. Fit mirror housing to holder with latching lugs and engage by striking gently. Manual Heated The exterior mirrors can be folded in by pressing gently on the outer edge of the housing. Operated by pressing the Ü button. Heating works with the engine running. It is switched off automatically after a short time.
Keys, doors and windows Interior mirrors Automatic anti-dazzle 29 Windows Windscreen Manual anti-dazzle Heat-reflecting windscreen The heat-reflecting windscreen has a coating which reflects solar radiation. Also data signals, e.g. from toll stations, might be reflected. Dazzle from following vehicles at night is automatically reduced. To reduce dazzle, adjust the lever on the underside of the mirror housing. The marked areas on the windscreen are not covered with the coating.
30 Keys, doors and windows Vignettes Do not attach vignettes or similar on the windscreen in the area of the interior mirror. Otherwise the detection zone of the sensor and the view area of the camera in the mirror housing could be restricted. Manual windows The door windows can be opened or closed with the window winders. Power windows 9 Warning Take care when operating the power windows. Risk of injury, particularly to children. Keep a close watch on the windows when closing them.
Keys, doors and windows Operating windows from outside Depending on the equipment level, the windows can be operated remotely from outside the vehicle. Press q or p until all windows have opened or closed. Overload If the windows are repeatedly operated at short intervals, the window operation is disabled for some time. Fault If the windows cannot be opened or closed automatically, activate the window electronics as follows: 1. Close doors. 2. Switch on ignition. 3.
32 Keys, doors and windows If the sun visors have integral mirrors, the mirror covers should be closed when driving. Roof Sunroof 9 Warning Take care when operating the sunroof. Risk of injury, particularly to children. Keep a close watch on the movable parts when operating them. Ensure that nothing becomes trapped in them as they move. Sunroof can be operated with ignition on. Operated via a rocker switch in the roof console. Press the button briefly for activation in steps.
Keys, doors and windows Caution When using a roof rack, check the free movement of the sunroof in order to avoid damage. It is only permitted to raise the sunroof when a roof rack is installed. Notice If the top of the roof is wet, tilt sunroof, allow water to run off and then open sunroof. Do not affix any stickers to sunroof. Close Hold down d until the sunroof is completely closed. Sunblind The sunblind is manually operated. Close or open the sunblind by sliding.
34 Seats, restraints Seats, restraints Head restraints ............................ 34 Front seats ................................... 35 Seat belts ..................................... 38 Airbag system .............................. 41 Child restraints ............................. 45 Head restraints Adjustment Head restraints on front seats Position 9 Warning Only drive with the head restraint set to the proper position. Press the button, adjust height and engage.
Seats, restraints Head restraints on rear seats Active head restraints In the event of a rear-end impact, the active head restraints tilt slightly forwards. The head is more effectively supported so the risk of whiplash injury is reduced. Notice Approved accessories may only be attached to the front passenger seat head restraint if the seat is not in use. The height of the head restraints can be set in two positions.
36 Seats, restraints ■ Sit with shoulders as far back against the backrest as possible. Set the backrest to an angle so that it is possible to reach the steering wheel with arms slightly bent. Maintain contact between shoulders and the backrest when turning the steering wheel. Do not tilt the backrest too far back. We recommend a maximum angle of approx. 25°. ■ Adjust the steering wheel 3 68. ■ Set the seat high enough to have a clear field of vision on all sides and on all display instruments.
Seats, restraints 37 Seat height Seat folding Corsa VXR Lever pumping motion up = higher down = lower Lift release lever and tilt backrest forwards. Lower release lever and backrest engages in lowered position. Slide seat forwards. To push the seat back to upright, it engages in its original position. Lift the release lever, move the backrest back to upright, lower lever, backrest engages. Folding the backrest forwards is possible only when the backrest is in an upright position.
38 Seats, restraints Heating Activate heating by pressing ß button for the seat with the ignition on. LED in button ß on: relevant front seat heating on. Seat heating is operational when the engine is running and during an Autostop. Seat belts The belts are locked during heavy acceleration or deceleration of the vehicle for the safety of the occupants. 9 Warning Fasten seat belt before each trip. In the event of an accident, people not wearing seat belts endanger their fellow occupants and themselves.
Seats, restraints Belt tensioners Triggered belt tensioners must be replaced by a workshop. Belt tensioners can only be triggered once. Notice Do not affix or install accessories or other objects that may interfere with the operation of the belt tensioners. Do not make any modifications to belt tensioner components as this will invalidate the vehicle type approval. In the event of a head-on or rear-end collision of a certain severity, the front seat belts are tightened.
40 Seats, restraints 9 Warning Removing seat belt Using the seat belt while pregnant The belt must not rest against hard or fragile objects in the pockets of your clothing. Height adjustment To release belt, press red button on belt buckle. Seat belts on the rear outer seats 1. Pull belt out slightly. 2. Press button. 3. Adjust height and engage audibly. Adjust the height so that the belt lies across the shoulder. It must not lie across the throat or upper arm. Do not adjust while driving.
Seats, restraints Airbag system The airbag system consists of a number of individual systems. When triggered the airbags inflate within milliseconds. They also deflate so quickly that it is often unnoticeable during the collision. 9 Warning If handled improperly the airbag systems can be triggered in an explosive manner. Notice The airbag systems and belt pretensioner control electronics are located in the centre console area. Do not put any magnetic objects in this area.
42 Seats, restraints Fit the seat belt correctly and engage securely. Only then the airbag is able to protect. Side airbag system The forward movement of the front seat occupants is decelerated, thereby considerably reducing the risk of injury to the upper body and head. 9 Warning Optimum protection is only provided when the seat is in the proper position 3 35. Keep the area in which the airbag inflates clear of obstructions.
Seats, restraints Curtain airbag system 43 Airbag deactivation Front airbag and side airbag systems for the front passenger seat have to be deactivated if a child restraint system is to be fitted on this seat. The curtain airbag system, the belt tensioners and all driver airbag systems will remain active. The curtain airbag system consists of an airbag in the roof frame on each side. This can be identified by the word AIRBAG on the roof pillars.
44 Seats, restraints 9 Danger Risk of fatal injury for a child using a child restraint system on a seat with activated front passenger airbag. Risk of fatal injury for an adult person on a seat with deactivated front passenger airbag. Control indicator W and LEDs in the button not on: Airbag systems for the front passenger are active. No child restraint systems can be installed.
Seats, restraints Control indicator for airbag deactivation 3 78. Starting the engine terminates changing of the setting. The setting can then only be changed once the ignition has been switched off and then back on again. Child restraints Child restraint systems When a child restraint system is being used, pay attention to the following usage and installation instructions and also those supplied with the child restraint system. Always comply with local or national regulations.
46 Seats, restraints Notice Do not stick anything on the child restraint systems and do not cover them with any other materials. A child restraint system which has been subjected to stress in an accident must be replaced.
Seats, restraints 47 Child restraint installation locations Permissible options for fitting a child restraint system On front passenger seat Weight and age class activated airbag deactivated airbag On rear outboard seats On rear centre seat Group 0: up to 10 kg or approx. 10 months X U1 U2 X Group 0+: up to 13 kg or approx. 2 years X U 1, 2 U2 X Group I: 9 to 18 kg or approx. 8 months to 4 years X U 1, 2 U2 X Group II: 15 to 25 kg or approx.
48 Seats, restraints Permissible options for fitting an ISOFIX child restraint system Weight class Size class Fixture On front passenger seat On rear outboard seats On rear centre seat Group 0: up to 10 kg E ISO/R1 IL IL X Group 0+: up to 13 kg E ISO/R1 IL IL X D ISO/R2 X X X C ISO/R3 X X X D ISO/R2 X X X C ISO/R3 X X X B ISO/F2 IL, IUF IL, IUF X B1 ISO/F2X IL, IUF IL, IUF X A ISO/F3 X X Group I: 9 to 18 kg IL X = Suitable for particular ISOFIX restrain
Seats, restraints ISOFIX size class and seat device A – ISO/F3 B – ISO/F2 B1 – ISO/F2X C – ISO/R3 D – ISO/R2 E – ISO/R1 = = = = = = Forward-facing child restraint system for children of maximum size in the weight class 9 to 18 kg. Forward-facing child restraint system for smaller children in the weight class 9 to 18 kg. Forward-facing child restraint system for smaller children in the weight class 9 to 18 kg. Rear-facing child restraint system for children of maximum size in the weight class up to 13 kg.
50 Seats, restraints Isofix child restraint systems Fasten vehicle-approved ISOFIX child restraint systems to the mounting brackets. When using ISOFIX mounting brackets for seat mounting, universally approved child restraint systems for ISOFIX may be used. ISOFIX mounting brackets are indicated by a label on the backrest. Closely follow the installation instructions accompanying the ISOFIX child restraint system.
Storage Storage Storage compartments 51 Cupholders Glovebox Storage compartments ................ 51 Load compartment ....................... 61 Roof rack system ......................... 65 Loading information ..................... 66 The glovebox features: ■ a card holder in cheque card format ■ a pen holder ■ pocket torch holder. The glovebox should be closed whilst driving. A cupholder is located in the front of the centre console.
52 Storage Underseat storage Rear carrier system Caution Do not attach bicycles with carbon pedal cranks to bicycle carriers. The bicycles might get damaged. Extending Open the tailgate. 9 Warning Lift at recessed edge and pull out. Maximum load: 1.5 kg. To close, push in and engage. The rear carrier system (Flex-Fix system) allows bicycles to be attached to a pull-out carrier integrated into the vehicle floor. The transportation of other objects is not permitted.
Storage Pull release lever up. The system disengages and travels quickly out of the bumper. 53 will not engage correctly, do not fit objects to the system and slide the system back. Seek the assistance of a workshop. Install the tail lamps Open out the lamp support on the back of the tail lamp completely until it engages. Completely pull out the rear carrier system until you hear it engage. Ensure that it is not possible to push in the rear carrier system without pulling the release lever again.
54 Storage Push the clamping lever down and push the lamp support into the retainer until it engages. Perform this procedure for both tail lamps. Check the cable and lamp position to make sure these are correctly installed and are securely located. Lock the rear carrier system Unfold pedal crank recesses Swivel the left clamping lever (1) first, followed by the right clamping lever (2) until they stop. Both clamping levers must point backwards, otherwise safe functionality is not guaranteed.
Storage 55 Adapting the rear carrier system to a bicycle Remove the pedal crank mounts from the pedal crank recesses. Press the release lever and withdraw the wheel recesses. Push the release lever on the strap retainer and remove the strap retainer.
56 Storage Prepare the bicycle for attachment Notice The maximum width for the pedal crank is 38.3 mm and the maximum depth is 14.4 mm. Rotate the left pedal (without a chain cog) vertically downwards. The pedal on the left pedal crank must be horizontal. The front bicycle must have its front wheel facing left. The rear bicycle must have its front wheel facing right.
Storage Put on the bicycle. The pedal crank here must be placed in the pedal crank recess opening as shown in the illustration. 57 Place the wheel recesses such that the bicycle is more or less horizontal. Here, the distance between the pedals and the tailgate should be at least 5 cm. Both bicycle tyres must be in the wheel recesses. Caution Make sure that the pedal does not touch the surface of the rear end carrier. Otherwise the crankset might be damaged during the transport.
58 Storage If the two bicycles obstruct one another, the relative positions of the bicycles can be adapted by adjusting the wheel recesses and the rotary lever on the pedal crank recess until the bicycles no longer touch one another. Make sure there is sufficient clearance from the vehicle. Caution Ensure gap between bicycle and vehicle is at least 5 cm. The settings for the wheel recesses and on the rotary lever on the pedal crank recess should be noted and saved for each bicycle.
Storage Retracting the rear carrier system 59 Press release lever and slide in wheel recesses all the way as far as they will go. Insert the strap retainer and pull tightly downwards as far as possible. Push the pedal crank mounts into the pedal crank recess as shown in the illustration. Disengage the locking lever on the diagonal support and fold both pedal crank recesses down. 9 Warning Risk of pinching.
60 Storage Push the clamping lever down and pull both lamp supports out of the recesses. Swivel first the right clamping lever (1) forwards, followed by the left clamping lever (2), until they can be engaged in their respective recesses. Fold in the lamp supports on the backs of the tail lamps. First place the front tail lamp (1), then the rear tail lamp (2) in the recesses and push down as far as possible. Push cables all the way into all guides in order to prevent damage. Open the tailgate.
Storage Load compartment Load compartment extension The rear backrest, in a single unit or split, can be locked in an upright position for transporting bulky items. Pull the release handle, pull the backrest forwards to the vertical position and engage. When unlocking, a red marking appears next to the release lever. The backrest is only engaged correctly when the red bolt is no longer protruding. 61 If the backrest is split, unlock the relevant side, and unlock at both sides if it is a single unit.
62 Storage 9 Warning Only drive the vehicle if the backrests are securely locked into position. Otherwise there is a risk of personal injury or damage to the load or vehicle in the event of heavy braking or a collision. Move rear seat backrests upright and allow locking mechanisms to engage audibly at both sides. Once the backrests are locked the red mark must no longer protrude. The rear seat backrests can be locked in two positions.
Storage 3-door passenger vehicle Lift the cover backwards until it unlatches, set at an angle, then remove. Fit in reverse order. Stowing When the load compartment is fully loaded, stow the load compartment cover behind the rear seat backrests: Lift the cover backwards until it unlatches, then slide down in guides behind the seat backrests. 63 Van The load compartment cover consists of four segments which can be individually removed and inserted.
64 Storage Rear floor storage cover The double load-bay floor can be inserted in the load compartment in two positions: ■ directly beneath the cover for the spare wheel recess or the floor cover, ■ or in the upper openings in the load compartment. To remove, lift the load-bay floor using the lever and pull backwards. To insert, push the load-bay floor forwards in the corresponding guide, then lower.
Storage Warning triangle First aid kit 65 Roof rack system Roof rack For safety reasons and to avoid damage to the roof, the vehicle approved roof rack system is recommended. Store warning triangle in rear load compartment wall: first fit warning triangle into recess on left and then insert in guide on right. To remove the warning triangle, lift to the right and pull out to the right. Stow the first-aid kit (cushion) in the compartment in the left wall of the load compartment.
66 Storage Fitting on model with sunroof Disengage covers concealing roof rack mounts by pushing sliders in direction of arrow (e.g. with a coin) and remove upwards. To close roof rack mounts, first insert covers at front and engage sliders at rear. Attach roof rack at appropriate points, see supplied roof rack system instructions. Loading information ■ Heavy objects in the load compartment should be placed against the seat backrests. Ensure the backrests are securely engaged.
Storage around inside the vehicle and cause personal injury or damage to the load or car. ■ The payload is the difference between the permitted gross vehicle weight (see identification plate 3 188) and the EC kerb weight. To calculate the payload weight, enter the data for your vehicle in the Weights table at the front of this manual. The EC kerb weight includes weights for the driver (68 kg), luggage (7 kg) and all fluids (tank 90 % full). Optional equipment and accessories increase the kerb weight.
68 Instruments and controls Instruments and controls Controls Steering wheel controls Steering wheel adjustment Controls ....................................... 68 Warning lights, gauges and indi‐ cators ........................................... 74 Information displays ..................... 83 Vehicle messages ........................ 87 Trip computer ............................... 89 Vehicle personalisation ................
Instruments and controls Heated steering wheel Activate heating in combination with the seat heating by pressing ß* button once or several times with the ignition on. LED ß on: driver seat heating on. LED ß and * on: driver seat heating and steering wheel heating on. LED * on: steering wheel heating on. Horn The steering wheel is heated in the areas shown in the illustration when the engine is running and during an Autostop. Press j.
70 Instruments and controls Windscreen wiper/washer Windscreen wiper The lever always springs back to its original position. & = fast % = slow $ = interval wiping § = off For a single wipe when the windscreen wiper is off, press the lever down. Run through the windscreen wiper stages by pushing the lever past the resistance point and holding it. An acoustic signal sounds at §. Do not use if the windscreen is frozen. Switch off in car washes.
Instruments and controls Pull lever. Washer fluid is sprayed onto the windscreen and the wiper wipes a few times. Rear window wiper/washer 71 The rear windscreen wiper comes on automatically when the windscreen wiper is switched on and reverse gear is engaged. Activation or deactivation of this function can be changed. Vehicle personalisation 3 93. Outside temperature Keep the sensor free from dust, dirt and ice. Windscreen washer Push lever forwards. The rear window wiper wipes in interval mode.
72 Instruments and controls icy road conditions. : remains illuminated until the temperature reaches at least 5 °C. Clock Date and time are shown in the Info-Display. Graphic-Info-Display, Color-Info-Display 3 84. Set date and time in Triple-Info-Display In vehicles with Graphic-Info-Display or Color-Info-Display, a warning message appears in the display as a warning for icy road conditions. There is no message below -5 °C.
Instruments and controls Power outlets The power outlet is located in the centre console. Caution Do not damage the outlet by using unsuitable plugs. Connecting electrical accessories while the engine is off will discharge the battery. Do not exceed the maximum power consumption of 120 Watts. Do not connect any 73 current-delivering accessories, e.g. electrical charging devices or batteries.
74 Instruments and controls The portable ashtray can be placed in the cupholders. Open cover to use. Warning lights, gauges and indicators Instrument cluster In some versions, the needles of the instruments briefly rotate to the end position when the ignition is switched on. Speed warning With the "Personalised key" function (P6), a particular maximum speed can be assigned to each vehicle key. When this speed is exceeded, a warning buzzer sounds. Vehicle personalisation 3 93.
Instruments and controls Trip odometer The top line displays the recorded distance since the last reset. To reset, hold the reset knob depressed for a few seconds with the ignition on. Tachometer Displays the engine speed. Drive in a low engine speed range for each gear as much as possible. Upshift when indicated by the control indicator [ 3 80. Caution If the needle is in the red warning zone, the maximum permitted engine speed is exceeded. Engine at risk.
76 Instruments and controls 1 off = petrol operation 1 illuminates = liquid gas operation 1 flashes = no switching is possible, one type of fuel is empty The message InSP appears when it is time for servicing. Further information 3 184.
Instruments and controls Control indicators in the instrument 77
78 Instruments and controls Turn signal O illuminates or flashes green. Illuminates The control indicator illuminates briefly when the parking lights are switched on 3 99. Flashes The control indicator flashes if a turn signal or the hazard warning flashers are activated. Rapid flashing: failure of a turn signal light or associated fuse, failure of turn signal light on trailer. Bulb replacement 3 149, Fuses 3 161, Turn signals 3 98. Seat belt reminder X illuminates or flashes red.
Instruments and controls Illuminates when the engine is running Stop, switch off engine. Battery is not charging. Engine cooling may be interrupted. In diesel engines, power to the brake servo unit may be cut. Seek the assistance of a workshop. Flashes during or after engine start Flashes when the engine is running Fault that could lead to catalytic converter damage. Ease up on the accelerator until the flashing stops. Seek the assistance of a workshop immediately.
80 Instruments and controls On vehicle with automated manual transmission, R flashes for a few seconds when the ignition is switched off if the parking brake is not applied. On vehicles with automated manual transmission, R flashes when the driver's door is opened if no gear is engaged and the parking brake is not applied. Apply clutch pedal ABS. The brake system remains operational but without ABS regulation. Anti-lock Braking System 3 125.
Instruments and controls Illuminates for a few seconds when the ignition is switched on. Flashing during driving The system is actively engaged. Engine output may be reduced and the vehicle may be braked automatically to a small degree 3 127. Illuminates while driving The system is switched off or a fault is present. Continued driving is possible. Driving stability, however, may deteriorate depending on road surface conditions. Have the cause of the fault remedied by a workshop.
82 Instruments and controls Illuminates when the engine is running Caution Do not remove key until vehicle is stationary, otherwise the steering wheel lock could engage unexpectedly. Engine lubrication may be interrupted. This may result in damage to the engine and/or locking of the drive wheels. Check oil level before seeking the assistance of a workshop 3 144. 1. Depress clutch. 2. Select neutral gear, set selector lever to N. 3.
Instruments and controls Adaptive forward lighting B illuminates yellow. Illuminates when the engine is running Fault in system. Seek the assistance of a workshop. Illuminates after ignition is switched on Control indicator B illuminates for approx. 4 seconds as a functionality test. Control indicator B illuminates for approx. 8 seconds as a reminder that the headlights have been set to symmetrical low beam 3 97. Fog light > illuminates green. Illuminated when the front fog lights are on 3 99.
84 Instruments and controls Graphic-Info-Display, Colour-Info-Display Selecting functions Functions and settings of the Infotainment system and electronic climate control system are accessed via the display. Selections are made via the menus and buttons or the left adjuster wheel of the steering wheel. To exit a menu, press the right or left arrow button until Return or Main appear and select.
Instruments and controls 85 Function areas System settings Setting date and time For each function area there is a main page (Main), which is selected at the top edge of the display (only with trip computer and Mobile Phone Portal): ■ Audio, ■ Telephone, ■ Trip computer. Press the Settings button on the Infotainment system. For Infotainment system CD 30, no menu may be selected. Select menu item Time, Date from the Settings menu. Select the required menu items and make settings.
86 Instruments and controls Setting units of measure Some transmitters do not send a correct time signal. In such cases, we recommend to switch off automatic time synchronisation. The function is activated by highlighting the field in front of Synchron. clock automatical. in the Time, Date menu. Language selection Selection is indicated by a 6 in front of the menu item.
Instruments and controls Adjusting contrast (Graphic-Info-Display) Always day design black or coloured text on light background. Always night design white or coloured text on dark background. Selection is indicated by a o in front of the menu item. Ignition logic See Infotainment system manual. Smartphone controller Select menu item Contrast from the Settings menu. Confirm the required setting. Setting display mode Display brightness is dependent on vehicle lighting.
88 Instruments and controls engine is running, a gear is engaged and the foot brake is not depressed. ■ Warning signal sounds three times if the rear carrier system is extended and reverse gear is selected. When the vehicle is parked and the driver's door is opened ■ When the key is in the ignition switch. ■ With exterior lights on. ■ For automated manual transmission, if the parking brake is not applied and no gear is engaged when the engine is switched off.
Instruments and controls Trip computer The trip computer provides information on driving data, which is continually recorded and evaluated electronically. 89 Range Range is calculated from current fuel tank content and current consumption. The display shows average values. After refuelling, the range is updated automatically after a brief delay. When the fuel level in the tank is low, a message appears on the display. Confirm the warning message by pressing 7 on the wiper lever.
90 Instruments and controls Average consumption Display of average consumption. The measurement can be reset at any time. Stop watch Measurement of the time from activation to deactivation. Press the 7 button to start and stop the measurement. Reset trip computer The measurement or calculation of the following trip computer information can be restarted: ■ Distance, ■ Average speed, ■ Absolute consumption, ■ Average consumption. Select the desired function.
Instruments and controls 91 Absolute consumption Displays fuel consumed. The measurement can be reset at any time. Average consumption Displays average consumption. The measurement can be reset at any time. Restart trip computer When the fuel level in the tank is low, the message Range appears in the display. When the fuel tank is nearly empty, the message Please refuel! appears in the display. Instantaneous consumption Displays the instantaneous consumption.
92 Instruments and controls Stop watch The information of the two trip computers can be reset separately, making it possible to evaluate data from different time periods. Select the required trip computer information and confirm. To reset all information of a trip computer, select menu item All values. Select menu item Stop Watch from the Board Computer menu. To start, select menu item Start. To stop, select menu item Stop. To reset, select menu item Reset.
Instruments and controls Driving Time incl. Stops The time the vehicle is in motion is recorded. The time the vehicle is stationary with the ignition switched on is included. Travel Time Measurement of the time from manual activation via Start to manual deactivation via Reset. 93 Vehicle personalisation The vehicle-specific functions P1 to P7 can be activated and deactivated. The setting selected is automatically stored depending on the vehicle key used.
94 Instruments and controls ■ Push the turn signal stalk (left) up or down and select the desired function P1 - P7. ■ Push the wiper stalk (right) up or down and select status On or OFF, or input a value for speed (P6) or value for volume (P7). ■ Pull turn signal stalk (left) and wiper stalk (right) simultaneously to the steering wheel until you hear a confirmation signal (approx. 3 seconds). The selected settings are now stored for the key in the ignition switch.
Lighting Lighting Exterior lighting Light switch Exterior lighting ............................ 95 Interior lighting ........................... 100 Lighting features ........................ 102 8 9 = sidelights = low beam When switching on the ignition, automatic light control is active. Control indicator 8 3 82. Tail lights Tail lights are illuminated together with low beam and sidelights.
96 Lighting Automatic light control function When the automatic light control function is switched on and the engine is running, the system switches between daytime running light and low beam in dependence of lighting conditions. High beam Headlight range adjustment Manual headlight range adjustment Daytime running light Daytime running light increases visibility of the vehicle during daylight. Tail lights are not on.
Lighting 0 = Front seats occupied 1 = All seats occupied 2 = All seats occupied and load compartment laden 3 = Driver's seat occupied and load compartment laden Headlights when driving abroad The asymmetrical headlight beam extends visibility at the edge of the road at the passenger side. However, when driving in countries where traffic drives on the opposite side of the road, adjust the headlights to prevent dazzling of oncoming traffic.
98 Lighting Reversing function If the lights are on, reverse gear is engaged, and the turn signal is activated, the cornering light on the appropriate side is switched on. The cornering light stays on for 15 seconds once the turn signal has been switched off. Control indicator B 3 83. Turn and lane-change signals Acoustic turn signal Hazard warning flashers The volume of the acoustic turn signal can be adjusted. This function can be programmed depending on the key used 3 93.
Lighting 99 Front fog lights Rear fog lights Parking lights Operated with the > button. Light switch in position AUTO: switching on front fog lights will switch the low beam on automatically. Operated with the r button. Light switch in position AUTO: switching on front fog lights will switch the low beam on automatically. The rear fog light can only be switched on when both the ignition and the low beam or sidelights (with front fog lights) are on.
100 Lighting Reversing lights The reversing lights come on when the ignition is on and reverse gear is selected. Interior lighting Instrument panel illumination control Misted light covers Interior lights During entry and exit of the vehicle, the front and centre courtesy lights automatically come on and then switch off after a delay. Front courtesy light The inside of the light covers may mist up briefly in poor, wet and cold weather conditions, in heavy rain or after washing.
Lighting Front courtesy light with reading lights Operated with the c button when the doors are closed. 101 Rear courtesy lights Reading lights Operated with switch. I = On 0 = Off centre = automatic Operated with a buttons with ignition on. Load compartment lighting The lighting switches on when opened.
102 Lighting Lighting features Centre console lighting Spotlight in interior mirror housing. Daylight-dependent, automatically regulated centre console lighting. Entry lighting After unlocking the vehicle, the instrument panel lighting, the front and rear foot well lighting and the information display come on for a few seconds. Starting off 3 16. Peripheral lighting The exterior lights come on for approx. 30 seconds.
Climate control Climate control Climate control systems ............. 103 Air vents ..................................... 109 Maintenance .............................. 110 Climate control systems Heating and ventilation system 103 Heating will not be fully effective until engine has reached normal operating temperature. Fan speed Adjust the air flow by switching the fan to the desired speed.
104 Climate control ■ Open side air vents as required and direct them towards door windows. ■ For simultaneous warming of the foot well, set air distribution control to J. Air conditioning system Notice If the settings for demisting and defrosting are selected, an Autostop will be inhibited. If the settings for demisting and defrosting are selected while the engine is in an Autostop, the engine will restart automatically. Stop-start system 3 113.
Climate control 9 Warning The exchange of fresh air is reduced in air recirculation mode. In operation without cooling the air humidity increases, so the windows may mist up from inside. The quality of the passenger compartment air deteriorates, which may cause the vehicle occupants to feel drowsy. ■ Set temperature control to coldest level. ■ Set fan speed to highest level. ■ Set air distribution control to M. ■ Open all vents.
106 Climate control Temperature preselection Controls for: ■ Temperature ■ Air distribution and menu selection ■ Fan speed AUTO = Automatic mode = Air recirculating 4 = Demisting and defrosting V Heated rear window Ü 3 31. The preselected temperature is automatically regulated. In automatic mode, the fan speed and air distribution automatically regulate the air flow. The system can be manually adapted with the air distribution and air flow controls. Data is shown on the Info-Display.
Climate control To return to automatic mode: Press AUTO button. Demisting and defrosting the windows Press the V button. V appears in the display. Temperature and air distribution are set automatically and the fan runs at a high speed. To return to automatic mode: Press button V or AUTO. Switch on heated rear window Ü. Notice If the V button is pressed with fan switched on while the engine is running, an Autostop will be inhibited until the V button is pressed again.
108 Climate control If no cooling or drying is required, deactivate AC to save fuel. When the cooling system is switched off, no engine restart will be requested by the climate control system during an Autostop. Depending on the vehicle equipment, the display will indicate AC when cooling is activated or Eco when the cooling is deactivated. On vehicles with stop-start system, two settings for the operation of the climate control system during an Autostop are available. Select menu item ecoMode.
Climate control Auxiliary heater Air vents Air heater Adjustable air vents Quickheat is an electric auxiliary air heater which automatically warms up the passenger compartment more quickly. 109 At least one air vent must be open while cooling is on in order to prevent the evaporator from icing up due to lack of air movement. Coolant heater Diesel-engined vehicles have a fuelpowered auxiliary heater. To close the vent, turn the adjuster wheel to left or right to its stop.
110 Climate control Maintenance Air intake Air conditioning regular operation In order to ensure continuously efficient performance, cooling must be operated for a few minutes once a month, irrespective of the weather and time of year. Operation with cooling is not possible when outside temperature is too low. Service The air intake in front of the windscreen in the engine compartment must be kept clear to allow air intake. Remove any leaves, dirt or snow.
Driving and operating Driving and operating Driving hints ............................... 111 Starting and operating ............... 111 Engine exhaust .......................... 115 Automatic transmission .............. 117 Manual transmission .................. 120 Manual transmission automa‐ ted .............................................. 121 Brakes ........................................ 125 Ride control systems ................. 127 Cruise control .............................
112 Driving and operating Ignition switch positions Starting the engine During an Autostop, the engine can be started by depressing the clutch pedal. Starting the vehicle at low temperatures 0 = Ignition off 1 = Steering wheel lock released, ignition off 2 = Ignition on, for diesel engine: preheating 3 = Starting Operate clutch and brake, if the clutch pedel is not operated the engine might not start and the control indicator - could illuminate. Automatic transmission in P or N.
Driving and operating Overrun cut-off 113 Deactivation The fuel supply is automatically cut off during overrun, i.e. when the vehicle is driven with a gear engaged but accelerator is released. Overrun cutoff is deactivated if catalytic converter temperature is high. Stop-start system The stop-start system helps to save fuel and to reduce the exhaust emissions. When conditions allow, it switches off the engine as soon as the vehicle is at a low speed or at a standstill, e.g.
114 Driving and operating ■ the battery is sufficiently charged and in good condition ■ the engine is warmed up ■ the engine coolant temperature is not too high ■ the engine exhaust temperature is not too high, e.g.
Driving and operating ■ the climate control system requests an engine start ■ the air conditioning is manually switched on If the bonnet is not fully closed, a warning message is displayed in the Driver Information Centre. If an electrical accessory, e.g. a portable CD player, is connected to the power outlet, a brief power drop during restart might be noticeable. Parking ■ Do not park the vehicle on an easily ignitable surface. The high temperature of the exhaust system could ignite the surface.
116 Driving and operating consumption may be higher during this period. The emission of smells and smoke during this process is normal. Stopping the journey or switching off the engine during cleaning is not recommended. Under certain driving conditions, e.g. short distances, the system cannot clean itself automatically. If the filter requires cleaning and previous driving conditions did not enable automatic cleaning, control indicator ! flashes. Continue driving, keeping engine speed above 2000 rpm.
Driving and operating Caution Fuel grades other than those listed on pages 3 130, 3 193 could damage the catalytic converter or electronic components. Unburnt petrol will overheat and damage the catalytic converter. Therefore avoid excessive use of the starter, running the fuel tank dry and starting the engine by pushing or towing.
118 Driving and operating The engine can only be started with lever in position P or N. When position N is selected, press brake pedal or apply parking brake before starting. Do not accelerate while engaging a gear. Never depress the accelerator pedal and brake pedal at the same time. When a gear is engaged, the vehicle slowly begins to creep when the brake is released. Gears 3, 2, 1 3, 2, 1 = Transmission does not shift above the selected gear. Press button on selector lever to engage 3 or 1.
Driving and operating Activation Press the T button with P, R, N, D or 3 engaged. The vehicle starts off in 3rd gear. If the accelerator pedal is pressed past the pressure point, the transmission shifts to a lower gear depending on engine speed. Deactivation The Winter programme is switched off by: ■ pressing the T button again, ■ manually selecting 2 or 1, ■ turning off the ignition, ■ or if the transmission oil temperature is too high. Fault Kickdown In the event of a fault, A illuminates.
120 Driving and operating Manual transmission Caution It is not advisable to drive with the hand resting on the selector lever. 3. Push the yellow catch forward with a screwdriver and move the selector lever out of P. If P is engaged again, the selector lever will be locked in position again. Have the cause of the power supply interruption remedied by a workshop. 4. Mount selector lever trim on centre console and refit.
Driving and operating Manual transmission automated This transmission permits manual (manual mode) or automatic gear shifting (automatic mode), both with automatic clutch control. Transmission display Starting the engine Depress the foot brake when starting the engine. If the foot brake is not depressed, j illuminates in the instrument cluster, "N" flashes in the transmission display and the engine cannot be started. Starting is not possible if all brake lights fail.
122 Driving and operating If neither the accelerator nor the brake pedal are depressed, no gear is engaged and A or R flashes for a brief time in the display. Stopping the vehicle In A, first gear is engaged and the clutch is released when the vehicle is stopped. In R, reverse gear remains engaged. Engine braking Automatic mode When driving downhill, the manual transmission automated does not shift into higher gears until a fairly high engine speed has been reached.
Driving and operating Sport mode Deactivation The Sport mode is switched off by: ■ pressing the S button again ■ turning off the ignition, ■ activating the winter mode T. Winter mode T Shift times are reduced when the Sport mode is enabled, and the gears are shifted at higher engine speeds, although not when cruise control is activated. Activation Press the S button. Control indicator 1 3 80. Activate the Winter mode if you have problems starting off on a slippery road surface.
124 Driving and operating Kickdown If F appears in the transmission display, continued driving is not possible. Have the cause of the fault remedied by a workshop. Interruption of power supply If the accelerator pedal is pressed past the pressure point, the transmission shifts to a lower gear depending on engine speed. Fault To prevent damage to the manual transmission automated, the clutch is engaged automatically at high clutch temperatures. A illuminates in the event of a fault.
Driving and operating 5. Using a flat-head screwdriver, turn the adjusting screw under the cap clockwise until clear resistance can be felt. The clutch has now been disengaged. 6. Refit cleaned cap. The cap must be in full contact with the housing. Caution Do not turn beyond the resistance since this could damage the transmission. Caution Towing the vehicle and starting the engine is not permitted when the clutch has been disengaged in this way, although the vehicle can be moved a short distance.
126 Driving and operating Parking brake Fault If the brake pedal is depressed quickly and forcefully, maximum brake force is automatically applied (full braking). Maintain steady pressure on the brake pedal for as long as full braking is required. Maximum brake force is automatically reduced when the brake pedal is released. 9 Warning If there is a fault in the ABS, the wheels may be liable to lock due to braking that is heavier than normal. The advantages of ABS are no longer available.
Driving and operating Ride control systems Electronic stability program Electronic stability program (ESP®Plus) improves driving stability when necessary, regardless of the type of road surface or tyre grip. It also prevents the drive wheels from spinning. As soon as the vehicle starts to swerve (understeer/oversteer), engine output is reduced and the wheels are braked individually. This considerably improves the driving stability of the vehicle on slippery road surfaces.
128 Driving and operating Cruise control The cruise control can store and maintain speeds of approx. 20 to 120 mph. Deviations from the stored speeds may occur when driving uphill or downhill. For safety reasons the cruise control cannot be activated until the foot brake has been operated once. With automatic transmission or manual transmission automated, only activate cruise control in automatic mode. Control indicator m 3 83.
Driving and operating Object detection systems Parking assist Notice Attached parts in the detection area cause system malfunction. Activation When reverse gear is engaged, the system switches itself on automatically. An obstacle is indicated by buzzers. The interval between the buzzers becomes shorter as the vehicle gets closer to the obstacle. When the distance is less than 30 cm, the buzzer is continuous.
130 Driving and operating Fuel Fuel for petrol engines Only use unleaded fuel that complies with European standard EN 228 or E DIN 51626-1 or equivalent. Your engine is capable to run with E10 fuel that fulfills these standards. E10 fuel contains up to 10 % bioethanol. Use fuel with the recommended octane rating 3 193. Use of fuel with too low an octane rating can reduce engine power and torque and slightly increases fuel consumption.
Driving and operating The boiling point depends on the pressure and mixing ratio. At ambient pressure, it is between -42 °C (pure propane) and -0.5 °C (pure butane). Caution The system works at an ambient temperature of approx. -8 °C to 100 °C. Full function of the LPG system can only be guaranteed with liquid gas which complies with the minimum requirements of DIN EN 589.
132 Driving and operating Refuelling Caution Repairs and adjustments may only be made by trained specialists in order to maintain the safety and warranty on the LPG system. Liquid gas is given a particular odour (odorised) so that any leaks can be detected easily. 9 Warning If you smell gas in the vehicle or in the immediate vicinity, switch to petrol mode immediately. No smoking. No naked flames or ignition sources. If possible, close the manual shut-off valve on the multivalve.
Driving and operating To close, turn the fuel filler cap to the right until it clicks. Close the flap and let engage. 9 Danger Fuel is flammable and explosive. No smoking. No naked flames or sparks. If you can smell fuel in your vehicle, have the cause of this remedied immediately by a workshop. Caution In case of misfuelling, do not switch on ignition. Fuel filler flap is located at right rear side of vehicle.
134 Driving and operating Fit the required adapter. ACME Adapter: Screw the nut of the filling nozzle onto the adapter. Press locking lever on filler nozzle down. DISH (Italy) filler neck: Place the filler nozzle into the adapter. Press locking lever on filler nozzle down. Bayonet filler neck: Place filler nozzle on the adapter and turn to the left or right through one quarter turn. Pull locking lever of filler nozzle fully. EURO filler neck: Press the filler nozzle onto the adapter until it engages.
Driving and operating 135 Croatia, Latvia, Lithuania, Macedonia, Austria, Poland, Portugal, Romania, Sweden, Switzerland, Serbia, Slovakia, Slovenia, Czech Republic, Turkey, Ukraine, Hungary Fuel filler cap Only use genuine fuel filler caps. Diesel-engined vehicles have special fuel filler caps.
136 Driving and operating General information The official fuel consumption and specific CO2 emission figures quoted relate to the EU base model with standard equipment. Fuel consumption data and CO2 emission data are determined according to regulation R (EC) No. 715/2007 (in the version respectively applicable), taking into consideration the vehicle weight in running order, as specified by the regulation.
Driving and operating The permissible trailer loads are specified in the vehicle documents. In general, they are valid for gradients up to max. 12 % The permitted trailer loads apply up to the specified incline and up to an altitude of 1000 metres above sea level. Since engine power decreases as altitude increases due to the air becoming thinner, therefore reducing climbing ability, the permissible gross train weight also decreases by 10 % for every 1000 metres of additional altitude.
138 Driving and operating Push both bolts inwards and remove the cover on the bumper. Checking the tensioning of the coupling ball bar Disengage and fold down the socket. Remove the sealing plug from the opening for the coupling ball bar and stow it. ■ The rotary knob rests on the coupling ball bar. ■ Green marking on the rotary knob is not visible. ■ Locking pin at the top of the coupling ball bar is set inwards. ■ The key is in the lock.
Driving and operating 139 Inserting the coupling ball bar ■ Place the key in the lock and unlock the coupling ball bar. ■ Push the rotary knob onto the coupling ball bar and rotate right while pressed down until it engages. The key remains in the lock. Insert the tensioned coupling ball bar in the opening and push firmly upwards until it audibly engages. The rotary knob snaps back into its original position resting against the coupling ball bar without a gap.
140 Driving and operating Eye for break-away stopping cable Attach breakaway stopping cable to eye. Check that the coupling ball bar is correctly installed ■ Green marking on rotary knob is visible. ■ There must be no gap between the rotary knob and the coupling ball bar. ■ The coupling ball bar must be firmly engaged in the opening. ■ The coupling ball bar must be locked and the key removed. 9 Warning Towing a trailer is permitted only when a coupling ball bar is fitted correctly.
Vehicle care Vehicle care General Information ................... 141 Vehicle checks ........................... 142 Bulb replacement ....................... 149 Electrical system ........................ 161 Vehicle tools .............................. 165 Wheels and tyres ....................... 167 Jump starting ............................. 176 Towing ....................................... 178 Appearance care .......................
142 Vehicle care ■ Open bonnet, close all doors and lock the vehicle. ■ Disconnect the clamp from the negative terminal of the vehicle battery. Beware that all systems are not functional, e.g. anti-theft alarm system. Putting back into operation Following must be done if the vehicle is putting back into operation: ■ Connect the clamp to the negative terminal of the vehicle battery. Activate the electronics of the power windows. ■ Check tyre pressure. ■ Fill up the washer fluid reservoir.
Vehicle care 9 Danger 143 Pull the release lever and return it to its original position. The ignition system and Xenon headlights use extremely high voltage. Do not touch. The caps for topping up the engine oil, the coolant, the washing fluid and the oil dipstick handle are yellow for ease of identification. Bonnet Opening Lift the safety catch upwards and open the bonnet. Air intake 3 110. Secure the bonnet support.
144 Vehicle care Engine oil Check the engine oil level manually on a regular basis to prevent damage to the engine. Ensure that the correct specification of oil is used. Recommended fluids and lubricants 3 185. Check with the vehicle on a level surface. The engine must be at operating temperature and switched off for at least 5 minutes. Pull out the dipstick, wipe it clean, insert it to the stop on the handle, pull out and read the engine oil level.
Vehicle care Engine coolant The coolant provides freeze protection down to approx. -28 °C. Caution Only use approved antifreeze. Coolant level Caution Too low a coolant level can cause engine damage. If the cooling system is cold, the coolant level should be above the KALT/COLD mark. Top up if the level is low. 145 Washer fluid 9 Warning Allow the engine to cool before opening the cap. Carefully open the cap, relieving the pressure slowly. Top up with antifreeze.
146 Vehicle care Brakes Battery A squealing noise indicates that the brake lining is at its minimum thickness. Continued driving is possible but have the brake lining replaced as soon as possible. Once new brake linings are installed, do not brake unnecessarily hard for the first few journeys. The vehicle battery is maintenancefree provided that the driving profile allows sufficient charging of the battery. Short distance driving and frequent engine starts can discharge the battery.
Vehicle care The anti-theft alarm siren must be deactivated as follows: switch the ignition on then off, disconnect the vehicle's battery within 15 seconds. Warning label ■ The battery contains sulfuric acid which could cause blindness or serious burn injuries. ■ See the Owner's Manual for further information. ■ Explosive gas may be present in the vicinity of the battery. 147 In vehicles with an AGM (Absorptive Glass Mat) battery, ensure to have the battery replaced with an AGM battery.
148 Vehicle care Stop-start system 3 113. Wiper blade replacement Charging the battery Service setting for front windscreen wipers 9 Warning Wiper blades on the windscreen On vehicles with an AGM battery, ensure that the charging potential does not exceed 14.6 volts when using a battery charger. Otherwise the battery might be damaged. Jump starting 3 176. Diesel fuel system bleeding If the tank has been run dry, the diesel fuel system must be bled.
Vehicle care Wiper blade on the rear window Bulb replacement Switch off the ignition and switch off the relevant switch or close the doors. Only hold a new bulb at the base! Do not touch the bulb glass with bare hands. Use only the same bulb type for replacement. 149 To replace the bulb on the left-hand side, remove fuse box cover 3 163, and also remove windscreen washer system reservoir filler neck from above. Washer fluid may escape if the reservoir is full to the top.
150 Vehicle care Low beam 1. Disengage wire clip and remove protective cover 1. 2. Press base to the side and remove bulb from reflector. 3. Detach plug connector from bulb. 4. Insert new bulb in reflector so that the locating tab of the bulb holder aligns with the reflector recess. 5. Engage bulb. 6. Attach connector to bulb. 7. Put on protective cover and engage wire clip. High beam 1. Rotate protective cover 2 anticlockwise and remove. 2. Detach wiring plug from bulb.
Vehicle care 151 4. Remove bulb from reflector housing. 5. When installing the new bulb, insert lugs in the reflector recesses. 6. Install spring clip, plug connector onto bulb. 7. Install protective cover. Daytime running light/Side light 3. Disengage spring clip from retainer by moving and swivelling to the side. 2. Remove bulb from socket, insert new bulb. 3. Insert bulb holder in reflector so that the locating tab of the bulb holder aligns with the reflector recess. 4. Rotate clockwise to engage.
152 Vehicle care Adaptive forward lighting Headlights have separate systems for low and high beam 1 (outer bulb), cornering light 2 (inner bulb) and daytime running light/side light 3. Low/high beam 2. Rotate bulb holder anticlockwise to disengage. Withdraw bulb holder from reflector. 1. Disengage wire clip and remove protective cover 1. 3. Insert new bulb in reflector so that the locating tab of the bulb holder aligns with the reflector recess. 4. Engage bulb holder by turning clockwise. 5.
Vehicle care Cornering light Daytime running light/Side light 1. Rotate bulb holder 3 anticlockwise to disengage. Withdraw bulb holder from reflector. 2. Remove bulb from socket, insert new bulb. 3. Insert bulb holder in reflector so that the locating tab of the bulb holder aligns with the reflector recess. 4. Rotate clockwise to engage. 1. Rotate protective cover 2 anticlockwise and remove.
154 Vehicle care 2. Detach wiring plug from bulb. 3. Disengage spring clip from retainer by moving and swivelling to the side. 4. Remove bulb from reflector housing. 5. When installing the new bulb, insert lugs in the reflector recesses. 6. Install spring clip, plug connector onto bulb. 7. Install protective cover. Front turn signal light 2. Rotate bulb holder anticlockwise to disengage. Withdraw bulb holder from reflector. 1. Disengage wire clip and remove protective cover 1. 3.
Vehicle care Fog lights Tail lights The bulbs are accessible from the underside of the vehicle. 5-door passenger vehicle 1. Turn the bulb holder anticlockwise and remove it from the reflector. 2. Disengage the bulb holder from the plug connector by pressing the retaining lug. 3. Remove and replace the bulb holder with bulb. 4. Attach the plug connector. 5. Insert the bulb holder into the reflector. 6. Turn the bulb holder clockwise and engage. 155 1. Open side cover.
156 Vehicle care 5. Gently press the three locking lugs on the outside of the bulb holder outwards and remove bulb holder. 2. Remove plug connector by pressing on bulb holder tab. 3. Hold bulb housing from the outside; unscrew two retaining nuts. 4. Detach bulb housing towards the rear. 6. Push bulb into socket slightly, rotate anti-clockwise, remove and renew bulb.
Vehicle care 3-door passenger vehicle, van 7. Engage bulb holder in bulb housing, ensuring that it properly engages. 8. Ensure that the bulb holder seal is positioned as illustrated. 157 9. Insert bulb housing in vehicle body, tighten securing nuts by hand. Engage plug connector. Close cover. After bulb replacement, check the tail lights for proper functionality: switch on the ignition, operate the brake, switch on the sidelights. 1. Open side cover.
158 Vehicle care 5. Gently press the three locking lugs on the outside of the bulb holder outwards and remove bulb holder. 2. Remove plug connector by pressing on bulb holder tab. 3. Hold bulb housing from the outside; unscrew two retaining nuts. 4. Remove tail light assembly. 6. Push bulb into socket slightly, rotate anti-clockwise, remove and renew bulb.
Vehicle care 7. Engage bulb holder in bulb housing, ensuring that it properly engages. 159 Side turn signal lights Have bulbs replaced by a workshop. Number plate light 8. Ensure that the bulb holder seal is positioned as illustrated. Fit the round seal on the fastening bolt. 9. Insert bulb housing in vehicle body, and tighten securing nuts by hand. Engage plug connector. Close and lock cover.
160 Vehicle care Interior lights Front courtesy light 4. Rotate bulb holder anti-clockwise to disengage. 5. Remove bulb from holder and renew bulb. 6. Insert bulb holder in bulb housing and rotate clockwise. 7. Connect wiring plug to bulb holder. 8. Insert and engage bulb housing. 1. Disengage and remove lens at the position located in the illustration using a screwdriver. 2. Remove bulb from socket. 3. Insert new bulb. 4. Mount lens and engage in position. Front courtesy light, reading lights 1.
Vehicle care Glovebox light, foot well light 1. Prise the lamp out with a screwdriver. 2. Press bulb slightly towards spring clip and remove. 3. Insert new bulb. 4. Install lamp. 161 Electrical system Fuses Data on the replacement fuse must match the data on the defective fuse.
162 Vehicle care Engine compartment fuse box The fuse box is in the front left of the engine compartment. Disengage the cover, lift it upwards and remove.
Vehicle care No. Circuit No. Circuit No.
164 Vehicle care No. Circuit 10 Electrical power steering 11 Light switch, brake light 12 ABS, brake light 13 Heated steering wheel 14 Parking assist, rain sensor, inte‐ rior mirror In right-hand drive vehicles, the fuse box is located behind a cover in the glovebox. Open the glovebox and remove the cover. To close, first put on the cover, then lock it into position. No.
Vehicle care The fuse box is on the left side of the load compartment behind a cover. Remove the cover. No. Circuit Vehicle tools 7 – 8 Rear carrier system, towing equipment Tools 9 – 165 10 – 11 – 12 – 13 – 14 – No. Circuit 15 Rear carrier system, towing equipment 1 Adaptive forward lighting 16 – 2 – 17 Sunroof 3 Seat heater (left) 4 Seat heater (right) 5 – 6 – To open the compartment, disengage the cover and open it.
166 Vehicle care Vehicles with tyre repair kit Vehicles with spare wheel Variant 1: The jack and the vehicle tools are in the load compartment underneath the spare wheel. A label on the jack indicates the vehicles for which the jack can be used. Variant 2: The jack and the vehicle tools are in the right-hand compartment in the load compartment. The vehicle tools are in the right-hand compartment in the load compartment, together with the tyre repair kit.
Vehicle care Wheels and tyres Tyre condition, wheel condition Drive over edges slowly and at right angles if possible. Driving over sharp edges can cause tyre and wheel damage. Do not trap tyres on the kerb when parking. Regularly check the wheels for damage. Seek the assistance of a workshop in the event of damage or unusual wear. Tyres Tyres of size 185/60 R 15 are only approved as winter tyres. Tyres of size 185/65 R 15 are only approved as winter tyres on vehicles with a sports chassis.
168 Vehicle care 9 Warning System initialisation If the pressure is too low, this can result in considerable tyre warmup and internal damage, leading to tread separation and even to tyre blow-out at high speeds. Tyre deflation detection system Tyre pressure 3 209 and on the label on the inside of the fuel filler flap or on the front right door frame. The tyre pressure data refers to cold tyres. It applies to summer and winter tyres. Always inflate the spare tyre to the pressure specified for full load.
Vehicle care For safety reasons it is recommended that the tread depth of the wheels on one axle should not vary by more than 2 mm. Tyres age, even if they are not used. We recommend tyre replacement every 6 years. Changing tyre and wheel size If tyres of a different size than those fitted at the factory are used, it may be necessary to reprogram the speedometer and make other vehicle modifications. After converting to a different tyre size, have the label with tyre pressures replaced.
170 Vehicle care Tyre chains Tyre chains are only permitted on the front wheels. Always use fine mesh chains that add no more than 10 mm to the tyre tread and the inboard sides (including chain lock). 9 Warning Damage may lead to tyre blowout. 2) Tyre chains are just permitted on tyre sizes 175/70 R 14, 185/60 R 15, 185/65 R 152), 185/70 R 14, 195/55 R 162) and 205/50 R16. Tyre chains are only approved on tyres of size 185/60 R 15 on vehicles with a sports chassis.
Vehicle care To open the compartment, disengage the cover and open it. 1. Take the sealant bottle and bracket with air hose from the insert. 171 3. Position the sealant bottle on the bracket. Make sure that the bottle does not fall. 2. Detach air hose from bracket and screw onto sealant bottle connection. 4. Unscrew valve cap from defective tyre. 5. Screw tyre inflation hose to valve. 6. Screw air hose onto compressor connection. 7. Switch on ignition.
172 Vehicle care 8. Press on/off switch on the compressor. The tyre is filled with sealant. 9. The compressor pressure gauge briefly indicates up to 6 bar whilst the sealant bottle is emptying (approx. 30 seconds). Then the pressure starts to drop. 10. All of the sealant is pumped into the tyre. Then the tyre is inflated. 11. The prescribed tyre pressure should be obtained within 10 minutes. Tyre pressure 3 209.
Vehicle care Notice The driving characteristics of the repaired tyre is severely affected, therefore have this tyre replaced. If unusual noise is heard or the compressor becomes hot, turn compressor off for at least 30 minutes. The built-in safety valve opens at a pressure of 7 bar. Note the expiry date of the kit. After this date its sealing capability is no longer guaranteed. Pay attention to storage information on sealant bottle. Replace the used sealant bottle.
174 Vehicle care Alloy wheels: Disengage wheel bolt caps with a screwdriver and remove. To protect the wheel, place a soft cloth between the screwdriver and the alloy wheel. 2. Install the wheel wrench ensuring that it locates securely and slacken each bolt by half a turn. 3. Ensure the jack is positioned correctly with the vehicle jacking points. With versions of the Corsa VXR with sill panelling or retrofitted sill panelling no jack must be used. The vehicle may be damaged. 4.
Vehicle care 5. 6. 7. 8. 9. Variant 2: Attach jack handle and with the jack correctly aligned rotate handle until wheel is clear of the ground. Unscrew the wheel bolts. Change the wheel. Screw in the wheel bolts. Lower vehicle. Install the wheel wrench ensuring that it locates securely and tighten each bolt in a crosswise sequence. Tightening torque is 110 Nm. 10. Align the valve hole in the wheel cover with the tyre valve before installing. Install wheel bolt caps. 11.
176 Vehicle care In the Corsa van the spare wheel is screwed down together with the floor cover. To lift the cover, undo the plastic nut. There is a spacer between the spare wheel and the floor cover. The spare wheel well is not designed for all permitted tyre sizes. If a wheel wider than the spare must be stowed in the spare wheel well after changing wheels, the floor cover will be resting against the protruding wheel.
Vehicle care Notice Any deviation from the instructions given in this paragraph may lead to a temporary deactivation of the stopstart system. ■ Never expose the battery to naked flames or sparks. ■ A discharged battery can already freeze at temperatures of 0 °C. Defrost the frozen battery before connecting jump leads. ■ Avoid contact with eyes, skin, fabrics and painted surfaces. The fluid contains sulphuric acid which can cause injuries and damage in the event of direct contact.
178 Vehicle care 4. Switch on electrical consumers (e.g. headlights, heated rear window) of the vehicle receiving the jump start. 5. Reverse above sequence exactly when removing leads. 6. Close the cover over the positive pole. Position the leads so that they cannot catch on rotating parts in the engine compartment. To start the engine: 1. Start the engine of the vehicle providing the jump. 2. After 5 minutes, start the other engine.
Vehicle care The towing eye is stowed with the vehicle tools 3 165. The towing eye is located in a recess. Screw in the towing eye as far as it will go until it stops in a horizontal position. Attach a tow rope – or better still a tow rod – to the towing eye. The towing eye must only be used for towing and not recovering the vehicle. Switch on ignition to release steering wheel lock and to permit operation of brake lights, horn and windscreen wiper. Transmission in neutral. Caution Drive slowly.
180 Vehicle care Disengage cap at bottom and remove downwards. The towing eye is stowed with the vehicle tools 3 165. Caution Drive slowly. Do not drive jerkily. Excessive tractive force can damage the vehicle. After towing, unscrew the towing eye and refit the cover. Appearance care Exterior care Locks The locks are lubricated at the factory using a high quality lock cylinder grease. Use de-icing agent only when absolutely necessary, as this has a degreasing effect and impairs lock function.
Vehicle care If using a car wash, comply with the car wash manufacturer's instructions. The windscreen wipers and rear window wiper must be switched off. Remove antenna and external accessories such as roof racks etc. If you wash your vehicle by hand, make sure that the insides of the wheel housings are also thoroughly rinsed out. Clean edges and folds on opened doors and the bonnet as well as the areas they cover. Caution Always use a cleaning agent with a pH value of 4 to 9.
182 Vehicle care Clean rims with a pH-neutral wheel cleaner. Rims are painted and can be treated with the same agents as the body. Paintwork damage Rectify minor paintwork damage with a touch-up pen before rust forms. Have more extensive damage or rust areas repaired by a workshop. Underbody Some areas of the vehicle underbody have a PVC undercoating while other critical areas have a durable protective wax coating. After the underbody is washed, check the underbody and have it waxed if necessary.
Vehicle care Caution Close Velcro fasteners as open Velcro fasteners on clothing could damage seat upholstery. The same applies to clothing with sharp-edged objects, like zips or belts or studded jeans. Plastic and rubber parts Plastic and rubber parts can be cleaned with the same cleaner as used to clean the body. Use interior cleaner if necessary. Do not use any other agent. Avoid solvents and petrol in particular. Do not use highpressure jet cleaners.
184 Service and maintenance Service and maintenance General information ................... 184 Recommended fluids, lubricants and parts .................................... 185 General information Service information In order to ensure economical and safe vehicle operation and to maintain the value of your vehicle, it is of vital importance that all maintenance work is carried out at the proper intervals as specified.
Service and maintenance Fixed service interval When service is due, InSP appears in the odometer display for approximately 10 seconds when the ignition is switched on. Have the next service performed by a workshop within one week or 300 miles (whichever occurs first). Flexible service interval The service interval is based on several parameters depending on usage and calculated using these parameters.
186 Service and maintenance aging control, whereas viscosity grade gives information on the oil's thickness over a temperature range. Dexos is the newest engine oil quality that provides optimum protection for gasoline and diesel engines. If it is unavailable, engine oils of other listed qualities have to be used. Recommendations for gasoline engines are also valid for Compressed Natural Gas (CNG), Liquified Petroleum Gas (LPG) and Ethanol (E85) fuelled engines.
Service and maintenance Brake fluid should be stored in a sealed container to avoid water absorption. Ensure brake fluid does not become contaminated.
188 Technical data Technical data Vehicle identification .................. 188 Vehicle data ............................... 190 Vehicle identification Identification plate Vehicle Identification Number The identification plate is located on the front right door frame. The Vehicle Identification Number is stamped on the identification plate and on the floor pan, under the floor covering, visible under a cover.
Technical data Information on identification plate: 1 = Manufacturer 2 = Type approval number 3 = Vehicle Identification Number 4 = Permissible gross vehicle weight rating in kg 5 = Permissible gross train weight in kg 6 = Maximum permissible front axle load in kg 7 = Maximum permissible rear axle load in kg 8 = Vehicle-specific or country specific data The combined total of front and rear axle loads must not exceed the permissible gross vehicle weight.
190 Technical data Vehicle data Recommended fluids and lubricants European service schedule Required engine oil quality All European countries (except Belarus, Moldova, Russia, Serbia, Turkey) Engine oil quality Only Israel Petrol engines (including CNG, LPG, E85) Diesel engines Petrol engines (including CNG, LPG, E85) Diesel engines dexos 1 – – ✔ – dexos 2 ✔ ✔ – ✔ In case dexos quality is unavailable you may use max. 1 litre engine oil quality ACEA C3 once between each oil change.
Technical data 191 International service schedule Required engine oil quality All countries outside Europe except Israel Engine oil quality Only Belarus, Moldova, Russia, Serbia, Turkey Petrol engines (including CNG, LPG, E85) Diesel engines Petrol engines (including CNG, LPG, E85) Diesel engines dexos 1 ✔ – – – dexos 2 – ✔ ✔ ✔ In case dexos quality is unavailable you may use the oil qualities listed below: All countries outside Europe except Israel Engine oil quality Only Belarus, Moldov
192 Technical data All countries outside Europe except Israel Engine oil quality Only Belarus, Moldova, Russia, Serbia, Turkey Petrol engines Diesel engines Petrol engines (including CNG, LPG, E85) (including CNG, LPG, E85) Diesel engines ACEA A3/B3 ✔ – ✔ – ACEA A3/B4 ✔ ✔ ✔ ✔ ACEA C3 ✔ ✔ ✔ ✔ API SM ✔ – ✔ – API SN resource conserving ✔ – ✔ – Engine oil viscosity grades All countries outside Europe (except Israel), including Belarus, Moldova, Russia, Serbia, Turkey Ambient tempe
Technical data Engine data Sales designation 1.0 1.2 1.2 1.4 A10XEP A12XEL A12XER A14XEL 998 1229 1229 1398 Engine power [kW] 48 51 63 64 at rpm 5300 5600 5600 6000 Torque [Nm] 90 115 115 130 at rpm 4000 4000 4000 4000 Fuel type Petrol Petrol Petrol/LPG Petrol recommended 95 95 95 95 possible 98 98 98 98 possible 91 91 91 91 Oil consumption [l/1000 km] 0.6 0.6 0.6 0.
194 Technical data Sales designation 1.4 1.4 1.6 VXR 1.6 VXR Nürburgring Edition A14XER A14NEL A16LER A16LES 1398 1364 1598 1598 Engine power [kW] 74 88 141 155 at rpm 6000 4800-6000 5850 5850 Torque [Nm] 130 175 230 250 at rpm 4000 1750-4800 1980-5850 2250-5850 Fuel type Petrol Petrol Petrol Petrol recommended 95 95 98 100 possible 98 98 95 98 possible 91 – – – Oil consumption [l/1000 km] 0.6 0.6 0.6 0.
Technical data Sales designation 1.3 CDTI 1.3 CDTI 1.3 CDTI 1.3 CDTI 1.7 CDTI Z13DTJ A13DTE Eco A13DTC A13DTR A17DTS 1248 1248 1248 1248 1686 Engine power [kW] 55 70 55 70 96 at rpm 4000 4000 4000 4000 4000 Torque [Nm] 170 190 190 210 300 at rpm 1750-2500 1750-3250 1750-2250 1750-2500 2000-2500 Fuel type Diesel Diesel Diesel Diesel Diesel Oil consumption [l/1000 km] 0.6 0.6 0.6 0.6 0.
196 Technical data Performance 5-door vehicle Engine A10XEP A12XEL A12XER A14XEL A14XER A14NEL Manual transmission 96 99 1073)4) 108 112 121 Manual transmission automated – – 107 – – – Automatic transmission – – – – 107 – Maximum speed2) [mph] Engine Z13DTJ A13DTC A13DTR A13DTE Eco A17DTS Manual transmission 101 101 108 110 124 Manual transmission automated – – – – – Automatic transmission – – – – – Maximum 2) 3) 4) speed2) [mph] The maximum speed i
Technical data 197 3-door vehicle Engine A10XEP A12XEL A12XER A14XEL A14XER Manual transmission 96 99 1073)4) 108 112 Manual transmission automated – – 107 – – Automatic transmission – – – – 107 Maximum speed2) [mph] Engine A14NEL A16LER A16LES A13DTE Eco Manual transmission 121 140 143 110 Manual transmission automated – – – – Automatic transmission – – – – Maximum speed 2) [mph] 2) 3) 4) The maximum speed indicated is achievable at kerb weight (without dr
198 Technical data Engine Z13DTJ A13DTC A13DTR A17DTS 101 101 108 124 Manual transmission automated – – – Automatic transmission – – – Maximum speed2) [mph] Manual transmission Van Engine A10XEP A12XEL A12XER Manual transmission 96 99 107 Manual transmission automated – – 107 Automatic transmission – – – Maximum speed 2) [mph] 2) The maximum speed indicated is achievable at kerb weight (without driver) plus 200 kg payload.
Technical data Engine Z13DTJ A13DTC A13DTE Eco A13DTR Manual transmission 101 101 110 108 Manual transmission automated – – – – Automatic transmission – – – – Maximum 2) speed2) 199 [mph] The maximum speed indicated is achievable at kerb weight (without driver) plus 200 kg payload. Optional equipment could reduce the specified maximum speed of the vehicle.
200 Technical data Vehicle weight Kerb weight, 5-door vehicle, basic model without any optional equipment Corsa Engine Manual transmission Manual transmission automated Automatic transmission 1145/1165 – – 1163/1178 – – A12XER 11635)/11785) – – A14XEL 1163/1178 – 1188/1208 A14XER 1163/1178 – – A14NEL 1237/1252 – – A13DTC 1235/1255 – – Z13DTJ 1235/1255 – – 1199/1209 – without/with air conditioning/climate control A10XEP [kg] A12XEL without/with air conditioning/climate
Technical data Kerb weight, 5-door vehicle, basic model with all optional equipment Corsa Engine Manual transmission Manual transmission automated Automatic transmission –/1280 – – –/1278 – – A12XER –/12786) – – A14XEL –/12787) – –/1317 A14XER –/12787) – – A14NEL –/1361 – – A13DTC –/1365 – – Z13DTJ –/1365 – – –/1318 – –/1396 – – – without/with air conditioning/climate control A10XEP [kg] A12XEL without/with air conditioning/climate control A13DTE ECO –/1318 [kg] A13D
202 Technical data Kerb weight, 3-door vehicle, basic model without any optional equipment Corsa Engine Manual transmission Manual transmission automated Automatic transmission 1100/1120 – – 1120/1135 – – A12XER 11208)/11358) – – A14XEL 1141/1156 – – A14XER 1141/1156 – 1165/1185 A14NEL 1199/1214 – – A16LER 1278/1293 – – A16LES 1278/1293 – – A13DTC 11639)/117310) – – without/with air conditioning/climate control A10XEP [kg] A12XEL 8) 9) 10) With LPG engine weight in
Technical data Corsa Engine Manual transmission without/with air conditioning/climate control Z13DTJ 1205/1225 [kg] A13DTE ECO 1163/1173 Manual transmission automated Automatic transmission – – 1163/1173 – A13DTR 1235/1255 1235/1255 – A17DTS 1278/1298 – – 203
204 Technical data Kerb weight, 3-door vehicle, basic model with all optional equipment Corsa Engine Manual transmission Manual transmission automated Automatic transmission –/1235 – – –/1259 – – A12XER –/125911) – – A14XEL –/1278 – – A14XER –/1278 – –/1299 A14NEL –/1318 – – A16LER –/1318 – – A16LES –/1318 – – A13DTC –/131812) – – – – –/1278 – without/with air conditioning/climate control A10XEP [kg] A12XEL without/with air conditioning/climate control Z13DTJ –/
Technical data Kerb weight, van, basic model without any optional equipment Corsa Engine Manual transmission Manual transmission automated without/with air conditioning/climate control A10XEP 1125/1145 [kg] A12XEL 114013)/116013) 13) Automatic transmission – – – – A12XER 114013)/116013) 114013)/116013) – Z13DTJ 121513)/123513) – – A13DTC 121513)/123513) – – A13DTR 124513)/126513) – – In conjunction with 17" wheels, weight increased by 20 kg.
206 Technical data Kerb weight, van, basic model with all optional equipment Corsa Engine Manual transmission Manual transmission automated without/with air conditioning/climate control A10XEP –/1230 [kg] A12XEL –/124514) Automatic transmission – – – – A12XER –/124514) –/124514) – Z13DTJ –/132014) – – A13DTC –/132014) – – A13DTR –/135014) – – Vehicle dimensions 5-door vehicle 3-door vehicle VXR Van Length [mm] 3999 3999 4040 3999 Width without exterior mirrors [mm] 1737 1
Technical data 207 5-door vehicle 3-door vehicle VXR Van Length of load compartment with folded rear seats [mm] 1348 1348 1348 – Load compartment width [mm] 944 944 944 944 Load compartment height [mm] 538 538 538 538 Wheelbase [mm] 2511 2511 2511 2511 Turning circle diameter [m] 10.2 10.2 10.2 10.
208 Technical data Capacities Engine oil A14XEL, A14XER, A14NEL A16LER, A16LES A13DTE, A13DTC A13DTR, Z13DTJ A17DTS Engine A10XEP A12XEL, A12XER including Filter [l] 3.0 4.0 4.0 4,5 3.5 3.5 5.4 between MIN and MAX [l] 1.0 1.0 1.0 1.0 1.0 1.0 1.
Technical data 209 Tyre pressures Engine Tyres Comfort with up to 3 people ECO with up to 3 people16) With full load front front rear [kPa/bar] ([psi]) [kPa/bar] ([psi]) rear [kPa/bar] [kPa/bar] ([psi]) ([psi]) A10XEP 185/70 R14, 200/2.0 (29) front [kPa/bar] [kPa/bar] ([psi]) ([psi]) 180/1.8 (26) 270/2.7 (39) 185/65 R15, 185/60 R1517), 195/60 R15, 195/55 R1618) 16) 17) 18) rear To achieve the smallest amount of fuel consumption possible. Only permitted as winter tyres.
210 Engine Technical data Tyres Comfort with up to 3 people ECO with up to 3 people16) With full load front front rear [kPa/bar] ([psi]) [kPa/bar] ([psi]) rear [kPa/bar] [kPa/bar] ([psi]) ([psi]) A12XEL, 185/70 R14, A12XER, 185/65 R1519), A14XEL, 185/60 R1517), A14XER 195/60 R15, 200/2.0 (29) front rear [kPa/bar] [kPa/bar] ([psi]) ([psi]) 180/1.8 (26) 270/2.7 (39) 250/2.5 (36) 260/2.6 (38) 320/3.
Technical data Engine Tyres Comfort with up to 3 people ECO with up to 3 people16) With full load front front rear [kPa/bar] ([psi]) [kPa/bar] ([psi]) rear [kPa/bar] [kPa/bar] ([psi]) ([psi]) A14NEL 195/65 R15, 196/60 211 front rear [kPa/bar] [kPa/bar] ([psi]) ([psi]) 230/2.3 (33) 210/2.1 (30) 280/2.8 (41) 260/2.6 (38) 250/2.5 (36) 320/3.2 (46) 250/2.5 (36) 230/2.3 (33) – – 240/2.4 (34) 220/2.2 (32) 270/2.7 (39) 250/2.5 (36) 260/2.6 (38) 320/3.2 (46) 260/2.6 (38) 240/2.
212 Engine Technical data Tyres Comfort with up to 3 people ECO with up to 3 people16) With full load front front rear [kPa/bar] ([psi]) [kPa/bar] ([psi]) rear [kPa/bar] [kPa/bar] ([psi]) ([psi]) A13DTC 185/65 R1521), front rear [kPa/bar] [kPa/bar] ([psi]) ([psi]) 200/2.0(29) 180/1.8 (26) 270/2.7 (39) 250/2.5 (36) 260/2.6 (38) 320/3.2 (46) 220/2.2 (32) 180/1.8 (26) 270/2.7 (39) 250/2.5 (36) 260/2.6 (38) 320/3.2 (46) 270/2.7 (39) 250/2.5 (36) 270/2.7 (39) 250/2.5 (36) 270/2.
Technical data Engine Tyres 213 Comfort with up to 3 people ECO with up to 3 people16) With full load front front rear [kPa/bar] ([psi]) [kPa/bar] ([psi]) rear [kPa/bar] [kPa/bar] ([psi]) ([psi]) front rear [kPa/bar] [kPa/bar] ([psi]) ([psi]) A13DTR 185/60 R15 240/2.4 (34) 200/2.0 (29) 270/2.7 (39) 250/2.5 (36) 260/2.6 (38) 320/3.2 (46) 185/65 R15 220/2.2 (32) 200/2.0 (29) 270/2.7 (39) 250/2.5 (36) 260/2.6 (38) 320/3.2 (46) 195/55 R1618) 220/2.2 (32) 200/2.0 (29) 270/2.
214 Engine Technical data Tyres Comfort with up to 3 people ECO with up to 3 people16) With full load front front rear [kPa/bar] ([psi]) [kPa/bar] ([psi]) rear [kPa/bar] [kPa/bar] ([psi]) ([psi]) Z13DTJ front rear [kPa/bar] [kPa/bar] ([psi]) ([psi]) 200/2.0 (29) 180/1.8 (26) 270/2.7 (39) 250/2.5 (36) 260/2.6 (38) 320/3.2 (46) 185/60 R1517) 220/2.2 (32) 180/1.8 (26) 270/2.7 (39) 250/2.5 (36) 260/2.6 (38) 320/3.2 (46) A17DTS 185/65 R1526), 240/2.4 (35) 220/2.2 (32) 270/2.
Technical data Engine Tyres Comfort with up to 3 people ECO with up to 3 people16) With full load front front rear [kPa/bar] ([psi]) [kPa/bar] ([psi]) rear [kPa/bar] [kPa/bar] ([psi]) ([psi]) 185/60 R1517) all 17) 260/2.6 (38) Temporary spare wheel 420/4.2 (61) Only permitted as winter tyres. 215 front rear [kPa/bar] [kPa/bar] ([psi]) ([psi]) 220/2.2 (32) 270/2.7 (39) 250/2.5 (36) 260/2.6 (38) 320/3.2 (46) 420/4.2 (61) – – 420/4.2 (61) 420/4.
216 Technical data Towing hitch installation dimensions
Customer information Customer information Vehicle data recording and pri‐ vacy ........................................... 217 Vehicle data recording and privacy Event data recorders Data storage modules in the vehicle A large number of electronic components of your vehicle contain data storage modules temporarily or permanently storing technical data about the condition of the vehicle, events and errors.
218 Customer information When using the vehicle, situations may occur in which these technical data related to other information (accident report, damages on the vehicle, witness statements etc.) may be associated with a specific person possibly, with the assistance of an expert. Additional functions contractually agreed upon with the client (e.g. vehicle location in emergency cases) allow the transmission of particular vehicle data from the vehicle.
Customer information 219
220 Index A Accessories and vehicle modifications .......................... 141 Active head restraints .................. 35 Adaptive forward lighting .......... .................................... 83, 97, 152 Adjustable air vents ................... 109 Airbag and belt tensioners ........... 78 Airbag deactivation ................ 43, 78 Airbag system .............................. 41 Air conditioning regular operation ................................ 110 Air conditioning system ..............
221 Climate control ............................. 15 Climate control systems............. 103 Clock ............................................ 72 Control indicators ......................... 76 Control of the vehicle ................. 111 Controls........................................ 68 Convex shape .............................. 27 Coolant and antifreeze............... 185 Cruise control ...................... 83, 128 Cupholders .................................. 51 Curtain airbag system .............
222 Heated ......................................... 28 Heated rear window ..................... 31 Heated steering wheel ................. 69 Heating ........................................ 38 Heating and ventilation system . 103 High beam ............................. 82, 96 Hill start assist ........................... 126 Horn ....................................... 13, 69 I Identification plate ..................... 188 Ignition switch positions ............. 112 Immobiliser ........................
223 Q Quickheat................................... 109 R Radio Frequency Identification (RFID) .................................... 218 Radio remote control ................... 20 Reading lights ............................ 101 Rear carrier system...................... 52 Rear floor storage cover .............. 64 Rear fog light ............................... 83 Rear fog lights ............................. 99 Rear window wiper/washer .......... 71 Recommended fluids and lubricants .....................
224 Upshift.......................................... 80 Using this manual .......................... 3 V Vehicle checks............................ 142 Vehicle data................................ 190 Vehicle data recording and privacy..................................... 217 Vehicle dimensions .................... 206 Vehicle Identification Number .... 188 Vehicle jack................................ 165 Vehicle messages ....................... 87 Vehicle personalisation ...............
